What This Hub Set Is Built For
For a wheel builder, the usefulness of a hub set comes down to how many build variables it resolves before the first spoke is cut. The ARC MT-009FE/RE 80T 6-Bolt MTB Hub Set is presented as a front-and-rear pair aimed at mountain bike wheel builds that need fast engagement, flexible frame fit and a choice of drivetrain interfaces. Rather than a single fixed specification, it is a configurable platform, and that distinction shapes how buyers should read the product information.
ARC is a bicycle hub manufacturer based in Taicang, China, established in 2013, and supplies hubs as well as OEM/ODM programs to bicycle brands, wheel manufacturers and distributors. The MT-009FE/RE sits within that manufacturing context: it is a catalogue model with several selectable options, which is relevant to builders planning one wheelset and to buyers planning a repeatable product line. This article works through the stated configurations one by one so a builder can check fit against frames, drivetrains and spoke plans before ordering.
80-Tooth Ratchet Engagement in Plain Terms
The headline feature is the DT-80T ratchet system. In a ratchet-style freehub, two toothed rings engage to transmit drive; the tooth count is the most visible number because it sets the spacing between engagement points. An 80-tooth ratchet has finer teeth than lower-count designs, which the product information describes as frequent pickup and a broad contact interface intended for efficient torque distribution.
For a builder, the practical question is not whether more teeth is inherently better but what the design is stated to do. ARC's description points to quick engagement and consistent performance under demanding riding conditions. Those are design intentions rather than measured outcomes, and actual feel and durability will also depend on bearing condition, lubrication, axle fit and how the wheel is used. The ratchet system is therefore best treated as a specified engagement architecture to evaluate against a build's priorities, especially where rapid pedal pickup matters on technical terrain.
One Hub, Four Axle Standards
Frame compatibility is where hub selection most often stalls, and this is the area the 4-in-1 design addresses. The set is stated to support both quick-release and thru-axle configurations: 9×100 mm and 10×135 mm QR, plus 15×100 mm and 12×142 mm thru-axle. In practice that range covers the common front and rear standards a builder is likely to encounter across trail, cross-country and older frames.
The value of a 4-in-1 platform is that a wheel brand or OEM buyer can serve several frame standards from one hub family, reducing the number of distinct hub SKUs to stock. It does not mean one physical hub converts across every standard without the correct end caps and axle parts; those pieces must be specified per build. Before ordering, confirm which axle configuration each wheel requires and that the corresponding end caps and axle hardware are included in the quoted configuration.
Materials, Freehub and Spoke Options to Specify
The construction combines an AL6061-T6 aluminium shell with high-strength AL7075 axles, freehub body and end caps. That material split is the basis for the stated durable and lightweight construction, and it is the kind of detail a builder should record on the specification sheet, since shell and internal materials affect both weight and the way the hub is serviced.
Drivetrain compatibility is covered by three freehub options: Shimano HG, Micro Spline and SRAM XD. A builder should match the freehub to the cassette standard of the intended groupset and confirm the choice at the point of order, as freehub bodies are not interchangeable across all three standards. Spoke drilling is offered in 28H, 32H and 36H J-bend configurations, giving a choice between lighter, lower-count builds and higher-count builds with more redundancy, and the 6-bolt interface defines the brake rotor mounting. Bearing options are listed as S&S steel, ENDURO or CeramicSpeed, plus multiple anodized colour options. Each of these is a selectable variable, so a clear written specification is more reliable than an assumed default. Builders who want the full configuration list can review the ARC MT-009FE/RE 80T 6-Bolt MTB Hub Set product page alongside their order documentation.
Weight and What to Confirm Before Ordering
The complete hub set is quoted at approximately 461.8 g. That figure is a useful starting point for a build sheet, but it should be read as the stated hub-set weight for the configuration described, not a guarantee for every combination of axle, bearing and freehub choices. Weighing the actual parts received remains the reliable check.
Several items are worth confirming in writing before committing: the exact axle configuration and included end caps for each wheel; the freehub standard matching the intended cassette; the spoke hole count and J-bend drilling; the bearing selection; and the colour finish. Items such as minimum order quantities, lead times and certification are not stated in the available product information and should be raised directly with ARC rather than assumed. For wheel builders and OEM/ODM buyers, the MT-009FE/RE is a credible candidate where a single hub family needs to span QR and thru-axle frames, multiple drivetrain standards and three spoke counts. ARC's role as a Taicang-based hub manufacturer offering OEM/ODM programs makes it a sensible partner to approach with a defined specification, so the configuration discussion starts from the build requirements rather than from a stock item.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China