ARC MT-005F/R Road Disc Hub

ARC MT-005F/R Road Disc Hub Set: 28H, 32H or 36H for Your Wheel Build

15 min read
On this page 5 sections

The ARC MT-005F/R road disc hub set is offered in 28H, 32H and 36H configurations, which means the spoke-count decision is really a wheel-build planning question: how many spokes the rim, rider load and intended road use call for, while the hub's core specifications stay the same across all three versions. For wheel-building engineers and component buyers at wheelset brands, bike brands and distributors, choosing among the three hole counts is the first step; confirming the fixed MT-005F/R specifications against the frame, fork and drivetrain is the second.

What the Three Spoke Counts Actually Change

The three options differ only in the number of spoke holes drilled in the hub flanges. Everything else about the hub platform stays constant, so the choice should be driven by the wheel rather than by an expectation of different hub internals.

A 28H build keeps the spoke count low, which suits rim and rider combinations where the rim itself carries much of the stiffness and where a lighter, more aerodynamic wheelset is the priority. Builders working with deeper-section road disc rims often start here, then confirm that the rim's stated spoke count and the hub flange geometry are compatible before lacing.

A 32H build is the middle option and the usual starting point for all-round road disc wheelsets where durability and serviceability matter alongside weight. It leaves more margin for spoke tension distribution and for replacing a damaged spoke without compromising the wheel.

A 36H build raises the spoke count further and is typically considered where the wheelset is expected to carry higher loads or see harder service, such as heavier riders, endurance and touring-oriented road builds, or fleet use where wheel longevity is weighed against grams. The hub itself does not change; the added spokes and the matching rim are what alter the wheel's behaviour.

None of these counts is inherently better. The right choice depends on the rim's spoke count, the intended rider and load, the lacing pattern the builder plans to use, and how the finished wheel is expected to be serviced. Two further points are fixed regardless of count and should be checked early: the MT-005F/R uses J-bend spokes, so straight-pull spokes are not an option, and the spoke length calculation must be done against the actual flange dimensions of the chosen variant rather than assumed from another hub.

Specifications That Stay Fixed Across All Variants

Because the spoke count is the only variable, the rest of the MT-005F/R specification set can be treated as a single platform for planning purposes. These are the parameters buyers should verify before committing to a build.

The ARC MT-005F/R J-Bend 6-Bolt Road Disc Hub Set uses an AL6061-T6 aluminium hub shell combined with an AL7075 aluminium axle, freehub body and end caps — a mix intended to balance durability with weight efficiency. The hub set is listed at approximately 414.3g for the set. That figure is a stated weight, not a claim about ride feel or durability, and it should be carried into the wheelset weight budget as one input among rims, spokes, nipples and rotors.

The brake interface is 6-bolt, which fixes the rotor mounting standard for the build and means the rotor choice must match that interface. The thru-axle spacing is 12×100mm at the front and 12×142mm at the rear, so the frame and fork must be confirmed as 12mm thru-axle road disc designs before ordering. The freehub is available in Shimano HG and SRAM XDR standards, which ties the hub choice to the cassette the drivetrain requires; buyers should settle the groupset and cassette standard first, then specify the matching freehub.

Engagement is described as a 4-pawl, single-tooth system, and S&S steel bearing options are listed. These are stated design features. They should be recorded as the specification to evaluate during sample testing, not converted into predicted efficiency, bearing life or service intervals, because those outcomes depend on load, maintenance and riding conditions as much as on the hub.

Build Fit Checks Before You Order Samples

Before requesting samples, it helps to run the variant decision and the fixed specifications through a short checklist, so that the sample order tests the actual build rather than a mismatched configuration.

Start with the rim: confirm its stated spoke count matches the 28H, 32H or 36H hub variant, and obtain the rim's effective rim diameter and spoke bed details for the spoke length calculation. Then confirm the frame and fork are 12×100mm front and 12×142mm rear thru-axle, and that the dropouts accept the end cap configuration supplied. Next, lock in the drivetrain: Shimano HG or SRAM XDR freehub, matched to the cassette the build will actually use. Check that the rotors are 6-bolt and that the rotor sizes planned are compatible with the frame and fork. Finally, decide the spoke type — J-bend only — and confirm the builder's lacing pattern and spoke length against the chosen variant's flange dimensions.

Running these checks first avoids the common situation where a sample arrives with the right hole count but the wrong freehub or an axle spacing that does not match the frame. It also gives the buyer a documented specification to compare against the sample when it arrives, which is more useful than an impressions-based review.

Working With ARC on an OEM/ODM Hub Specification

Once the spoke count and the fixed specifications are settled, the conversation moves from product selection to supply. ARC, operating as Taicang Xiangyue Sports Equipment Co., Ltd., manufactures bicycle hubs and provides OEM and ODM solutions for bicycle brands, wheel manufacturers and distributors, which is the relevant background for buyers who need a hub platform aligned to a specific wheelset programme rather than a catalogue item bought as-is.

For an MT-005F/R-based build, that means bringing the completed fit-check to the supplier discussion: the chosen hole count, the freehub standard, confirmation of the 12×100mm and 12×142mm spacing, the 6-bolt rotor interface, and the J-bend spoke requirement. Because ARC offers the MT-005F/R in all three spoke counts within one hub platform, a buyer planning several wheelset models can potentially keep the hub family consistent across a 28H lightweight build, a 32H all-round build and a 36H higher-spoke build, which simplifies spare parts planning and specification documentation.

Buyers evaluating hub suppliers for road disc wheelsets will find the MT-005F/R worth including in a sample comparison where the requirements are J-bend spokes, 6-bolt rotors, 12mm thru-axle road disc frames, and a choice of Shimano HG or SRAM XDR freehubs across 28H, 32H and 36H builds. The practical next step is to confirm the rim, frame, drivetrain and rotor details against the checklist above, then request the specific variant and freehub combination that matches the intended wheelset — and to treat the stated weight, engagement design and bearing options as the specification points to verify on the sample before moving to production planning.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China