Dirt Jump Front Hub

ARC MT-013F 6-Bolt Dirt Jump Front Hub: 15×100mm Thru-Axle Explained

17 min read
On this page 5 sections

Dirt jump front wheel specification usually starts with a question that is easy to postpone and expensive to get wrong: which axle standard does the frame actually accept? For the ARC MT-013F 6-bolt dirt jump front hub, that answer is fixed in the product name. It is a 15×100mm thru-axle hub, and every other choice around it—spoke count, spoke type, bearing option and rotor mounting—only makes sense once that interface is locked.

The MT-013F is a listed ARC product intended for dirt jump and demanding MTB front wheel builds. That framing matters for specifiers because a dirt jump front wheel is not a generic trail wheel. It sees repeated landing loads, frequent front-wheel placement and a build philosophy that often favors durability and predictable behavior over minimizing grams. The hub is quoted at approximately 206.2g, with an AL6061-T6 shell, an AL7075 axle and end caps, a 6-bolt disc interface, J-bend spoke compatibility for 14G spokes, 28H/32H/36H drilling, and S&S steel bearing options. Each of those is a decision point rather than a decorative specification.

Why the 15×100mm Thru-Axle Comes First

A thru-axle hub only works if the frame, fork and dropout spacing agree before anything else is ordered. The MT-013F declares a 15×100mm thru-axle standard, so the first check is whether the intended fork uses a 15mm thru-axle with a 100mm hub width. Get this wrong and no amount of spoke or bearing tuning rescues the build.

It also helps to separate two different conversations that often get blended. The axle standard describes how the hub mounts to the frame and fork; the axle material describes what the hub itself is made from. The MT-013F uses an AL7075 aluminum axle and end caps, a high-strength aluminum grade, while the shell is AL6061-T6. A specifier should read those as a stated material split in the product, not as a performance guarantee. Thru-axle stiffness at the wheel level also depends on the fork, the axle itself, the hub flanges and the spoke tension, so the hub's axle standard is a compatibility fact first and a ride-feel claim second.

For dirt jump builds specifically, the practical value of confirming the thru-axle early is that it determines the fork shortlist, the hub spacing and the wheel dishing target in one step. That is why a front hub like the MT-013F is best evaluated as part of a frame-and-fork package rather than as an isolated component.

Shell, Axle and End Caps: Reading the Material Split

The MT-013F pairs an AL6061-T6 aluminum hub shell with an AL7075 aluminum axle and end caps. That split is worth understanding because the two parts do different jobs. The shell carries the spoke flanges and the bearing bores and is the structure the wheel is laced around; the axle and end caps form the mounting interface that clamps into the fork.

AL6061-T6 is a common, well-understood aluminum for machined bicycle components, and ARC's stated manufacturing context includes CNC machining and precision manufacturing. AL7075 is a higher-strength aluminum grade often selected where a part needs more strength at a given size. In this hub, that combination is the stated construction—specifiers should treat it as a material fact to verify against drawings and samples, not as a claim that the hub will outlast any alternative in every landing scenario.

Where this matters in a dirt jump front wheel is the flange and bearing area. The hub lists S&S steel bearing options, which tells the buyer that bearing specification is a selectable point rather than an unstated default. Steel bearings are the conventional choice for this kind of application, but the exact bearing designation, sealing arrangement and service interval should be confirmed in the supplier's specification rather than inferred from the words "steel bearing."

The honest reading is this: the material split and bearing option tell a specifier what the hub is built from and what needs to be pinned down on paper. They do not, on their own, predict bearing life or fatigue performance under a given rider. Those questions belong in sample testing and in the supplier conversation.

6-Bolt Mounting and J-Bend Spoke Choices

The 6-bolt disc interface is the most standardized part of this hub, and that is its appeal. Six-bolt rotors are widely available, and a dirt jump front brake setup can be matched without adopting a proprietary mounting pattern. For brands and wheel builders already standardized on 6-bolt front rotors, the MT-013F fits into an existing parts library more easily than a center-lock hub would.

The spoke side offers more room for choice. The hub uses a J-bend spoke design and is compatible with 14G spokes, and it is available in 28H, 32H and 36H configurations. Those three counts are not interchangeable in a dirt jump context. A 36H build gives more spokes and generally more redundancy for riders who prioritize durability and are willing to accept the weight; a 32H build is a common middle ground; a 28H build reduces spoke count and suits builds where a lighter front wheel is the priority and the rider's style supports it. The right answer depends on the rider profile and the wheel's intended use, so the hole count should be chosen alongside the rim and lacing plan, not in isolation.

J-bend spokes are the traditional format and remain widely stocked by wheel builders, which helps with serviceability and replacement planning. Because the hub is 14G-compatible, spoke selection should follow the builder's normal gauge and length calculation, with the hub's flange dimensions confirmed from ARC's drawings before lacing. The MT-013F product page is the reference point for the ARC MT-013F 6-Bolt Dirt Jump Front Hub, and it is where a specifier can start the configuration conversation.

What to Confirm With ARC Before Sampling

Before a sample is built, the open points should be closed in writing. The first is the axle confirmation: 15×100mm thru-axle is the stated standard, but the fork and dropout interface, axle thread pitch and end-cap configuration should be verified against the intended frame. The second is the bearing option—S&S steel bearings are listed, so the exact bearing specification, quantity and sealing should be requested rather than assumed.

The third is drilling: 28H, 32H or 36H, matched to the rim and the rider's durability-versus-weight preference. The fourth is the spoke interface—J-bend, 14G-compatible—confirmed with flange dimensions so the wheel builder can calculate spoke length correctly. The fifth is finish and branding, since ARC's stated business includes OEM and ODM hub solutions for bicycle brands, wheel manufacturers and distributors, covering MTB and other categories. That scope makes a custom front hub specification a natural conversation, but the specific finish, laser marking and packaging terms still need to be agreed.

It is also reasonable to ask for the CAD or 2D drawing, the bearing specification sheet and the sample inspection criteria at the same time. These are ordinary OEM requests, and they let the purchasing engineer verify the stated ~206.2g weight, the AL6061-T6 shell and AL7075 axle and end caps against the actual part rather than the catalog copy.

For dirt jump and demanding MTB front wheel programs where a 15×100mm thru-axle, 6-bolt rotor mounting and a J-bend, 14G-compatible build are the fixed requirements, the ARC MT-013F is worth placing on the shortlist and evaluating as a sample. ARC's stated OEM/ODM capability and Taicang-based hub manufacturing give a specifier a direct route to confirm hole count, bearing option and finish before committing to a production order. The next step is straightforward: send the fork and frame interface details, the intended hole count and the bearing requirement to ARC, and ask for a sample built to that configuration so the material split, rotor mounting and spoke interface can be checked on the bench before the wheel goes into a full build.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China