Road Disc Hub

ARC MT-037F/R Road Disc Hub Set: What Wheel Builders Get and Who It Suits

18 min read
On this page 6 sections

Wheel builders sourcing road disc hubs face a narrow set of decisions that shape the rest of the build: spoke count and lacing pattern, rotor interface, axle spacing, freehub standard, and how much internal engagement and bearing specification the target wheelset actually needs. The ARC MT-037F/R 24H Straight-Pull Center Lock Road Disc Hub Set is a direct answer to those decisions in a single package. This is a hub set built around modern road disc frames, with a configuration list long enough to cover most of the drivetrain and rotor combinations a builder will encounter, and specific enough that a builder can quickly judge whether it belongs on the bench.

What the MT-037F/R is, in build terms

In straightforward terms, this is a road disc hub set with a precision-machined AL6061-T6 aluminum hub shell paired to a high-strength AL7075 aluminum axle, freehub body, and end caps. Both front and rear are 24-hole straight-pull, the rotor mount is Center Lock, and the axle spacing is 12×100mm front with 12×142mm rear thru-axle. The freehub is offered in Shimano HG, Road Micro Spline, SRAM XDR, Campagnolo N3W, and Campagnolo 11/12-speed versions. The drive system uses a 36T or 54T ratchet with ARC's patented one-piece ratchet architecture, bearings are available in steel or ceramic, and ARC lists a total weight of approximately 376.3g for the set.

For a wheel builder, the value of that package is less about any single figure and more about how the pieces line up with a planned wheelset. A 24H straight-pull hub set sets the spoke count across both wheels and dictates the spoke type, which has to be settled before rim and spoke ordering, not after. Center Lock fixes the rotor attachment method and the tools required at assembly. The thru-axle spacing places the hub squarely in current road disc frames and forks. And the freehub list means one hub platform can serve several drivetrain families without a second design. This is the sense in which the MT-037F/R is a road-specific hub set rather than a general-purpose one — it is configured for road disc builds from the start.

Fitting the hub to a road disc build

The first check is axle spacing. A 12×100mm front and 12×142mm rear thru-axle pair matches the standard road disc frame and fork interface, so any build already planned around that spacing can accept the hub set without adapters or rework. Builders working with older quick-release frames or non-standard spacing should confirm this before committing, because the stated configuration does not describe conversion options.

The second check is the freehub. Five standards are listed, which covers the common road groupsets: Shimano HG and Road Micro Spline for Shimano drivetrains, SRAM XDR for SRAM road and gravel groupsets, and Campagnolo N3W plus Campagnolo 11/12-speed for Campagnolo users. A builder assembling a run of wheels for several brands, or a wheelset brand serving riders across groupset families, can therefore standardize on one hub shell and vary only the freehub body. That matters for inventory, for service parts, and for how a wheel range is presented to dealers.

The third check is spoke planning. Straight-pull 24H front and rear is a specific build architecture: spokes are not J-bend, and the count is fixed. ARC describes this configuration as supporting efficient spoke integration and balanced wheel construction, but the practical consequence for a builder is simply that spoke length and type must be calculated for a straight-pull 24H lacing pattern, and that rims and spokes should be selected with that pattern in mind. A builder who has not worked with straight-pull hubs will need to verify spoke availability and tension targets before quoting a build.

Center Lock is the least ambiguous part of the package. Road disc rotors are widely available in Center Lock, the interface is tool-simple, and it avoids the tolerance questions that can arise with six-bolt mounting on repeated rotor changes.

Choosing ratchet and bearing configuration

Two of the hub's internal specifications are offered as choices rather than fixed: the ratchet tooth count and the bearing type.

The 36T and 54T ratchets differ in engagement points per revolution. More teeth means a shorter engagement arc before drive is taken up, which some riders notice in technical or repeated acceleration situations; fewer teeth can mean a different trade-off in drag and tooth loading. The MT-037F/R uses ARC's patented one-piece ratchet architecture across both options, which ARC states provides reliable engagement, efficient power transfer, and enhanced structural rigidity. For a builder, the useful position is to match the choice to the wheelset's intended rider and terrain rather than to default to the higher count. A road wheelset for steady training and sportive use and a wheelset for criterium or mixed-surface use may reasonably be specified differently. The important constraint is that the choice should be made at order stage, because it is a build-time configuration.

Bearing choice works the same way. Steel and ceramic are both listed as options. The hub set's specification does not state differences in bearing life, friction, or service intervals between the two, and a builder should not assume them. Steel is the conventional baseline; ceramic is a specification some customers request. Which one a given wheelset ships with is a commercial and application decision, not a claim the data supports as a performance conclusion.

ARC's product page for the ARC MT-037F/R 24H Straight-Pull Center Lock Road Disc Hub Set is the reference point for the current stated configuration when a builder prepares a specification sheet.

Where a wheel builder's open questions remain

The published specification answers the fit questions well. It does not answer several questions a builder will reasonably ask before sampling, and it is worth being explicit about which are which.

Not established by the product data: test data on ratchet durability, bearing life under load, or hub shell fatigue; pricing at different quantity levels; production lead times; sampling terms; and the specific quality-control methods applied to each batch. ARC's company profile states that it operates CNC machining, precision manufacturing, professional engineering expertise, and strict quality-control systems, and that is the relevant capability background, but it is a general statement about the production base rather than a per-product test report.

The approximately 376.3g system weight is a specification reference. It should not be read as a performance claim, and it will not translate directly into a complete wheelset weight once spokes, rim, nipples, rotor lockrings, and freehub variation are included.

The sensible next step for a builder with a live project is a sample request with the intended freehub standard, ratchet count, and bearing type specified, so the sample matches the production intent. Questions about tolerances, batch consistency, and inspection documentation belong in that same conversation rather than being inferred from the catalogue page.

The OEM/ODM angle

For wheelset brands and bicycle brand product managers, the MT-037F/R is most useful as an entry point to a customization discussion rather than a catalogue-only purchase. ARC was founded in 2013 in Taicang, Jiangsu, China, and provides OEM and ODM solutions for bicycle brands, wheel manufacturers, and distributors across MTB, road, gravel, and e-bike categories. The freehub, ratchet, and bearing options on this hub set are exactly the kind of variables that a customization conversation would normally work through — which standards a brand's wheel range needs to cover, which configuration becomes the standard build, and which becomes an option.

That makes ARC a reasonable candidate to include in a supplier evaluation for road disc hub programs, particularly for a brand that wants one hub platform spanning Shimano, SRAM, and Campagnolo drivetrains. The fit is strongest for builders and brands whose road disc wheelsets already sit on 12×100/12×142 thru-axle frames, who can work within a 24H straight-pull architecture, and who want the freehub and internal specification decided at order rather than adapted afterward. For those buyers, requesting a sample in the exact intended configuration, and opening the OEM/ODM conversation around the standards the range needs, is the practical way to move from specification to a verified build.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China