Road Disc Hub

12×100mm Front, 12×142mm Rear Thru-Axle Road Disc Hub Set: Specifications for OEM Builders

17 min read
On this page 5 sections

The quickest way to avoid a costly sampling cycle is to treat 12×100mm front and 12×142mm rear thru-axle spacing as a fit commitment rather than a headline number. For a road disc wheel build, those figures describe the dropout interface on the frame and fork: a 12mm-diameter thru-axle with a 100mm over-locknut distance at the front, and the same 12mm axle diameter with a 142mm over-locknut distance at the rear. If the frame and fork do not use that pairing, the hub set will not install regardless of how well the rest of the specification reads on paper.

That is the first gate in the buyer's checklist, and it is the one the ARC MT-005F/R is built around. The ARC MT-005F/R J-Bend 6-Bolt Road Disc Hub Set is an OEM-oriented road disc hub set with 12×100mm front and 12×142mm rear thru-axle spacing, offered with 28H, 32H and 36H drilling and a choice of Shimano HG or SRAM XDR freehub. For product managers and wheelset brands assembling an aftermarket or complete-bike program, the practical task is to confirm this fit condition first, then line up the remaining parameters that the axle spacing alone does not settle.

What 12×100mm Front and 12×142mm Rear Thru-Axle Spacing Means for a Road Disc Build

The two numbers are often read as one specification, but they answer different questions. The 12mm value is the axle diameter, which must match the thru-axle the frame or fork is designed to accept. The 100mm and 142mm values are the over-locknut distances, which set where the hub flanges and axle ends sit relative to the dropouts. A road disc fork built for 12×100mm will not accept a hub with a different over-locknut distance, and the reverse is equally true.

For OEM buyers, this has three downstream consequences. First, hub width determines the dish and spoke geometry, so a wheel built around the correct axle standard will assemble with the intended bracing angles. Second, the thru-axle standard affects rotor alignment and caliper positioning, because the brake mount on the frame and fork assumes a specific hub centerline. Third, it fixes the axle end caps, which is why end cap configuration should be confirmed as part of the axle standard rather than treated as an afterthought.

The MT-005F/R's spacing is stated as 12×100mm front and 12×142mm rear, which is the common road disc pairing. Buyers should still check their own frame and fork drawings before committing, because a hub set that matches one frame platform may not match another if the dropout design or axle hardware differs. Confirming this early is cheaper than discovering it at the build stage.

MT-005F/R Specification Points That Must Match Before Ordering

Once the axle standard is confirmed, the remaining MT-005F/R specification points become the real sourcing checklist. Several of them interact, so it helps to review them together rather than in isolation.

  • Brake interface: The hub set uses a 6-bolt disc mount. This constrains rotor selection to 6-bolt rotors and must match what the frame and fork brake system expects; a Center Lock specification would be a different build decision entirely.
  • Spoke interface: The J-bend design uses conventional flanged hubs and J-bend spokes, which matters for spoke sourcing, lacing patterns and the wheel builder's tooling. It is a different starting point from straight-pull designs.
  • Construction materials: The hub shell is AL6061-T6 aluminum, while the axle, freehub body and end caps are high-strength AL7075 aluminum. This combination is relevant to buyers weighing weight against durability in a road disc application.
  • Drivetrain engagement: The hub set uses a 4-pawl, single-tooth engagement system, which is the mechanism behind power transfer and drivetrain response. Buyers should understand this as a design characteristic to evaluate against their ride and performance targets, not as a standalone performance guarantee.
  • Bearings and weight: S&S steel bearing options are listed, and total weight is approximately 414.3g. The word "approximately" matters here: weight should be confirmed for the specific configuration ordered, since hole count and freehub choice can affect the final figure.

Each of these is a specification the buyer can verify against the product data, and each one narrows the build. A 6-bolt hub with J-bend spokes and AL7075 axle components is a coherent package for a road disc wheelset, but only if the buyer's rim, rotor and spoke plan align with it.

Why the Freehub and Spoke Count Decisions Belong Up Front

Freehub and drilling choices are often left until late in a program, yet they are among the hardest decisions to reverse once rims and cassettes are specified. The MT-005F/R is offered with Shimano HG or SRAM XDR freehub compatibility, and that choice determines which cassette families the wheelset can accept. A Shimano HG freehub and an SRAM XDR freehub are not interchangeable at the cassette interface, so the drivetrain specification for the complete bike or aftermarket wheelset should be settled before the hub order is placed.

Spoke count follows a similar logic. The 28H, 32H and 36H options must match the rim drilling the buyer intends to use; a 32H hub cannot be laced to a 28H rim. Beyond the mechanical match, hole count is a design decision that reflects the intended rider load, wheel stiffness targets and the builder's preferred lacing pattern. Because the MT-005F/R offers three drilling options, buyers have room to standardize on one hub platform across several wheel models, but each model's rim and spoke plan should be confirmed against the chosen count.

Treating these two decisions as front-end inputs rather than late adjustments keeps the sampling process focused. It also makes the weight reference more meaningful, since the approximately 414.3g figure should be read in the context of the exact configuration under evaluation.

Confirming the Specification with ARC as an OEM/ODM Partner

For buyers sourcing at volume, the specification sheet is the starting point for a conversation rather than the end of it. ARC, based in Taicang, Jiangsu, China, has manufactured bicycle hubs since 2013 and provides OEM and ODM solutions for bicycle brands, wheel manufacturers and distributors, including road bike applications. That background is relevant here because the MT-005F/R is positioned as an OEM/ODM-oriented road disc hub set rather than a single retail SKU.

The practical next step is to confirm the build-specific details with ARC before sampling. That means verifying the frame and fork axle standard against the 12×100mm front and 12×142mm rear spacing, confirming the 6-bolt rotor interface and J-bend spoke plan, settling the Shimano HG or SRAM XDR freehub choice, and selecting the 28H, 32H or 36H drilling that matches the rim. The S&S steel bearing option and the approximately 414.3g weight reference should also be confirmed for the exact configuration being evaluated, since these figures are configuration-dependent.

ARC's stated capabilities in CNC machining, precision manufacturing and quality control are the relevant context for that discussion, along with its OEM/ODM customization scope. Buyers should frame their questions around what they can verify: the axle and brake interface fit, the freehub standard, the drilling, the materials and the bearing option. Those are the points that decide whether the hub set suits a given road disc program.

For a road disc wheelset program with a 12×100mm front and 12×142mm rear thru-axle frame platform, the ARC MT-005F/R is worth putting on the evaluation list, provided the 6-bolt interface, J-bend spoke plan, freehub standard and hole count all line up with the intended build. The most efficient path is to confirm those parameters directly with ARC, then move to sampling with a specification that has already been checked against the frame, rim and drivetrain rather than one that still needs to be reconciled.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China