Wheel builders targeting a lightweight rim-brake wheelset usually run out of places to save grams long before they run out of ideas. Rims can only get so light before braking heat and durability become concerns; spokes and nipples have a floor; and rim-brake frames and calipers have their own fixed constraints. The hub set sits at the center of that problem. It determines how much material is devoted to the shell, how spoke loads are distributed, and how much rotating mass sits at the second-most influential radius on the wheel. For a build where every component has to justify its weight, the hub is rarely a neutral choice — it either opens up the spoke and rim budget or consumes it.
The ARC RT-035FCB/RCB Carbon Straight-Pull Road Hub Set is a useful case study because it was designed around exactly this trade-off. The question for product managers and OEM engineers is not simply whether it is light, but whether its material mix, drilling, ratchet architecture, and freehub options line up with a specific rim-brake program. Answering that requires looking at each specification on its own terms and separating what the documentation confirms from what only sample testing can settle.
Why Rim-Brake Weight Targets Start at the Hub
A rim-brake road wheelset carries weight in the rim that a disc-brake wheel does not, because the brake track has to absorb friction heat and the caliper acts on the rim itself. That pushes builders toward shallow, lighter rims — and then transfers structural demands back to the hub and spoke system. Fewer or lighter spokes, a narrower flange spacing, and a light shell can all save grams, but each one changes how tension is shared between the left and right sides of the rear wheel.
Rotating mass also behaves differently from static mass. A gram removed from the hub shell is worth more than a gram removed from the frame; a gram removed from the hub flange area has a shorter moment arm than one removed from the rim, but it also reduces the stiffness of the anchor point that spokes pull against. Lightweight hub shells therefore need to be evaluated on two axes at once: weight and the rigidity of the spoke-anchoring structure.
Straight-pull designs enter this conversation because they remove the J-bend and the spoke elbow, which is one of the historically weak points in a wheel. A straight-pull spoke runs directly from the flange to the rim, which can produce a cleaner load path and easier tension control during building — provided the flange geometry and drilling suit the intended lacing pattern. For a light rim-brake build, that combination of material savings and predictable tensioning is the real argument, not weight alone.
What the RT-035FCB/RCB Actually Specifies
The starting point for any procurement conversation is a clear statement of what the product is. According to the product documentation, the RT-035FCB/RCB is a carbon straight-pull road hub set designed for lightweight road rim-brake wheel builds. It combines an AL6061-T6 aluminum and carbon tube hub shell with high-strength AL7075 aluminum components. The front uses 20H straight-pull drilling and the rear 24H, and the configuration supports both 1:1 and 2:1 spoke layouts. It is available with a 36T or 54T ratchet system built on a patented one-piece ratchet architecture, is compatible with Shimano HG and SRAM XDR freehub standards, and the complete hub set weighs approximately 358.3 grams.
ARC RT-035FCB/RCB Carbon Straight-Pull Road Hub Set
Two points about that specification deserve emphasis for buyers. First, the material split is not an afterthought: using a carbon tube within an AL6061-T6 shell, paired with AL7075 aluminum in the loaded components, is a deliberate attempt to place lightweight material where it reduces mass and stronger alloy where fasteners and ratchet interfaces need wear resistance and strength. Second, the 358.3 g figure is a hubset weight and should be treated as such in any wheelset calculation — it does not by itself describe spoke, rim, or complete-wheel mass, and it should not be read as a performance guarantee.
What the documentation does not state is equally important. It does not quantify stiffness, bearing life, tension balance, or fatigue behavior. Those are sample-level questions, and a credible buyer should treat them that way.
Spoke Drilling and Layout: 20H/24H Straight-Pull in Practice
The 20H front and 24H rear drilling is a conventional and sensible starting point for a lightweight rim-brake road build. A 20-spoke front keeps the front wheel light and is generally adequate when the rim is stiff enough to share load across fewer anchor points; a 24-spoke rear acknowledges that the rear wheel carries more vertical load and, more importantly, must cope with the dish created by the cassette and the asymmetric tension that follows.
That is where the 1:1 versus 2:1 layout choice becomes a real engineering decision rather than a checkbox. In a 2:1 layout, more spokes are assigned to the side of the wheel that carries higher tension — typically the drive side of the rear hub — which can help equalize tension between the two flanges and reduce the tendency for the lower-tension side to go slack under load. A 1:1 layout distributes spokes evenly and can be simpler to build and true. Neither is inherently better; the right answer depends on the rim's stiffness, the intended spoke count, and the builder's tension targets.
