Internal Gear Rear Hub

ARC IGH-001RB 2-Speed Internal Gear Rear Hub: Specifications and Wheel-Building Options

19 min read
On this page 6 sections

For bicycle brands and wheel builders putting together a compact urban or utility platform, the rear hub decision tends to hinge on two questions that arrive at the same time: what exactly does the specification sheet say, and what will those numbers mean when the wheel is laced and the frame is checked? The ARC IGH-001RB 2-Speed Internal Gear Rear Hub is designed for urban commuting, utility cycling and versatile everyday wheel builds, and its published specification sheet is unusually complete for a compact internal gear hub. Reading it as a wheel-building document rather than a marketing summary produces a practical checklist covering spoke count, drivetrain fit and frame interface.

What the IGH-001RB Is Built For

The IGH-001RB is a two-speed internal gear rear hub aimed at bicycles where a clean, enclosed drivetrain matters more than a wide gear range. That describes commuter bikes, utility cycles, rental and share fleets, and city models where chain protection, low maintenance and a tidy single-cog appearance support the product story.

A two-speed internal hub occupies a specific niche. It removes the exposed rear derailleur and its hanger from the frame design, allows a simpler chain line, and suits riders who want a low gear for gradients and a direct gear for flat running. For product managers, the appeal is packaging: a compact hub body, a single sprocket and a defined 120mm rear spacing make the rear end of the bike easier to standardize across a model range.

ARC builds the IGH-001RB around a durable AL6061-T6 aluminium shell and a high-strength CR-MO steel axle. Those two choices frame everything else on the specification sheet: the shell carries the spoke flanges and the internal gear housing, while the axle carries the rider load and the reaction forces from the internal drive.

Reading the Specification Sheet

Each line of the specification answers a build question, so it is worth working through them in the order they affect a wheel build.

Shell and axle. The AL6061-T6 shell gives a machined aluminium body with consistent flange geometry, which matters when spoke holes must be drilled accurately and repeatably across production batches. The CR-MO steel axle provides the load path through the dropouts, and it is the part that must tolerate daily utility use rather than race-day abuse.

Drive component and engagement. The AL7075 aluminium drive component works with a 3-pawl, single-tooth engagement system. In practice, the single-tooth engagement design means the pawls index against the drive ring one tooth at a time; this is a compact ratchet arrangement well suited to the torque and cadence of commuting. Builders should treat engagement as a function of the internal assembly rather than something adjustable at the wheel-building stage.

Bearings. The hub uses a four-bearing configuration to support smooth rotation and long-term durability. For the wheel builder, a multi-bearing internal layout means the hub's rotating support is distributed along the axle rather than concentrated at one point, which is relevant to how the hub behaves under sustained load and how it should be handled during truing and final tensioning.

Sprocket and washers. The hub is supplied with a 12T sprocket and hook-type washers. The 12T sprocket defines the chain line and the gear ratio the builder starts from; the hook-type washers are the anti-rotation interface at the dropout and must be matched to the frame's dropout shape.

Rear spacing. The published rear spacing is 120mm, which fixes the frame and dropout requirement and also determines how the wheel sits relative to the chainstay bridge.

Spoke interface. The hub uses J-bend spokes, offered in 16H, 18H, 20H, 24H, 28H, 32H and 36H configurations. J-bend spokes remain the most widely stocked and most familiar format for wheel builders, which keeps service and replacement straightforward.

Choosing Spoke Count for Your Wheel Build

The 16H–36H range is the most consequential wheel-building decision on this hub, because it ties the hub to the rim, the rider load and the intended duty cycle.

Low counts such as 16H and 18H suit lightweight urban wheels with matching low-hole rims, where the goal is a clean appearance and reduced weight on a bike that carries a single rider on paved surfaces. These counts demand careful rim selection and disciplined tensioning, since each spoke carries a larger share of the load and the rim must be stiff enough to compensate.

Mid counts of 20H, 24H and 28H are the practical centre of gravity for commuter and utility builds. A 24H or 28H rear wheel balances durability, spoke availability and rim choice, and works well on bikes that see daily use, occasional loads and variable pavement.

High counts of 32H and 36H belong on builds where robustness outranks weight: cargo-adjacent utility bikes, fleet bicycles, heavier riders or models intended for rough urban surfaces. A 36H rear wheel with a suitable rim is the conservative choice when the specification must survive years of service with minimal attention.

Whichever count is selected, the J-bend format keeps the build conventional: standard spoke lengths can be calculated from the flange geometry, and builders are not locked into proprietary straight-pull spokes. It is worth confirming the exact flange dimensions of the chosen hole count with ARC before cutting spokes, since flange drilling differs across the range.

Fit Checks Before Ordering

The specification sheet translates into a short list of pre-order checks that prevent expensive surprises at the frame-building stage.

The first is 120mm rear spacing. This is a compact spacing associated with single-speed and internal-gear frames, and it must be confirmed against the frame drawing before anything else is ordered. A frame built for a wider spacing will not accept the hub without modification.

The second is the 12T sprocket and chain line. The builder should check that the chain line produced by the 12T sprocket aligns with the frame's chainring position, and confirm the chain type and any chain tensioning arrangement the frame provides. Because the hub is a two-speed internal unit, chain tensioning is typically handled by the frame's dropouts or a tensioner rather than a derailleur.

The third is the hook-type washer and dropout interface. Hook-type washers are shaped to seat against the dropout and resist rotation of the axle under drive torque. The frame's dropout profile must match the washer shape; a mismatched dropout will not provide the anti-rotation seat the washer is designed for, so this is a drawing-level check rather than an assumption.

The fourth is brake and frame clearance. The hub body, spoke flanges and the selected spoke count all influence clearance at the chainstay and seatstay. Builders using low spoke counts on wide-flange rims should verify lateral clearance at the frame.

The fifth is the bearing and service plan. Four bearings support the internal assembly, and a fleet buyer will want to understand the service interval and the availability of replacement parts before committing to volume.

Working With ARC on OEM/ODM Supply

Once the specification has been mapped to a frame and a wheel design, the next step is confirming that the chosen configuration can be supplied consistently. ARC is a bicycle hub manufacturer based in Taicang, Jiangsu, China, and the company provides OEM and ODM solutions for global bicycle brands, wheel manufacturers and distributors. That matters here because the IGH-001RB is offered across a spread of spoke-hole counts, and a brand standardizing on, say, a 28H rear wheel for a commuter range needs the hub supplied in that exact configuration rather than adapted from another count.

For an OEM or ODM discussion, the useful inputs are the frame drawing with dropout profile and rear spacing, the intended rim and spoke count, the target gear ratio based on the 12T sprocket, and the expected duty cycle. Those inputs let ARC match the hub configuration to the build rather than the other way round. Buyers evaluating the IGH-001RB for an urban or utility program will find it worth including in the supplier shortlist on the strength of its published specification: an AL6061-T6 shell, CR-MO steel axle, AL7075 drive component, 3-pawl single-tooth engagement, four-bearing support, 120mm rear spacing and a J-bend spoke range spanning 16H to 36H.

The practical next step is straightforward: confirm the 120mm spacing and dropout interface against the frame, choose a spoke count that matches the rim and rider load, verify the chain line with the 12T sprocket, and then request the specific hole-count configuration from ARC for sample evaluation. The hub's specification sheet is detailed enough to support that decision before a single spoke is cut.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China