Mountain bike hub specification is rarely decided by a single headline material. For OEM buyers and wheel builders, the practical question is whether a hub set's material pairing, drilling options, freehub interface and bearing choice line up with the wheel program they intend to produce—and what still needs to be confirmed before committing to samples or volume. The ARC MT-001FS/RS addresses that question with a defined combination: an AL6061-T6 aluminum hub shell with AL7075 aluminum axle, freehub body and end caps, plus selectable 28H/32H/36H drilling and a choice of Shimano HG, Micro Spline or SRAM XD freehub standards.
What the AL6061-T6 Shell and AL7075 Freehub Body Do in an MTB Hub Set
The two aluminum grades are not interchangeable, and understanding their separate roles explains why the pairing appears in the same hub set. The hub shell is the structural body that carries the spoke flanges, houses the bearings and anchors the brake interface. AL6061-T6 is a widely used shell material because the T6 temper delivers a practical balance of strength, machinability and corrosion behavior for CNC-machined bicycle components. In the MT-001FS/RS, the shell is the part that defines spoke drilling, flange geometry and the 6-bolt disc mount.
The freehub body, by contrast, is the component the cassette splines onto and the part that receives drive torque through the pawl mechanism. Because it is smaller in section and carries concentrated loads at the splines, the material choice tends toward higher strength. AL7075 is a zinc-bearing aluminum alloy known for high strength-to-weight characteristics, and ARC uses it not only for the freehub body but also for the axle and end caps. That means the load-bearing drivetrain and axle elements are grouped under one higher-strength material, while the shell remains a machined AL6061-T6 body optimized for geometry and bearing seats.
For a buyer, this division matters when evaluating wear and service life expectations. The freehub body is the part most exposed to spline wear and cassette torque, so its material is a legitimate specification talking point. The shell's material and machining affect bearing fit, spoke hole integrity and brake mount flatness. What the pairing does not tell you on its own is a fatigue life figure or a rider weight limit—those depend on wall thickness, bearing selection, spoke tension and build quality, and should be confirmed with the supplier rather than inferred from the alloy names. The engagement system itself is described as a 3-pawl, single-tooth design, a simple structure that suits everyday trail use and straightforward maintenance. Downstream, that simplicity helps workshops service the hub without specialized tooling, which is a real consideration for distributors supporting a broad dealer network.
Choosing 28H, 32H or 36H for Your Wheel Program
Hole count is one of the first variables to lock down because it constrains spoke procurement, rim matching and the wheel's intended duty. The MT-001FS/RS is offered in 28H, 32H and 36H configurations, giving a single model family coverage across several build tiers.
The practical logic runs along a spectrum. Fewer spoke holes generally mean a lighter, more aerodynamic-looking wheel with fewer spokes to tension and replace, but each remaining spoke carries a larger share of the load. Higher hole counts distribute load across more spokes and are conventionally associated with greater robustness and easier truing tolerance, at the cost of some weight and spoke count. A 28H build suits lighter riders, weight-conscious trail wheels and programs where rim stiffness is designed to compensate. A 32H build is the middle ground most everyday trail and general-purpose MTB wheelsets settle on, balancing durability and weight. A 36H build is the conservative choice for heavier riders, loaded use, or programs that prioritize repairability and spoke redundancy.
The right approach for an OEM buyer is to start from the target bike's intended use and rider profile, then confirm rim drilling matches. If a wheel brand plans several price tiers on one hub platform, offering all three drillings under one model simplifies spoke stocking and dealer support. Hole count should always be validated together with rim specification and spoke type, since a drilling that suits one rim may not suit another.
Freehub and Bearing Options That Shape the Specification
The freehub standard is the specification most likely to cause a compatibility failure if left ambiguous, because it follows the drivetrain rather than the wheel. The MT-001FS/RS supports Shimano HG, Micro Spline and SRAM XD freehub standards. Each corresponds to a different cassette interface family, so the buyer should select the standard that matches the groupset families the finished bike or wheelset will be sold with, and specify it explicitly on the purchase order rather than assuming a default.