Because the RT-035FCB/RCB supports both patterns, wheelset teams have room to match the hub to the rim rather than the reverse. The practical recommendation is to decide the lacing pattern before sampling, then request that the sample be built with the exact drilling and spoke specification intended for production. Testing a 2:1 sample when production will run 1:1 tells the buyer very little about the real wheel. Straight-pull configurations also reward builders who use a consistent spoke length and tensioning sequence; the absence of an elbow means the tension reading reflects the spoke and rim interface more directly, so build records become a more useful quality signal across a production run.
Ratchet and Freehub Choices to Lock Down Before Sampling
The drive mechanism is the part of a hub set that most often gets deferred until late in a program, and it is also the part most expensive to change afterward. The RT-035FCB/RCB offers a 36T or 54T ratchet on a patented one-piece ratchet architecture. The higher tooth count generally corresponds to a shorter engagement angle and a different engagement feel; the lower count is the more conventional choice. Which one belongs in a given wheelset is a question of intended rider feedback and internal design priorities, not a simple upgrade ladder, and engagement feel should be judged on samples rather than inferred from tooth count alone.
Freehub standard is the sharper compatibility decision. The hub set is offered in Shimano HG and SRAM XDR, and these are not interchangeable at the build stage: the choice has to match the cassette the wheelset will ship with and the frame spacing and drivetrain plan of the target bike. A wheelset brand serving both Shimano and SRAM road customers may need both versions qualified, which has implications for stock, documentation, and service parts. Getting this wrong late in a program means reworking drawings, relabeling SKUs, and re-testing.
For ARC, the OEM/ODM side of the business is built around exactly this kind of configuration alignment. Founded in 2013 and based in Taicang, Jiangsu, China, ARC specializes in the research, development, manufacturing, and customization of high-performance bicycle hubs and provides OEM and ODM solutions for global bicycle brands, wheel manufacturers, and distributors. Its work spans mountain bikes, road bikes, gravel bikes, and e-bikes, with CNC machining, precision manufacturing, and quality control systems supporting those programs. For a rim-brake road hubset, that means drilling, freehub, and ratchet choices can be discussed as part of a defined build program rather than selected from a fixed catalog.
Before sampling, buyers should put the following in writing: the exact ratchet tooth count, the freehub standard and version, the drilling and intended lacing pattern, the spoke type and length, the axle configuration required by the frame, and the acceptance criteria the sample will be judged against — including tension balance, true, bearing feel, and engagement consistency. Any tolerances not documented by ARC should be requested explicitly.
Working with ARC on OEM/ODM Hub Programs
Sample approval is a milestone, not the end of the sourcing decision. The questions that follow concern consistency: whether the second batch matches the first, whether the ratchet interface and freehub body hold their fit over production volume, and whether documentation keeps pace with configuration changes. These are the questions that determine whether a lightweight hubset remains a reliable part of a wheelset line or becomes a recurring quality issue.
The RT-035FCB/RCB's specification set makes it a reasonable candidate for rim-brake wheelset programs that need a light hub platform with genuine configuration flexibility. The aluminum-and-carbon shell, the AL7075 loaded components, the 20H/24H straight-pull drilling with dual layout support, the ratchet options, and the Shimano HG / SRAM XDR coverage together describe a hubset that can be adapted to different rim-brake builds without changing the underlying platform. That is the practical value for a wheelset brand: one hub architecture to qualify across several SKUs.
The other half of that value is the manufacturing relationship. A hub manufacturer that handles both development and production in-house can respond to a requested drilling or freehub change within the same program, rather than forcing a buyer to re-source. ARC's combination of in-house R&D, CNC machining, customization, and OEM/ODM support is directly relevant here — not as a promise of specific lead times or volumes, which should be confirmed project by project, but as the structural reason a configuration-led hub program is workable in the first place.
For teams evaluating the RT-035FCB/RCB, the sensible next step is to request samples built to the intended production specification, with the ratchet count, freehub standard, and spoke drilling fixed in advance, and to define the acceptance criteria before the samples arrive. Wheelset brands, OEM wheel-building engineers, and component purchasing managers with a lightweight rim-brake program will find in this hub set a credible platform to evaluate — one whose real performance will be established by the samples and the build records, not by the specification sheet alone.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China