Dirt jump front wheels live a contradictory life: they need to stay rigid under repeated case landings and hard nose-first impacts, yet they must remain light enough for the front end to be thrown around. The 15×100mm thru-axle, 6-bolt disc and J-bend spoke combination has become a practical baseline for this job, and the ARC MT-013F is built directly around it. Before ordering samples or committing to production, wheel builders and brand product managers should understand why these three interfaces belong together, which configuration choices actually change the ride, and which details need written confirmation from the hub supplier.
Why This Axle, Disc and Spoke Combination Fits Dirt Jump Front Wheels
The 15×100mm thru-axle addresses the most important weakness of a dirt jump front wheel: keeping the axle-to-fork connection tight when the wheel takes repeated, uneven loads. A thru-axle clamps the hub between the fork legs rather than relying on a quick-release skewer, so wheel location stays consistent after hard landings and frequent wheel removal. For dirt jump frames and forks designed around this standard, the 15mm diameter also gives a stiffer interface than a narrower axle while keeping the hub shell compact. Buyers should confirm that their fork and dropout spacing are genuinely 15×100mm, because this is a frame-and-fork–driven decision, not a hub-driven one.
The 6-bolt disc mount matters for a different reason: serviceability. Six-bolt rotors are widely available, easy to source in different diameters, and simple to remove with standard tools. On a dirt jump build, where the front brake may be run, swapped or removed depending on riding style and local rules, a 6-bolt interface keeps rotor choice flexible and spare parts easy to find. It also avoids committing the wheel build to a proprietary rotor standard.
J-bend spokes complete the package for wheel builders. J-bend spokes are laced through traditional hub flanges, which means the builder can use familiar lacing patterns, standard spoke lengths and widely stocked 14G spokes. The bend absorbs some of the spoke's fatigue at the flange, and the flange geometry gives predictable tensioning behavior. Straight-pull designs have their place, but for dirt jump wheels that are rebuilt or re-tensioned after abuse, J-bend remains the lower-risk, easier-to-service choice. The MT-013F ties these three interfaces to a shell made from AL6061-T6 aluminum and an axle and end caps machined from high-strength AL7075 aluminum, a material pairing intended to balance weight and impact durability.
Configuring the MT-013F: Hole Count, Spokes and Bearings
Once the axle and interface standards are fixed, the real build decisions are hole count and bearing specification. The ARC MT-013F 6-Bolt Dirt Jump Front Hub is offered in 28H, 32H and 36H drillings, and each points to a different wheel-building philosophy.
| Configuration | Typical build intent | What the buyer should verify |
|---|---|---|
| 28H | Lower spoke count, lighter front wheel, riders prioritizing weight | Rim stiffness and spoke tension limits; suitability for heavier riders or very aggressive landings |
| 32H | General-purpose dirt jump and demanding MTB front builds | Balanced weight and durability; common rim and spoke availability |
| 36H | Maximum redundancy and impact tolerance | Rim availability in 36H; slightly higher weight |
All three use 14G J-bend spokes, so the builder should calculate spoke lengths against the actual flange dimensions and chosen rim rather than assuming a generic length. The hub's S&S steel bearing options are the other key choice: steel bearings are a practical default for dirt jump use because they tolerate the shock loads and occasional water exposure better than lightweight alternatives, but buyers should ask which S&S bearing grade is fitted and whether the seals suit wet or dusty conditions.
Weight context helps set expectations. The MT-013F is quoted at approximately 206.2g, which is competitive for a thru-axle hub with a 6-bolt mount and steel bearings. Builders should treat that figure as a hub-only reference and add rotor bolts, axle hardware and spokes when comparing complete wheel weights.
What to Confirm Before Sampling or Bulk Ordering
A sample hub that fits a fork is not the same as a production batch that builds consistent wheels. Buyers should turn the following into written checkpoints before committing:
- Axle and dropout fit: Confirm the 15×100mm standard against the actual fork, including end-cap profile and any torque specification the supplier recommends.
- Bearing play and sealing: Check for axial and radial play out of the box, then confirm the bearing grade and seal type in writing, since "S&S steel bearing options" can cover more than one specification.
- Spoke interface: Measure flange dimensions and confirm 14G J-bend compatibility, then build a test wheel and check tension retention after a period of riding.
- Disc alignment: Mount a 6-bolt rotor and confirm the rotor sits within the expected caliper adjustment range, since small variations affect brake setup time on the production line.
- Batch consistency: Ask how hole count, bearing fit and axle tolerances are controlled across lots, and request the inspection criteria used at final check.
- OEM/ODM terms: Clarify customization scope, sample lead time, minimum order quantities and packaging requirements. These should be stated by the supplier, not assumed.
For buyers sourcing through an OEM/ODM route, the most useful questions are about change control: what can be customized, what stays fixed for structural reasons, and how a revision is documented between sample approval and mass production.
Working With ARC as a Hub OEM/ODM Partner
For brands and wheel builders who have settled on a 15×100mm thru-axle, 6-bolt disc and J-bend spoke front hub, the remaining question is supplier fit. ARC, operated by Taicang Xiangyue Sports Equipment Co., Ltd., has manufactured bicycle hubs since 2013 from its base in Taicang, Jiangsu, China, using CNC machining and quality control processes aimed at OEM and ODM supply. The company's stated work covers MTB, road, gravel and e-bike hubs for bicycle brands, wheel manufacturers and distributors, which matches the profile of a buyer developing a dirt jump wheelset rather than a one-off retail purchase.
The MT-013F is the concrete starting point for this specification: a dedicated dirt jump front hub with the exact axle standard, 6-bolt mount, J-bend drilling and S&S steel bearing options discussed above, available in 28H, 32H and 36H. Its aluminum shell and AL7075 axle indicate where ARC has chosen to spend material for impact resistance, and the approximate 206.2g figure gives buyers a baseline for weight planning. What ARC can usefully support is the evaluation stage: confirming the configuration that fits the intended rider and rim, supplying samples for build and ride testing, and discussing OEM/ODM customization within the hub's documented scope. Buyers with a defined dirt jump front wheel program should shortlist the MT-013F configuration, request a sample built to their chosen hole count and bearing option, and use the checkpoints above to decide whether the hub is ready for a production order.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China