ARC RT-035FCB/RCB

ARC RT-035FCB/RCB Carbon Straight-Pull Road Hub Set: Specifications for Lightweight Rim-Brake Builds

14 min read
On this page 6 sections

What the RT-035FCB/RCB Is Designed For

The ARC RT-035FCB/RCB is not a general-purpose hub that happens to appear on a road wheel. It is a hubset specified around one job: lightweight road wheels built for rim brakes. That distinction matters at the procurement stage, because rim-brake road frames impose a different set of constraints than disc-brake platforms—narrower flange spacing, no rotor mounts, and a stronger premium on gram count and spoke geometry, since the wheel carries braking load through the rim rather than a rotor and caliper at the hub.

Buyers working on rim-brake road wheelsets therefore tend to evaluate hubs on three fronts at once: whether the drilling and spoke layout support the rim they have chosen, whether the freehub and ratchet configuration matches the groupset, and whether the finished wheel can stay inside a competitive weight target. The RT-035FCB/RCB addresses all three within a single defined specification, which is why it is worth examining as a candidate for a lightweight rim-brake program rather than as an afterthought to a disc-brake range.

Drilling and Straight-Pull Spoke Layouts

The hubset uses a 20-hole front and 24-hole rear straight-pull configuration. This is a familiar ratio for road wheels aiming at low weight without abandoning structural margin at the rear, where drive torque and the rider's weight concentrate. The 20H front suits lower-spoke-count front lacing, while the 24H rear leaves room for a properly tensioned drive-side pattern.

Its 20H front and 24H rear straight-pull configuration supports 1:1 and 2:1 spoke layouts. The choice between them is not cosmetic. A 1:1 layout distributes spokes evenly between left and right flanges, which tends to simplify lacing and produce a more symmetrical build; a 2:1 layout biases spoke count toward the drive side or the higher-tension side, which builders often use to balance tension where dish would otherwise leave one side noticeably looser. Straight-pull spokes remove the J-bend entirely, which eliminates the bend flex point and generally gives a cleaner, more direct load path from hub to rim.

For a product manager matching the hubset to a specific rim, the practical sequence is to confirm the rim's spoke count and recommended lacing first, then verify that the chosen 1:1 or 2:1 pattern is achievable with the rim's drilling and the intended spoke lengths. The RT-035FCB/RCB supports both, which gives a wheel program more than one route to the same hubset—useful when one rim in a range calls for a tension-biased build and another does not.

Ratchet Options and Freehub Compatibility

The drive mechanism is offered with a 36T or 54T ratchet. In general terms, a higher tooth count reduces the rotation between engagement points, which riders typically associate with quicker pickup; a lower count gives fewer, larger engagement interfaces. Neither is inherently better, and the right choice depends on the rider profile the wheelset is aimed at and on how the brand wants to position engagement feel. Both options sit within a patented one-piece ratchet architecture, a design detail that buyers should note when comparing hubs, since it describes how the ratchet is constructed rather than simply how many teeth it has.

Freehub compatibility covers Shimano HG and SRAM XDR. This is one of the first things to confirm in a rim-brake road program, because the wheelset must be orderable against the groupsets the brand actually sells. A hub that only covers one standard forces either a second SKU or a compromised spec sheet. Offering both HG and XDR within the same hubset lets a brand build one wheel platform and configure it at the freehub level, which simplifies inventory planning and reduces the number of distinct build sheets a workshop has to manage.

Buyers should still verify the exact freehub body configuration against their drivetrain plan before committing to a production run, and should treat engagement feel as something to validate on sample rather than infer from tooth count alone.

Materials, Weight and Build Considerations

The hub shell combines AL6061-T6 aluminum with a carbon tube, and the hubset uses high-strength AL7075 aluminum components at the loaded interfaces. This is a sensible materials split for a lightweight road hub: the aluminum shell provides the machined precision and thread integrity that flanges and bearing seats require, the carbon tube contributes to weight reduction, and AL7075 is used where strength-to-weight matters most.

The complete hubset weighs approximately 358.3g. For a rim-brake road wheelset, that figure is worth putting in context early in the planning process, because hub weight is fixed mass at the center of the wheel and is not offset by rim or spoke choices later. A brand targeting a specific complete-wheel weight can subtract this figure from its budget before selecting rim and spokes, which is a more reliable way to plan than adjusting at the end.

Two cautions apply. First, the stated weight is for the complete hubset and should be confirmed for the exact configuration—ratchet option and freehub standard—being ordered. Second, hub weight is only one input into wheel performance; spoke count, rim choice, lacing pattern and build quality all influence stiffness and durability, so the hubset should be evaluated as part of a specified build rather than on its own. A sensible validation step is to request samples, build them to the intended rim and lacing, and measure tension balance and ride feel before locking a production specification.

Working With ARC on Road Hub Supply

ARC, based in Taicang, Jiangsu, China and founded in 2013, manufactures bicycle hubs and provides OEM and ODM solutions for bicycle brands, wheel manufacturers and distributors across road, MTB, gravel and e-bike applications. The RT-035FCB/RCB sits within that road hub range as a defined rim-brake option, and its specification—carbon and AL6061-T6 shell, AL7075 components, 20H/24H straight-pull drilling, 1:1 and 2:1 layout support, 36T or 54T one-piece ratchet, HG and XDR freehubs—gives a purchasing team a concrete basis for a first evaluation.

For brands assembling a lightweight rim-brake wheelset program, the hubset is worth including on a shortlist and assessing against the specific rim, groupset and weight target in question. The most useful next step is to confirm the intended ratchet and freehub configuration, request samples for a build test, and review the specification against the finished-wheel requirements before moving to production discussions.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China