Carbon spokes can be one of the most rewarding weight-saving choices in a road disc wheelset, but they are also far less forgiving than steel spokes when the hub interface is not matched correctly. Before tension balance, stiffness targets or bearing selection enter the conversation, a wheel builder has to answer a simpler question: will the spoke physically seat in this hub, and will it stay seated under load? That is why spoke hole geometry and T-head seat design should be treated as the first compatibility checkpoint in any carbon road disc hub specification, including the ARC MT-116F/R hub set, which is built around a dedicated carbon-spoke interface.
Why the Spoke Hole Is the First Compatibility Check
A steel J-bend or straight-pull spoke tolerates a certain amount of clearance at the hub. The wire is ductile, the head can conform slightly, and small dimensional mismatches are usually absorbed by the build. A carbon spoke offers almost none of that forgiveness. Its load path runs from the spoke shaft into a moulded T-head, and that head must sit against a matching seat with enough contact area to spread the load without point-loading the composite.
This is why the spoke hole is not just a drilling detail. Its shape, its seat angle and the width of the bearing surface all determine whether the spoke head sits flush or rocks. If the seat is too narrow, contact pressure concentrates on a small band of the T-head; if the seat is too wide or the hole profile is wrong, the head can shift under pedalling and braking loads. Either condition undermines the very stiffness and durability the carbon spoke was chosen to deliver.
For buyers, the practical consequence is that hub selection should begin with the spoke interface rather than being retrofitted to it. A hub drilled for a generic round spoke shank is not automatically suitable for a T-head carbon spoke, even if the hole diameter happens to match. The MT-116F/R addresses this by using dedicated T-head spoke holes rather than a general-purpose spoke bed, which is the specific design decision this compatibility discussion turns on.
T-Head Seats and Spoke Width: Reading the Fit Window
The second variable is width. Carbon spokes are not a single standard, and the T-head dimensions vary between suppliers. A hub that suits one spoke family may not suit another, so the useful specification is not a single number but a defined fit window.
The MT-116F/R is designed around a T-head interface that accommodates compatible carbon spokes in 3.3 mm and 5.2 mm widths. Those two figures matter because they represent the practical range a wheel builder needs to check against the actual spoke on the bench. A 3.3 mm spoke and a 5.2 mm spoke place different demands on seat width and contact area, and a hub intended for one should not be assumed to fit the other without verification.
When reading the fit window, buyers should confirm three things together rather than in isolation:
- Spoke head width against the hub's stated compatible widths, not against the hole diameter alone.
- Seat contact geometry, meaning how much of the T-head actually bears on the hub surface once the spoke is under tension.
- Spoke supplier tolerances, since the same nominal width can differ slightly between manufacturers and moulds.
A spoke that fits loosely at the seat may still build, but it will be harder to hold tension consistently across the wheel. A spoke that fits too tightly can be difficult to seat fully, which risks an incomplete contact patch. The 3.3 mm and 5.2 mm range on the MT-116F/R gives builders a clear window to work within, but the matching step against the chosen spoke remains the buyer's responsibility before sampling.
1:1 Versus 2:1: What the Layout Changes
Once fit is settled, the next decision is layout. The MT-116F/R interface supports both 1:1 and 2:1 spoke configurations, and the choice is not cosmetic. It changes how spoke count is distributed between the two flanges and, with it, the tension balance and stiffness behaviour of the finished wheel.
In a 1:1 layout, each side of the hub carries an equal share of the spokes. Tension is distributed more evenly between left and right, which can simplify the build and suit riders or programs looking for a balanced, predictable feel. In a 2:1 layout, the spoke count is weighted toward one side, typically to compensate for the asymmetric dish created by the cassette and disc brake. The aim is to bring the two sides closer to comparable tension despite the offset, which can support a stiffer, more efficient transfer of drive and braking loads.
Neither layout is universally better. A 1:1 build may be preferable where even tension distribution and straightforward spoke availability matter most; a 2:1 build may be preferable where the dish is pronounced and the builder wants to reduce the tension disparity between sides. The right answer depends on rim depth and offset, rider weight and intended use, and the target stiffness of the wheelset. What the MT-116F/R interface provides is the freedom to choose between the two rather than being locked into one pattern at the hub specification stage — a genuine advantage when a single hub platform has to serve several wheelset models.
Specifying the Rest of the Hub Around the Spoke Interface
The spoke interface is the first checkpoint, not the only one. A carbon road disc hub specification only holds together when the surrounding dimensions are confirmed at the same time, because they constrain which lacing patterns and spoke lengths are even possible.
On the MT-116F/R, the spoke hole count is 20H front and 21H rear, which immediately sets limits on the lacing pattern and must be reconciled with the chosen 1:1 or 2:1 configuration before spokes are ordered. Axle spacing is 12×100 mm front and 12×142 mm rear thru-axle, matching current road disc framesets. The Center Lock disc mount and the freehub standard — Shimano HG, Road Micro Spline, SRAM XDR, Campagnolo N3W or Campagnolo 11/12-speed — need to be confirmed against the drivetrain and rotor choice. Bearing options include S&S steel, ENDURO and CeramicSpeed, and the ratchet architecture is a one-piece design available in 36T and 54T.
These details are worth reading together because they interact. A one-piece ratchet and AL6061-T6 shell, paired with AL7075 axles and freehub body, describe how load moves from the spoke bed into the hub and then into the frame. The complete hub set is quoted at approximately 281.1 g, which is the kind of figure that makes sense only once the spoke interface and bearing choice are fixed. ARC's background in OEM and ODM hub development for wheelset brands and distributors is relevant here, because specification-stage buyers often need the interface, axle and freehub variables confirmed as a single package rather than sourced piecemeal.
What to Confirm Before Ordering Samples
For OEM and wheelset buyers, the technical discussion converts into a short verification list. Working through it before requesting samples avoids the most common carbon-spoke mismatch, which is discovered only at the build stage.
- Match the spoke to the stated width window. Confirm the chosen carbon spoke falls within the 3.3 mm and 5.2 mm widths the MT-116F/R T-head holes are designed to accept, and check the spoke supplier's actual head dimensions rather than the nominal figure.
- Confirm seat contact. Ask how the T-head seats against the hub under tension and verify that contact is full and even, not concentrated on an edge.
- Decide the layout against the rim. Choose 1:1 or 2:1 based on rim offset, dish and target stiffness, then check that the 20H front and 21H rear hole counts support the intended pattern and spoke lengths.
- Lock the surrounding specification. Confirm 12×100 mm and 12×142 mm thru-axle spacing, Center Lock mount, freehub standard, ratchet tooth count and bearing option in the same review.
- Sample and build one wheel first. Validate tension retention and seat condition on a built sample before committing a production order, since fit and tension behaviour are best judged on a finished wheel rather than a drawing.
For wheel builders and purchasing managers specifying a carbon road disc hub, the MT-116F/R is a sensible candidate to put on the evaluation list precisely because its dedicated T-head interface, defined 3.3 mm and 5.2 mm spoke width window, and support for both 1:1 and 2:1 layouts answer the compatibility questions this article opened with. The next step is straightforward: take the spoke you intend to use, check it against those interface details, and let a built sample confirm the fit before the specification is frozen.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China