Center Lock Road Hub

Center Lock Road Hub Sets: AL6061-T6 Shell, AL7075 Axle, Freehub Body and End Caps

11 min read
On this page 5 sections

Road and gravel wheelset programs that specify Center Lock disc hubs face a familiar trade-off: a light hub that flexes under load, or a stiff one that adds rotating mass. The ARC MT-092F/R 21H Round-Head Carbon-Spoke Center Lock Road Hub Set addresses that tension with a deliberate material split — an AL6061-T6 shell paired with an AL7075 axle, freehub body and end caps — plus a patented one-piece ratchet and a 21H 2:1 spoke layout. For product managers and engineers scoping a carbon-spoke disc wheel build, understanding why each part uses the alloy it does is the starting point for a precise sample request.

What the Four-Part Hub Construction Actually Means

The four named components are not interchangeable aluminum parts. Each alloy choice reflects the load path and manufacturing method of that specific part.

The hub shell is made from AL6061-T6. This alloy is widely used for hub shells because it machines cleanly, welds and heat-treats predictably, and offers good fatigue resistance at moderate cost — a sensible fit for a CNC-machined shell that must hold bearing bores and spoke flanges in alignment.

The axle, freehub body and end caps are made from AL7075. In its heat-treated condition, AL7075 is significantly stronger than AL6061, which matters for the axle (a thin-walled, high-stress tube carrying rider load between the dropouts) and for the freehub body (which transmits drive torque through the ratchet interface). End caps benefit from the same higher-strength alloy because they are thin, load-bearing interfaces that seat in the frame dropouts.

The result is a lightweight and durable construction in which each part is matched to its job rather than using one alloy throughout. For buyers, this is a specification to read literally: when a supplier lists "AL7075 axle and freehub body," that is a strength decision on the highest-stress parts, not a marketing label.

Freehub Standards, Ratchet Options and Axle Spacing to Confirm

Three specification groups determine whether this hub set fits a given build.

Freehub standards. The ARC MT-092F/R is compatible with Shimano HG, Road Micro Spline (MS), SRAM XDR, Campagnolo N3W and Campagnolo 11/12-speed freehub bodies. This covers the common road and gravel drivetrain families, but the buyer must name the standard at sampling — a Campagnolo build and a SRAM XDR build require different freehub bodies from the same hub platform.

Ratchet options. The hub uses a 36T or 54T ratchet system built on ARC's patented one-piece ratchet architecture. The choice trades engagement points against other characteristics the buyer must evaluate on their own drivetrain and riding profile; it should be fixed in the specification rather than left open.

Axle spacing. The set uses 12×100mm front and 12×142mm rear thru-axle spacing — the modern road/gravel disc standard. Confirm this against the frame and fork before sampling, since it cannot be adapted in the hub itself.

The stated weight is approximately 357.7g for the set. Treat that as a published specification to verify on samples, not as a performance guarantee, since build weight also depends on bearings, freehub body choice and spoke-hole configuration.

Spoke Holes and Carbon-Spoke Compatibility

The hub set uses a 21H front and rear 2:1 spoke configuration. In a 2:1 layout, one side of the flange carries twice the spokes of the other, which helps balance spoke tension between the drive and non-drive sides — a particular concern on disc-brake wheels where the brake loads the hub asymmetrically.

The drilling is round-head, and it is dedicated to Hongji Weiye Type B and Type C carbon spokes. This is a hard compatibility boundary, not a broad "carbon-spoke compatible" claim. Builders planning a different carbon spoke brand should not assume fit; the hole geometry and head seat are specified for those two spoke types. Confirm spoke availability and length calculations with the wheel builder before committing to the 21H drilling.

Specifying the MT-092F/R for OEM and ODM Programs

For a wheelset brand or complete-bike OEM, this hub set fits programs that combine Center Lock disc brakes, carbon spokes and thru-axle road or gravel frames. ARC manufactures this model with a defined material split and offers OEM and ODM hub customization from its Taicang facility, with engineering and CNC machining support for global bicycle brands, wheel manufacturers and distributors across road, MTB, gravel and e-bike categories.

When preparing a sample request, document four items precisely: the freehub standard (HG, Road MS, XDR, N3W or Campagnolo 11/12-speed), the ratchet option (36T or 54T), the 21H 2:1 round-head drilling for Hongji Weiye Type B or Type C carbon spokes, and the 12×100mm / 12×142mm spacing. Adding the intended rim, spoke brand and target build weight lets ARC's team confirm whether the MT-092F/R platform matches the program before tooling or volume commitments.

If your next carbon-spoke disc wheelset depends on a hub that separates its alloys by function — AL6061-T6 shell, AL7075 axle, freehub body and end caps — the ARC MT-092F/R is worth including in the sample evaluation, with the freehub standard, ratchet and spoke-hole specification confirmed up front.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China