Carbon-Spoke Hub Set

Building Lightweight MTB Wheels with a 24H Carbon-Spoke Hub Set: Common Pitfalls

17 min read
On this page 6 sections

Building a genuinely light mountain bike wheelset around a 24-hole carbon-spoke hub set is less about shaving grams from a spreadsheet and more about avoiding a handful of specification and process errors that quietly cancel the weight advantage. Most failures in this category do not come from a defective hub or a bad spoke; they come from mismatches decided long before the first spoke is threaded. The checks below are the ones worth running before any tooling or production commitment is made, and they apply equally to in-house wheel builders and to brands commissioning a wheelset program.

Pitfall 1: Treating 24H as a universal lightweight answer

The first mistake is assuming that dropping to 24 spokes automatically makes a wheel lighter and faster. A 24H layout changes how load is distributed around the rim and how much work each spoke does, so it only pays off when the rider profile, rim stiffness and intended terrain are aligned with it. Cross-country and marathon use, lighter riders and smoother courses tolerate lower spoke counts well; aggressive trail riding, heavier riders or frequent rock strikes push the same 24H layout into a much narrower margin.

The practical audit is to define the design envelope first — rider weight range, discipline, tire volume, expected impact load — and only then confirm that 24 holes front and rear is the right count. Building a 24H wheel and compensating with a heavier rim usually produces a wheelset that is neither light nor robust. A hub set designed around the 24H configuration from the outset avoids this partly, because the flange layout and spoke angles are already planned for that count rather than adapted from a 28H or 32H platform.

Pitfall 2: Mismatching carbon spokes to hub flange geometry

Carbon spokes are not a drop-in replacement for steel spokes. Their end fittings, required hole clearance and acceptable bend angle differ, and a hub flange designed for metal spokes can force the carbon spoke into a poor entry angle or leave insufficient material around the hole. The result is not an immediate failure but a stress concentration that shows up later as spoke damage at the head or elongation of the flange holes.

Before committing, verify three things against the actual hub drawing: the spoke hole diameter and chamfer suit the carbon spoke fitting, the flange offset places the spoke path within the spoke maker's permitted angle, and the flange thickness supports the load without deformation. It is also worth confirming lacing options — a 24H hub may be built two-cross or three-cross depending on flange diameter, and the choice affects both spoke length and the angle at the rim. ARC's MT-116F/R 24H Carbon-Spoke Boost Center Lock MTB Hub Set is engineered specifically for carbon-spoke applications, with a 24H front and rear configuration that supports balanced spoke layouts, which removes some of this guesswork at the interface level. What it does not remove is the need to check the specific carbon spoke brand's fitting dimensions against the flange drawing.

Pitfall 3: Building to tension numbers copied from metal-spoke wheels

Tension targets are the most commonly transplanted figure in wheel building, and the most damaging. Steel spokes tolerate a broad tension window; carbon spokes have their own recommended range set by the spoke manufacturer, and exceeding it can damage the spoke or the rim bed, while falling short produces a wheel that feels vague and loses true quickly. Copying a 1,200 N target from a steel build onto a carbon-spoke wheel is a specification error, not a tuning choice.

Build practice needs to change alongside the number. Carbon spokes transmit tension changes more directly, so bring the wheel up in smaller increments and check balance between drive and non-drive sides more often. With only 24 spokes, each one carries a larger share of the total, so a single outlier tension matters more than it would in a 32H build. Use a calibrated tensiometer matched to the carbon spoke's cross-section, record tension at several stages, and verify radial and lateral true after stress-relieving rather than before. Treat the spoke maker's published range as the ceiling, and treat even tension distribution — not maximum average tension — as the quality target.

Pitfall 4: Overlooking frame, rotor and freehub compatibility

Specification errors at the frame interface are expensive because they surface after the wheels are built. Three items deserve confirmation in writing before ordering: the dropout standard, the rotor mount and the freehub body.

Boost spacing is the first. A hub set built to 15×110mm front and 12×148mm rear will not fit a non-Boost frame, and converting afterwards usually means new end caps or a new hub. Center Lock is the second — it commits the build to Center Lock rotors, so any plan to run six-bolt rotors needs to be resolved at specification stage, not at assembly. The third is freehub standard, where Shimano HG, Micro Spline and SRAM XD are not interchangeable and each implies a different cassette family and drivetrain ecosystem.

Engagement configuration belongs in the same conversation. Ratchet systems are commonly offered in different tooth counts, and the choice affects how the bike feels under pedaling load rather than how light the hub is. The MT-116F/R hub set addresses these variables directly: Boost 15×110mm front and 12×148mm rear spacing, a Center Lock disc interface, compatibility with Shimano HG, Micro Spline and SRAM XD freehub standards, and a 36T or 54T ratchet system built on ARC's patented one-piece ratchet architecture. For a wheelset brand, that combination means the hub specification can be fixed against the frames and drivetrains already in the catalog instead of being renegotiated mid-program.

Pitfall 5: Skipping pre-production validation

The final and most costly pitfall is moving from drawing to production without a physical build. Spoke length calculations are only as good as the inputs, and a 24H carbon-spoke wheel has less tolerance for a millimetre of error than a conventional build. A single sample wheel, built and measured, catches most of the problems that would otherwise appear across an entire batch.

A workable validation sequence looks like this: confirm hub dimensions and flange geometry against the drawing; calculate spoke length for the chosen lacing and verify against the physical hub; build one front and one rear wheel to the spoke maker's tension range; measure final weight, dish, and both radial and lateral deviation; then ride or lab-test to the intended duty cycle before releasing the specification. Only after that sample passes should tooling, spoke orders or production quantities be committed.

This is also the stage where OEM and ODM support earns its place. ARC provides OEM and ODM solutions for global bicycle brands, wheel manufacturers and distributors, which matters when a hub specification has to be adapted to a particular wheelset program rather than taken off the shelf. The hub shell is machined from AL6061-T6 aluminum with an AL7075 axle, freehub body and end caps, and the set weighs approximately 340.1g — figures a builder can put directly into the weight budget and check against the sample. Because ARC manufactures hubs as its core business, engineering questions about flange geometry or freehub configuration can be resolved with the people who control the tolerances, not through a third party.

The common thread across all five pitfalls is that the hub set is the deciding interface in a lightweight 24H carbon-spoke build, not a component selected at the end. Spoke count, flange geometry, tension practice, frame and drivetrain compatibility, and sample validation all converge on that one part. Teams planning a lightweight MTB wheelset program will find the MT-116F/R a sensible starting point for evaluation precisely because its 24H carbon-spoke configuration, Boost spacing, Center Lock interface and multi-standard freehub options let those five checks be settled against a defined specification rather than discovered during assembly.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China