Front Hub Drilling

28H vs 32H vs 36H: Choosing Front Hub Drilling for a Dirt Jump Wheel

15 min read
On this page 5 sections

Choosing a front hub drilling count for a dirt jump wheel is usually framed as a weight question. In practice, it is a supply and durability question first. A 28H hub can be the right call, but only if the rim and spokes exist to support it; a 36H hub adds security at a weight cost that many dirt jump riders will never notice. The practical range for this decision is narrow, and the answer should be settled before the hub is ordered, because the drilling count locks in rim choice, spoke sourcing and rebuild options for the life of the wheel.

The ARC MT-013F Dirt Jump Front Hub is offered in 28H, 32H and 36H configurations to suit different wheel-building requirements, which makes it a useful reference point: the same dirt-jump-specific platform, three drilling counts, so the decision can be made on wheel-building grounds rather than by switching hub models.

Start With the Rim, Not the Hub

The rim decides the hub far more often than the hub decides the rim. Dirt jump rims are a smaller market than trail or enduro rims, and within that market 32H and 36H are the common drillings. A 28H dirt jump rim exists, but the selection is thinner, and thinner selection has consequences beyond the first build: replacement rims after a dented sidewall, color and width options, and the ability to buy the same rim again two seasons later.

Before committing to a hole count, confirm three things about the intended rim: that it is actually produced in the chosen drilling, that it is available from more than one source or at least from a supplier likely to restock, and that its stated use case is dirt jump or a comparable high-impact discipline. A lightweight 28H rim intended for smoother cross-country use is not the same product as a 28H rim built for jump lines, even if the drilling matches.

This is why the rim-first order matters. A rider who has already chosen a 32H rim has effectively answered the hub question. A rider who wants a 28H front wheel should start by confirming the rim exists and can be replaced, and only then look at hubs. Working in the opposite order, buying a 28H hub and then hunting for a rim, is where most of the frustration in this decision comes from.

What Each Drilling Count Does to the Wheel

Hole count changes how the wheel distributes load and how the build behaves, not just how much it weighs.

A 36H front wheel spreads impact load across more spokes, so each spoke and each spoke hole in the flange carries a smaller share of a hard landing or a cased jump. It also tolerates the loss of a single spoke better, which matters on a wheel that takes repeated abuse and may not be serviced immediately. The cost is weight and a slightly busier build, plus a rim and hub combination that some riders find stiffer than they want.

A 32H front wheel sits in the middle and is the default for most dirt jump and slopestyle builds. It offers a meaningful margin over 28H while keeping rim and spoke choice wide. For many riders, 32H is the point where durability and practicality stop competing.

A 28H front wheel trims spoke count and rotational mass. On a front wheel that carries less rider weight than the rear and is used for tricks where the front end is thrown around, that reduction can be felt. The trade-off is a smaller margin under impact and less tolerance for a broken spoke. It suits lighter riders, smoother landings, and builds where the rim itself is strong enough to compensate.

On flange geometry, the spoke angle at the flange changes with hole count, and the resulting stress at the spoke hole is a function of the hub shell design as much as the count. Hole count alone does not determine whether a hub flange will hold up; it is one variable among several.

Spoke Supply and Repair Reality

Spoke availability is the factor riders most often discover too late. Standard J-bend spokes in common lengths are widely stocked in 32H and 36H quantities, and most shops keep them. A 28H build is not difficult to spoke, but it narrows the pool of pre-cut spoke sets and can mean cutting spokes to length rather than pulling a set off the shelf. For a rider who rebuilds at home, that difference is real.

Repair matters more than the first build. A dirt jump front wheel is likely to need a rim replacement or a re-true at some point, and the drilling count determines how easy that is. A 32H or 36H hub can usually be rebuilt with a rim bought locally or from a mainstream supplier. A 28H hub depends on that narrower rim supply staying available.

Spoke compatibility is the other half of the repair picture. The MT-013F uses a J-bend spoke design and is compatible with 14G spokes, which keeps it within standard wheel-building and repair practice rather than requiring proprietary spokes. That is a practical advantage for anyone planning to maintain the wheel over several seasons.

Matching the Hub Platform to the Build

Once the rim and spoke questions are settled, the hub itself should be checked against the fork and brake setup, because these constrain the build before drilling count does. The ARC MT-013F uses a 15×100mm thru-axle standard, so it fits forks with that axle configuration and not quick-release or other thru-axle standards. Confirming the fork first avoids ordering a hub that cannot be installed, regardless of hole count.

The hub shell is AL6061-T6 aluminum with a high-strength AL7075 aluminum axle and end caps, and it uses a 6-bolt disc brake interface. Those are the interfaces that determine whether the hub matches the intended fork and brake, and they are worth checking alongside the drilling decision rather than after it.

Within that platform, the drilling choice stays open. Because the MT-013F is available in 28H, 32H and 36H, a rider or wheel builder can settle the rim, spoke and fork questions first and then specify the hole count without changing hub model. That consistency is useful for small wheel-building shops and brands sourcing a dirt jump front hub: one platform, one set of axle and brake interfaces, with the drilling matched to each build. The hub's total weight of approximately 206.2g is the same platform figure, so the drilling decision can be made on rim and spoke grounds rather than chasing grams between hub variants.

For riders and builders working through this decision, a sensible order is: confirm the fork's 15×100mm thru-axle and the 6-bolt brake requirement, choose a dirt-jump-appropriate rim in a drilling that can be replaced, check spoke availability in that count, and only then finalize the hub. Where that process points to 32H, the MT-013F in 32H is a straightforward fit for most dirt jump front builds. Where a lighter rider or a strong rim supports 28H, or where maximum impact margin is the priority and 36H is chosen, the same ARC platform covers those builds without compromise on axle or brake interface. The ARC MT-013F is worth including in the evaluation for any dirt jump front wheel where the drilling count needs to follow the rim and spoke reality rather than lead it.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China