Bearing choice forms a second specification axis. ARC lists S&S steel, ENDURO and CeramicSpeed bearing options, allowing a tiered build where a value-focused wheelset and a premium wheelset share the same hub shell and freehub architecture but differ in bearing package. For distributors, that tiering can reduce SKU complexity in the hub body while still offering a meaningful upgrade path. The engineering point to keep in mind is that bearing selection affects rolling characteristics and service intervals, but it should be evaluated as part of a system—seals, grease fill, preload and riding conditions all influence bearing life, so a premium bearing name alone is not a performance guarantee.
Engagement is the third variable. The 3-pawl, single-tooth system is a defined mechanism, and buyers should confirm the engagement expectations for their target riding style against the supplier's specification rather than assume a particular engagement angle. Asking for the engagement details in writing is a reasonable pre-sample step.
Interface Details: 6-Bolt, QR and J-Bend Spokes
A hub set is only a component within a larger build, and interface choices determine whether it drops into an existing frame, rotor and spoke plan. The MT-001FS/RS uses a 6-bolt disc brake interface and a J-bend spoke design, and it is specified as a QR (quick-release) hub set.
The 6-bolt mount is one of the two common rotor attachment standards, so the buyer should confirm that the rotor spec for the target build matches six-bolt rather than center lock. The J-bend spoke design accepts conventional J-bend spokes, which are widely stocked and familiar to wheel builders, and it is a practical choice for programs that want broad spoke availability. Straight-pull spokes are a different design and would require a different hub flange; this hub set is not a straight-pull design, so spoke sourcing should be planned accordingly.
QR specification is equally consequential. Frames and forks designed around thru-axles will not accept a QR hub set without the appropriate frame interface, so the buyer should verify the dropout standard of the intended frame before finalizing. End caps are part of the AL7075 group in this hub set, and the buyer should confirm the exact axle and end-cap configuration for the frame standard in the program.
What to Confirm Before Sampling or Bulk Ordering
The specification checklist above converts into a set of questions worth resolving before a sample leaves the factory. Working through them in writing reduces the risk of a costly mismatch between the sample and the volume order.
- Drilling: Confirm 28H, 32H or 36H against the rim and spoke plan, and whether mixed drillings can be ordered within one program.
- Freehub standard: Specify Shimano HG, Micro Spline or SRAM XD per build, and confirm cassette compatibility for each groupset family.
- Bearing option: Decide S&S steel, ENDURO or CeramicSpeed per price tier, and ask how bearing choice is identified on the order and packaging.
- Axle and frame interface: Confirm QR configuration and end-cap specification against the target frame's dropout standard.
- Brake and spoke interface: Verify 6-bolt rotor compatibility and J-bend spoke availability, and confirm spoke length against the actual flange dimensions.
- Engagement and service: Request the 3-pawl engagement specification and ask about service procedures and spare pawl or freehub body availability.
- Sample validation: Agree what the sample will be checked against—spoke tension, bearing fit, rotor alignment and freehub function—before volume release.
- OEM/ODM terms: Clarify branding, packaging, order quantities, lead times and inspection criteria as part of the commercial agreement, since these are program-specific rather than fixed product attributes.
ARC, based in Taicang, Jiangsu, manufactures bicycle hubs and provides OEM and ODM solutions for bicycle brands, wheel manufacturers and distributors. The MT-001FS/RS is a concrete example of that capability applied to a defined MTB specification: an AL6061-T6 shell with AL7075 axle, freehub body and end caps, three drilling options, three freehub standards and three bearing tiers within one model. For buyers building everyday trail and entry-level MTB wheelsets, that combination is a practical platform to evaluate—and the sensible next step is to take the checklist above to ARC, confirm the exact configuration against the target wheel program, and validate it with a sample before committing to volume.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China