For a carbon-spoke road disc wheelset, the hub is not a background component. Its flange geometry, spoke interface and bearing package set how the wheel takes tension, how it feels under braking and how easily the build can be repeated across a production run. The ARC MT-105F/R 18/21H carbon-spoke Center Lock road hub set is built around that reality, pairing an asymmetric 18-hole front and 21-hole rear with 2:1 lacing so that a lightweight carbon-spoke wheel can be planned around a defined, repeatable foundation rather than adapted to a general-purpose hub.
Why an 18H/21H 2:1 Layout Changes the Build Brief
Hole count and lacing decide the rim drilling, the spoke lengths, the tension targets and the assembly method before a single component is ordered. The MT-105F/R fixes those choices early: 18 holes at the front, 21 at the rear, with the rear built on a 2:1 ratio. In practice, that means the rear wheel distributes its spokes in two groups—twice as many on one side as the other—rather than splitting them evenly.
ARC states that this asymmetric configuration is intended to optimise spoke tension balance and load distribution. The engineering logic is straightforward: a rear disc hub is not symmetric in the loads it carries, because the cassette side and the disc side do not share the same dish or the same drive forces. A 2:1 layout lets the builder assign more spokes to the side that needs them, which helps bring the two sides of the wheel closer in tension instead of leaving one side slack. For a carbon-spoke build, where spoke tension and rim stiffness interact closely, that balance is a practical assembly advantage rather than a detail.
The front stays at 18 holes, which suits a lightweight road disc wheel where the front carries less drive torque and the priority is a clean, low-spoke-count build. OEM buyers should treat the 18/21 pairing as a matched system: rims must be drilled to the same counts and the same 2:1 rear pattern, and spoke lengths must be calculated for the actual flange geometry rather than assumed from a previous 20/24 project. Before committing, confirm with ARC that the intended rim's drilling matches the hub's lacing direction, because a mismatch here surfaces only at the truing stand.
The Carbon-Spoke Interface: 4.2mm and Standard Spoke Choice
Carbon-spoke wheels live or die on the spoke-to-hub connection. The MT-105F/R uses a dedicated 4.2mm interface designed for compatible round-head carbon bladed spokes, with Hongji Weiye B-type spokes specified as the standard configuration. That is a useful starting point for an OEM programme: it gives the buyer a known baseline spoke rather than a blank specification, and it tells the engineering team which spoke head geometry the flange slot is cut for.
The 4.2mm dimension is the kind of figure that should be checked against the actual spoke drawing before sampling, not treated as interchangeable with other carbon blade interfaces. Round-head carbon bladed spokes from different sources can vary in head thickness, slot width and bend radius even when the nominal interface sounds similar. A buyer planning to use a different spoke supplier should send the spoke specification to ARC and confirm compatibility at the quotation stage. Keeping the standard Hongji Weiye B-type for first samples removes one variable, so any tension or ride feedback in the sample wheel can be attributed to the hub and build rather than to an unproven spoke interface.
Ratchet, Bearings and Materials: What You Are Actually Specifying
Three specification layers sit behind the MT-105F/R, and each one carries a different cost and performance implication.
The drive mechanism is ARC's patented one-piece ratchet architecture, offered in 36T and 54T. The choice is a trade-off buyers should make deliberately: a higher tooth count gives quicker engagement, which matters for criterium-style acceleration and technical road riding, while the lower count is the more conventional pick where the priority is a simpler, well-understood drive feel. Neither option should be presented as universally better; the right answer depends on the rider profile the wheelset is aimed at.
Bearings are offered in S&S steel, ENDURO and CeramicSpeed options. This is the clearest cost-versus-rolling-performance decision in the specification, and it should be matched to the price tier of the wheelset rather than defaulted to the most expensive choice. A brand building a value-oriented carbon wheelset and a brand building a flagship race wheel can use the same hub platform and differentiate at the bearing line.
The structure combines a forged AL6061-T6 aluminium hub shell with high-strength AL7075 axles, freehub body and end caps. ARC lists a complete hub set weight of approximately 328.5g, split as 92.4g front and 236.1g rear. For a carbon-spoke road disc programme, that is a figure worth putting beside the rim and spoke weights early, because the hub set is light enough that the build's weight story will be driven mainly by rim and spoke selection.
Axle, Brake and Freehub Standards to Confirm Before Sampling
The MT-105F/R uses a Center Lock disc interface with 12×100mm front and 12×142mm rear thru-axle spacing—the current mainstream road disc standard, and the one most carbon road frames and forks are designed around. Confirming it against the target frame and fork drawings is still worthwhile, particularly for brands building across several frame platforms.
Freehub support covers Shimano HG, Road Micro Spline, SRAM XDR, Campagnolo N3W and Campagnolo 11/12-speed. That breadth lets one hub platform serve multiple drivetrain groups, but it also means the freehub must be locked per SKU before ordering. A pre-sample checklist for OEM buyers would include: rim drilling and 2:1 rear pattern match; spoke model and 4.2mm interface compatibility; ratchet tooth count; bearing tier; freehub standard per drivetrain variant; axle spacing against frame and fork; and Center Lock rotor compatibility. Rotor lockring clearance and bearing preload procedure are also worth confirming with ARC's technical team so the first sample build reflects production intent.
Working with ARC on a Custom Hub Program
The MT-105F/R is a specification platform, not a single fixed SKU, and that is where ARC's role becomes relevant. Taicang Xiangyue Sports Equipment Co., Ltd. (ARC) has manufactured high-performance bicycle hubs in Taicang, Jiangsu since 2013, with CNC machining, precision manufacturing and quality control supporting OEM and ODM work for bicycle brands, wheel manufacturers and distributors. For a carbon-spoke road disc wheelset programme, that means the ratchet, bearing, freehub and interface choices above can be fixed as a defined configuration rather than assembled from a catalogue.
For buyers evaluating this hub set, the practical next step is a focused sample request: state the rim, the intended spoke (or confirm Hongji Weiye B-type), the ratchet and bearing tier, the freehub standard and the axle spacing, and ask ARC to confirm compatibility before a sample wheel is built. ARC's MT-105F/R 18/21H Carbon-Spoke Center Lock Road Hub Set is a sensible starting point for lightweight, high-performance road disc carbon wheel builds where an asymmetric 2:1 layout and a defined carbon-spoke interface are part of the design brief—and a hub platform worth putting on the shortlist for any OEM programme that needs those characteristics locked down before sampling.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China