The most common mistakes when matching freehub standards and axle spacing on MTB hub sets come from treating two unrelated specification fields as one decision. The cassette interface — Shimano HG, Micro Spline, or SRAM XD — determines which drivetrain the hub can accept. The axle spacing determines whether the hub fits the frame. Neither choice follows automatically from the other, and neither can be safely inferred from the other. Buyers who conflate the two often approve a hub specification that looks correct on a summary line but fails at wheel build or frame assembly. Working through the checkpoints below before committing to a bulk order or custom spec is the simplest way to avoid that outcome.
Why These Two Fields Get Confused
Both fields appear in the same narrow band of a hub specification sheet, and both are frequently quoted in shorthand. A line such as "9×100mm front, 10×135mm rear" describes over-locknut distance and fixing method only. A line such as "HG / Micro Spline / XD compatible" describes the freehub body interface only. When these are compressed into a single product title or a short quotation, they read as one combined attribute rather than two independent ones.
The confusion is reinforced by how specifications are commonly discussed. Drivetrain conversations tend to start with cassette choice and then jump to "what hub do I need," while frame conversations start with dropout width and then ask the same question. Both paths arrive at the hub from different directions, and a buyer under time pressure may assume the hub supplier has already reconciled them. In practice, freehub standard and axle spacing are selected independently and must be confirmed independently on the written specification.
There is also a practical reason the two are easy to mix up: many MTB hub platforms are offered in several spacing and freehub variants, so the same model name can cover configurations that are not interchangeable. Unless the exact combination is written down, a model reference alone does not identify what will be delivered.
Mistake 1: Assuming the Freehub Standard Follows the Axle Spacing
The freehub body is a drivetrain-side component. Its standard — HG, Micro Spline, or XD — must match the cassette the bike will run, and that requirement is set by the groupset and gearing plan, not by the frame. Axle spacing and fixing method are frame-fit decisions. A 10×135mm quick-release rear spacing says nothing about whether the hub is supplied with an HG, Micro Spline, or XD freehub body, and a hub quoted with a particular freehub standard says nothing about its dropout width.
This is where specification errors begin. A buyer specifying a 10×135mm quick-release rear hub for an entry-level or recreational build might assume that spacing implies a particular cassette interface, when in fact the freehub standard has to be stated separately. Suppliers that offer several freehub options on the same hub platform can legitimately ship different bodies against the same spacing figure, so the freehub standard must always be written as its own line item.
The verified specification on the ARC MT-001FG/003RC hub set illustrates how the two fields sit side by side without depending on each other. As documented for that model, it is compatible with Shimano HG, Micro Spline and SRAM XD freehub standards, and it features 9×100mm front and 10×135mm rear quick-release spacing. The freehub compatibility and the quick-release spacing are separate statements describing separate interfaces; a buyer reading only one of them has half the specification.
Mistake 2: Specifying Only One End of the Hub Set
Front and rear hubs are separate fit problems. The front hub must suit the fork dropout, and the rear hub must suit the frame dropout, and the two widths are not derived from one another. Quoting only a rear figure, or only a front figure, leaves half the set unverified — and a hub set ordered on that basis can arrive with one end that does not fit the intended build.
The pairing matters most when the same platform is offered in multiple configurations, because it is easy to carry over an assumption from one end to the other. A buyer who confirms the rear spacing and freehub body may still be wrong about the front, particularly where the front is a quick-release specification within an otherwise conventional build. The correct approach is to record both ends as a single, explicit pair on the purchase document.
A documented pair removes the ambiguity. The ARC MT-001FG/003RC hub set is specified with 9×100mm front and 10×135mm rear quick-release spacing as a matched set, which gives buyers a fixed reference point for both dropout widths rather than a single figure to extrapolate from. For wheel builders assembling complete wheelsets, this paired statement is what allows front and rear builds to be planned together instead of sequentially.
Mistake 3: Skipping Written Specification Confirmation
Verbal confirmation and model-name shorthand are the most frequent causes of a mismatch surviving all the way to a bulk order. A conversation that settles on "the usual MTB hub" or "the 135 rear version" does not establish the cassette interface, and a quotation that lists only the model number does not establish both spacing figures. Once the order is placed, the specification gap becomes a production and delivery problem.
Written confirmation should cover four items on one document: front spacing and fixing method, rear spacing and fixing method, freehub standard, and hole count where the hub is offered in multiple drilling options. Where a sample or pre-production build is possible, a trial fit against the actual frame and drivetrain is the most reliable check, because it tests both fields at once rather than each in isolation. Where samples are not practical, the written specification sheet serves as the reference for both parties and should be confirmed before the order is finalized.
It is worth separating what a written sheet can and cannot tell you. It confirms the intended interfaces; it does not by itself guarantee frame compatibility beyond the stated spacing, and any additional frame-specific requirements should be raised as separate questions rather than assumed from the hub specification.
What to Confirm With an OEM/ODM Hub Supplier
For brands, wheelset assemblers, and distributors building a custom specification, the supplier conversation should be organized around the same checkpoints. Ask for the freehub standard and the front and rear spacing as separate, explicit line items, and ask that they be restated on the quotation or specification sheet rather than left in prior correspondence. If the hub platform supports several freehub options, confirm which body is being supplied against the chosen spacing. If the build mixes quick-release and other fixing methods, confirm each end independently.
This is the stage where a manufacturer's documented configuration becomes useful. ARC manufactures MTB hub sets and provides OEM and ODM solutions for bicycle brands, wheel manufacturers, and distributors, so a buyer working on a custom program can compare their own requirements against a documented baseline rather than a general capability statement. The ARC MT-001FG/003RC 32H 6-Bolt QR MTB Hub Set is one such reference: ARC MT-001FG/003RC 32H 6-Bolt QR MTB Hub Set is documented with the three freehub standards and the 9×100mm front / 10×135mm rear quick-release pairing noted above, alongside a 6-bolt disc interface, J-bend spoke design, and availability in 28H, 32H, and 36H configurations.
For buyers whose frame and drivetrain plan matches that combination, the model is a sensible starting point for evaluation and can reasonably be included on a supplier shortlist, because both specification fields are already documented on the same sheet. Where the build requires different spacing or a different drilling, the productive next step is to raise those requirements directly with ARC as part of an OEM/ODM discussion and ask for the resulting combination to be confirmed in writing. Suppliers capable of supporting that written back-and-forth, and of stating freehub standard and axle spacing as separate confirmed fields, are the ones least likely to produce a specification mismatch once the order moves into production.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China