OEM Fixed-Gear Builds

AL6061-T6 Hub Shell Track Hubs with AL7075 Axle and End Caps: What to Specify for OEM Fixed-Gear Builds

18 min read
On this page 5 sections

For OEM fixed-gear and track programs, the hub is rarely the part that gets the most attention during design reviews—yet it is one of the hardest components to change late in a build. The axle, end caps, threading, and locking structure all interact with the frame, the cog, and the rider's setup, so a material or specification decision made on a spec sheet can turn into a tooling or assembly problem months later. This is why the ARC GT-002FR is worth examining at the material level: its specification pairs a fully CNC-machined AL6061-T6 hub shell with a high-strength AL7075 aluminum axle, freehub components, and end caps, and the combination is a useful reference point for buyers drafting an OEM track hub brief.

Why the Shell and the Axle Use Different Aluminum Alloys

A common assumption among buyers new to hub sourcing is that one "good aluminum" throughout the hub is sufficient. In practice, the shell and the axle perform different jobs, and the alloy choice follows the function rather than a single cost target. On the GT-002FR, ARC specifies a fully CNC-machined AL6061-T6 hub shell. AL6061 in the T6 condition is a precipitation-hardened alloy with good machinability and dimensional stability, which matters when a shell has to hold bearing bores, flange spacing, and spoke hole positions within tight tolerances across a production run. Because the shell is machined rather than cast, the wall sections and flange geometry can be defined directly in the program, and changes between production batches are easier to control.

The axle tells a different story. It carries the rider's load, the clamping force from the track nuts or quick-release, and the bending moment transferred from the frame—so the design priority shifts toward strength and stiffness. AL7075 is a zinc-bearing aluminum alloy with notably higher strength than 6061 in comparable tempers, which is why ARC uses it for the axle, the freehub components, and the end caps on this hub rather than carrying the shell alloy through the whole assembly. The end caps deserve particular attention: they are the interface between the hub and the frame dropouts, they are handled during every wheel change, and they take the compressive load from the axle nuts. Specifying them in AL7075 supports that contact duty.

For a buyer, the practical takeaway is not simply "7075 is better." It is that the material split reflects a division of labor—dimensional consistency in the shell, load-bearing strength in the axle and end-cap assembly—and that OEM discussions should treat these as separate specification lines rather than a single "aluminum hub" line item.

Internal Lock Structure and Double-Sided Threading in a Fixed-Gear Build

Fixed-gear drivetrains load the hub differently from geared systems. The sprocket is threaded directly onto the hub, and during hard braking or back-pedaling the torque reverses direction. That reversal is the reason fixed-gear hubs use a lockring: the cog is tightened by pedaling force in one direction, and the lockring—threaded in the opposite hand—prevents the cog from unthreading when the rider resists the pedals. A hub that does not address this properly creates a well-known failure mode in which the cog loosens under braking.

The GT-002FR addresses this with an integrated internal locking structure and double-sided fixed-gear threading. The internal lock structure means the locking feature is built into the hub body rather than relying on an external clamp or adapter, which keeps the assembly compact and gives the lockring a defined seat. Double-sided threading provides setup flexibility: the hub can be configured for a fixed-gear drive on either side, which matters for brands building flip-flop style wheelsets or for builders who want to offer a single hub platform across different frame specifications.

For the product manager, the points to carry into the build sheet are the thread standard and hand of the drive-side and non-drive-side threads, the lockring interface dimensions, and the chainline that results from the chosen configuration. These are the variables that determine whether the hub drops into an existing frame design or requires a change to the rear spacing or dropout specification.

What the 16T Cog and Lockring Change for Your Build Sheet

The GT-002FR is supplied with a 16T fixed-gear cog and lockring, which changes the sourcing conversation in a subtle but useful way. A bare hub leaves the brand responsible for sourcing a cog with a compatible thread and a lockring with the correct interface, and mismatches between these three parts are a recurring source of assembly and warranty issues. Supplying the cog and lockring with the hub means the thread engagement and locking interface are defined as a set.

That said, the supplied 16T cog is a starting specification, not a universal answer. Gear ratio is a function of the intended use—track racing, street fixed-gear, or a mixed-use build—and the chainring size the brand pairs with the hub. A 16T cog is a common baseline, but buyers should confirm whether their program requires a different tooth count, and whether the cog and lockring are to be included in the OEM shipment or treated as an accessory line. It is also worth clarifying in the purchase specification whether the lockring is intended for the drive side only or for both threaded sides in a flip-flop configuration, since that affects what the brand needs to stock and document for its dealers.

Specification Points to Confirm Before an OEM/ODM Order

With the material and drivetrain basics established, the OEM conversation can move to the variables that actually determine whether the hub fits the program. ARC provides OEM and ODM solutions for global bicycle brands, wheel manufacturers, and distributors, so the following points are the ones to lock down early rather than after a sample is approved.

  • Axle configuration and end caps: confirm the axle diameter and length, the end-cap profile for the intended dropout type, and whether the end caps are fixed or interchangeable. Because the GT-002FR uses AL7075 for the axle and end caps, any change to these parts should be treated as a new specification, not a cosmetic variation.
  • Threading and locking interface: specify the thread standard and hand on each side, the lockring interface, and whether the internal lock structure is common across all configurations in the order.
  • Cog and lockring scope: state the tooth count, whether the 16T cog is the standard supply or a placeholder, and whether the cog and lockring ship with every hub or as a separate line item.
  • Shell interface details: confirm flange geometry, spoke hole count and drilling, bearing specification, and the finish or anodizing requirement, since these are the shell features most likely to be customized for a brand.
  • Sampling and validation: agree on what the sample is meant to prove—fit in the frame, thread engagement with the supplied cog and lockring, and assembly repeatability—before committing to production quantities.
  • Order and documentation terms: clarify minimum order quantities, lead times, packaging, and the technical documentation the brand will need for its own dealer network.

None of these points should be assumed from a catalog page. Where a specification is not confirmed in the supplier's documentation, it belongs on the inquiry as an open question.

For brands and wheelset builders specifying a track or fixed-gear hub, the GT-002FR is a reasonable candidate to put on the evaluation list precisely because its material baseline is defined—AL6061-T6 for the machined shell, AL7075 for the axle, freehub components, and end caps—and because the internal lock structure, double-sided threading, and supplied 16T cog and lockring are specified as a system rather than as separate parts. Buyers whose requirements center on a defined fixed-gear locking interface and a clear material split between shell and load-bearing components will find the specification easier to assess against their frame and drivetrain requirements. The next step is to take the checklist above into an OEM/ODM inquiry with ARC, confirming the axle and end-cap configuration, thread details, and cog and lockring scope before samples are requested.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China