Fixed-Gear Wheel Builders

ARC GT-010FA/RA Track Hub Set for Fixed-Gear Wheel Builders

13 min read
On this page 5 sections

For builders putting together a dedicated track wheelset or a custom fixed-gear setup, the hub choice is rarely just about weight. It sets the shell material, the axle strength, how securely the drivetrain is held, what sprocket options are open, and which rims can be laced. The ARC GT-010FA/RA Track Hub Set is a relevant option to examine, because the ARC product documentation frames it specifically around track cycling and fixed-gear applications and lists the construction details that matter to wheel builders.

What This Hub Set Is Built For

The GT-010FA/RA is positioned for track and fixed-gear builds rather than as a general-purpose hub. That focus shows in its configuration: a fully CNC-machined AL6061-T6 aluminum shell, an AL7075 aluminum axle and components, stainless steel locking hardware, double-sided fixed-gear threading, 20-hole front and 24-hole rear drilling, a supplied 16T fixed-gear sprocket and lockring, S&S steel bearing options, and a total weight of approximately 512g.

For a wheel builder, that reads as a build-ready package. The drilling counts, the included cog and lockring, and the material specification all feed directly into rim choice, spoke calculation and drivetrain planning. Fixed-gear and track riders apply torque through the drivetrain in a way that freehub designs do not face, so the locking structure and thread layout deserve more attention than they would on a road hub.

Materials and Torque Retention in Fixed-Gear Use

Fixed-gear riding loads the hub differently from geared riding. Pedaling and, critically, resisting or braking through the legs sends torque through the sprocket and into the hub body in both directions. That places demands on the shell, the axle and the hardware that secures the sprocket.

The GT-010FA/RA addresses this with a combination of AL6061-T6 for the shell and AL7075 for the axle and components. AL6061-T6 is a heat-treated aluminum grade commonly chosen for machined structural parts, while AL7075 is a higher-strength aluminum alloy often used where stiffness and strength-to-weight matter. The product documentation states this material pairing alongside a fully CNC-machined shell. For builders, the practical point is that the shell and axle are specified as machined aluminum rather than mixed or unspecified materials, which makes the hub easier to assess against the torque demands of fixed-gear use.

The integrated locking structure with stainless steel locking hardware is the other piece that matters here. Stainless steel hardware is stated for the locking elements, which is relevant given that these parts are repeatedly tightened and loaded. Builders should still confirm the recommended tightening procedure and torque values with ARC before final assembly, since the documentation describes the locking structure and materials but does not publish torque figures in the material reviewed here.

Weight sits at approximately 512g for the set. That is a stated figure rather than a claim about performance, and builders should treat it as one input among several when comparing against rim and spoke choices for a track build.

Threading, Cog and Drilling for Wheel Builders

The drivetrain side of the GT-010FA/RA is where the wheel builder's planning decisions concentrate. Double-sided fixed-gear threading supports flexible sprocket positioning, which matters when a rider wants to change gearing or set up the drivetrain on either side of the hub. The set is supplied with a 16T fixed-gear sprocket and lockring, so a builder can plan a complete drivetrain around the included cog rather than sourcing it separately.

The 20H front and 24H rear drilling is the other planning anchor. These are the spoke counts a builder needs for rim selection, spoke length calculation and lacing pattern. A 20-hole front and 24-hole rear pairing is a defined configuration, and builders should match rims and spokes to those counts rather than assuming a different drilling is available. Where a project calls for a different spoke count or threading layout, that is a configuration question to raise with ARC rather than something to infer from this model.

Two practical checks belong before ordering. First, confirm that the intended chainline and frame spacing align with the hub's stated configuration, since the documentation reviewed here does not list axle spacing dimensions. Second, confirm the cog and lockring specification matches the gearing the rider intends to run, and whether alternative cog sizes are supported. These are specification questions, not limitations of the product, and clarifying them early keeps the build on schedule.

Sourcing the GT-010FA/RA Through ARC

ARC is a bicycle hub manufacturer based in Taicang, Jiangsu, China, founded in 2013 and focused on the research, development, manufacturing and customization of high-performance hubs. The company offers OEM and ODM solutions for bicycle brands, wheel manufacturers and distributors. That background is relevant to wheel builders and wheelset brands who need more than a single off-the-shelf hub: it means the GT-010FA/RA can be discussed as part of a broader sourcing conversation.

For a fixed-gear or track wheelset program, the documented features of the GT-010FA/RA give buyers a concrete starting point. The shell and axle materials, the integrated locking structure with stainless steel hardware, the double-sided threading, the 20H/24H drilling and the supplied 16T cog and lockring are all stated facts that can be checked against a build sheet or a product brief. Builders evaluating this hub should compare those points against their drivetrain, spoke count and torque requirements, then confirm configuration and OEM/ODM terms directly with ARC.

The product detail page for the ARC GT-010FA/RA Track Bike Hubs is the natural reference for the stated specifications. Where a project needs a track or fixed-gear hub with a machined aluminum shell, a stated axle alloy, stainless locking hardware and a build-ready cog and lockring, the GT-010FA/RA is worth placing on the evaluation list and taking into a direct specification discussion with ARC.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China