OEM Wheel Builds

ARC MT-009FE/RE 80T 6-Bolt MTB Hub Set: Specs and Configuration Options for OEM Wheel Builds

15 min read
On this page 6 sections

For OEM wheel builders, the real challenge with a hub set is rarely the headline spec. It is whether one hub family can cover the frame standards, drivetrain setups, and spoke counts across an entire model range without forcing separate stock lines for every variation. The ARC MT-009FE/RE 80T 6-Bolt MTB Hub Set is built around that problem: a 4-in-1 axle design, three freehub body options, and three spoke counts, all within a single model. What follows is a configuration-by-configuration breakdown so buyers can match each option to their builds before committing to a specification.

Axle and Frame Compatibility

The MT-009FE/RE uses a 4-in-1 axle design that covers both quick-release and thru-axle frames: 9×100mm and 10×135mm QR, plus 15×100mm and 12×142mm thru-axle. For wheel builders, this is the most consequential configuration decision, because it determines how many hub variants an OEM program needs to stock and document.

A single hub model spanning QR and thru-axle standards means a builder producing wheelsets for multiple frame platforms can consolidate around one hub family rather than maintaining parallel part numbers for each axle type. The practical benefit is less inventory fragmentation across size runs, and simpler build documentation when the same hub appears in several complete-bike specifications. The trade-off is that end caps and axle hardware must be specified correctly per build, so confirming the exact axle combination at order stage—rather than assuming a default—is the step that keeps a mixed-platform program running smoothly. ARC lists the specific QR and thru-axle standards as separate supported configurations, so each should be called out explicitly in the purchase specification.

Drivetrain and Freehub Options

Freehub body choice is the second variable that shapes a hub set's fit across a model range. The MT-009FE/RE is offered in Shimano HG, Micro Spline, and SRAM XD, which together span the common MTB drivetrain families that OEMs and aftermarket wheel brands are likely to build around.

For OEM purchasing teams, the value is straightforward: one hub platform can be ordered against different drivetrain specifications without introducing a new hub design. A brand selling across markets where Shimano and SRAM drivetrains both appear can keep a single hub model in its bill of materials and vary only the freehub body. Builders should confirm the freehub option per order line together with the axle configuration, since these two choices are usually made at the same point in the purchasing cycle. The freehub is also part of the hub's high-strength AL7075 construction alongside the axles and end caps, which keeps the rotating assembly consistent across the three options.

Spoke Counts and Build Integration

Spoke interface is where a hub set meets the wheel builder's own lacing plan. The MT-009FE/RE comes in 28H, 32H, and 36H J-bend configurations, and the 6-bolt disc brake interface defines the rotor mounting standard for every build.

These are the choices a builder maps directly onto rim selection and intended use. As a general lacing reference rather than a claim about this specific hub's limits, 28H suits lighter builds where weight is a priority, 32H is the common all-round count, and 36H serves heavier-duty or higher-load builds. Because the hub uses J-bend spokes, it takes standard J-bend tooling and spoke stock, which simplifies sourcing for builders already tooled for that format. The 6-bolt interface is equally a planning point: rotors and hardware must match the 6-bolt standard, so builders should confirm this against their rotor specification before finalizing a bill of materials. Spoke count, J-bend format, and brake interface can all be fixed at the ordering stage, which keeps the hub decision locked alongside rim and spoke selection rather than surfacing later in assembly.

Engagement, Materials, and Weight

The "80T" in the model name refers to the DT-80T ratchet system: an 80-tooth engagement structure that provides frequent pickup and a broad contact interface for torque distribution. For a buyer, this is the performance core of the hub set and the reason it sits in performance-focused MTB builds rather than economy tiers.

Materials are split by function. The shell is AL6061-T6 aluminum, while the axles, freehub body, and end caps use high-strength AL7075. That division puts the lightweight alloy where it reduces shell mass and the higher-strength alloy in the load-bearing and wear-critical parts. The complete hub set weighs approximately 461.8g. Buyers should read that figure as a complete-set reference, not a per-hub weight, and should evaluate it against their wheelset target rather than in isolation—overall wheel weight depends on rims, spokes, and rotors as much as on the hubs.

As with any engagement system, the ratchet's field behavior depends on riding conditions, maintenance, and the rest of the build; the 80-tooth specification describes the engagement structure, not a guaranteed outcome on every bike. For a program built around fast pickup and dependable torque transfer, the MT-009FE/RE is worth evaluating as a candidate hub, and the full specification is set out on the ARC MT-009FE/RE 80T 6-Bolt MTB Hub Set product page.

Customization for OEM and ODM Programs

The configuration list extends beyond axle, freehub, and spoke count. The MT-009FE/RE is available with S&S steel, ENDURO, or CeramicSpeed bearing configurations, and with multiple anodized color options. These are the levers that let an OEM or ODM partner align the hub with a brand's own performance positioning and finish palette rather than taking a single fixed specification.

In practice, this means a purchasing team can define a hub specification that matches its product tiers—bearing choice for performance level, anodized color for brand identity—while keeping the underlying hub platform consistent. ARC's own role in this is as a professional bicycle hub manufacturer offering OEM and ODM solutions, with the MT-009FE/RE positioned as one documented product within that range. Bearing and color selections are best confirmed as part of the initial specification discussion, since they sit alongside axle, freehub, and spoke count in the same ordering decision. Buyers assessing the hub set should also treat any final combination as something to verify against their own build requirements before volume commitment.

Taken together, the MT-009FE/RE is a configuration-driven hub set rather than a single fixed specification. Wheel builders and OEM buyers working across QR and thru-axle frames, Shimano and SRAM drivetrains, and different spoke counts can use one hub model to cover those variations, then layer bearing and color choices on top for brand differentiation. The natural next step is to fix the axle standard, freehub body, spoke count, and bearing grade against each intended build, compare the specified set weight of approximately 461.8g with the wheelset target, and take that defined specification into a sourcing conversation with ARC.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China