Jump Front Hub

ARC MT-013F Dirt Jump Front Hub: AL6061-T6 Shell and AL7075 Axle Explained

20 min read
On this page 5 sections

For dirt jump and other demanding MTB front wheel builds, the material specification of the hub is often the first thing a product manager or wheelset builder checks—and the last thing that gets explained clearly. The ARC MT-013F answers that question with a deliberate split: a hub shell machined from AL6061-T6 aluminum, paired with an axle and end caps made from AL7075. Understanding why those two alloys are assigned to those two locations is the shortest route to judging whether the hub belongs in a given build or OEM program.

What the MT-013F Material Split Actually Means

The MT-013F is documented as "featuring a durable AL6061-T6 aluminum hub shell combined with a high-strength AL7075 aluminum axle and end caps." That single sentence carries the entire design logic, so it is worth unpacking rather than reading past.

AL6061-T6 is a heat-treated, magnesium- and silicon-bearing aluminum alloy. In its T6 condition it offers a practical balance of mechanical strength, corrosion resistance and machinability—properties that matter when a hub shell must be turned and bored to hold bearing seats, a disc mount and spoke flanges within tight tolerances. The T6 temper is what converts the alloy from a soft, easily formed material into a structural one.

AL7075 is a zinc-bearing aluminum alloy associated with noticeably higher strength than 6061 in comparable tempers. It is also less forgiving to machine and less corrosion-tolerant in raw form, which is why it tends to be reserved for the locations where load concentration is highest and the geometry is simplest. On the MT-013F those locations are the axle and the end caps.

Read together, the pairing is not two premium materials used for their own sake. It is a division of labor: a shell alloy selected for a durable, precisely machined body, and an axle alloy selected for strength in the part that carries the rider's load into the frame.

Why a Dirt Jump Front Hub Uses Two Different Aluminum Alloys

A dirt jump front wheel does not see the long, smooth load cycles of a road wheel. It sees short, repeated and often harsh inputs—landing forces, case impacts, and the lateral and torsional loads that arrive when a front wheel is loaded unevenly. The hub sits at the center of all of it, and the two halves of the hub experience those inputs differently.

The hub shell is a relatively thin-walled structure with several machined features: bearing bores at both ends, spoke flanges, and a 6-bolt disc interface. Its job is to hold those interfaces in alignment and distribute spoke tension and braking torque. AL6061-T6 suits that job because it can be machined into a consistent wall section and heat-treated to a stable strength level, while remaining practical to produce in volume. A shell material that is difficult to machine or prone to distortion would show up as bearing misalignment or inconsistent flange geometry—problems that surface later in the wheel build, not on a spec sheet.

The axle is a different problem. It is a slender part that transfers load from the dropout interface into the hub body, and it passes through the bearings. In a thru-axle design the hub's own axle and end caps form the interface with the fork and the thru-axle itself, so they need to resist deformation at the contact points. AL7075 is used here because higher strength in a thin, highly loaded section is the priority, and the geometry of an axle and end cap is simpler to machine than a shell.

It is worth being precise about what this reasoning does and does not establish. The material assignment is consistent with the load paths described, but alloy choice alone does not determine fatigue life, stiffness or impact resistance. Wall thickness, heat treatment consistency, machining quality, bearing fit and the spoke build all contribute. Buyers should treat the AL6061-T6 / AL7075 split as a design signal worth discussing with the supplier—not as a standalone performance guarantee.

Build Interfaces Buyers Should Confirm: 15×100mm, 6-Bolt, J-Bend and Drilling

Material choice tells you how the hub is built; the interface list tells you whether it fits. For the MT-013F, the documented configuration is a 15×100mm thru-axle standard, a 6-bolt disc brake interface, J-bend spoke design compatible with 14G spokes, and drilling options of 28H, 32H and 36H, with S&S steel bearing options and a total weight of approximately 206.2g.

Each of those points maps to a decision:

  • 15×100mm thru-axle. This is the fit check against the fork. A front hub program built around thru-axle forks must confirm the dropout standard before anything else, because it determines the end cap geometry and cannot be changed by the wheel builder.
  • 6-bolt disc mount. The 6-bolt pattern is a widely used standard, and confirming it early avoids mismatches with the rotor and brake spec chosen for the build.
  • J-bend and 14G spokes. J-bend flanges accept conventional bent-spoke heads, which keeps the hub compatible with common spoke stock and established lacing practice. 14G compatibility should be read alongside the chosen drilling.
  • 28H, 32H and 36H drilling. These are not interchangeable in planning terms. A 28H build reduces spoke count and changes the tension distribution across the flange; 36H provides more spoke positions for builds where redundancy and load sharing are prioritized. The right choice depends on the rim, the rider weight and intended use, and on the spoke availability the builder works with.
  • Approximately 206.2g. This figure should be read against the stated configuration—drilling, bearing option and end caps—rather than treated as a comparable number across different builds.

A practical sequence for a wheel builder or brand is to confirm the fork standard first, then the rotor interface, then drilling and spoke specification, and only then evaluate the weight and material details against the target build. ARC's MT-013F specification sheet, available on the product page, is the reference point for any of these figures that will appear in a brand's own documentation.

Specifying the MT-013F for OEM/ODM Front Hub Programs

For a bicycle brand, wheel manufacturer or distributor, the sourcing question is broader than whether one hub fits one build. It is whether the supplier can hold the specification across a program. That is where the material story connects to the manufacturing story.

ARC, based in Taicang, Jiangsu, China, was founded in 2013 and specializes in the research, development, manufacturing and customization of high-performance bicycle hubs, providing OEM and ODM solutions to bicycle brands, wheel manufacturers and distributors worldwide. The company's stated capabilities include CNC machining, precision manufacturing, professional engineering expertise and quality control systems—the process areas directly relevant to producing a machined AL6061-T6 shell and an AL7075 axle and end caps to a repeatable specification.

When specifying the MT-013F for a program, the useful conversation points are:

  1. Configuration lock. Confirm the drilling (28H, 32H or 36H), bearing option and end cap specification that will define the production part, and make sure each appears on the drawing and the inspection plan rather than only in correspondence.
  2. Material verification. Ask how incoming aluminum stock is identified and how heat-treated 6061-T6 and 7075 parts are distinguished through production—material mix-ups are a real risk when two alloys are machined side by side.
  3. Interface tolerances. The thru-axle interface, bearing bores and disc mount are the dimensions that determine whether the hub assembles cleanly into a wheel and a fork. These are the points to confirm against the drawing.
  4. Sample evaluation. A sample build is the appropriate place to check bearing fit, spoke hole condition and end cap seating before committing to a production run. What to measure is a matter for the buyer's own quality plan; the hub's role is to meet the agreed drawing.
  5. Customization scope. OEM/ODM discussions should establish which elements are open to change—finishes, branding, packaging, drilling mix—and which are fixed by the design. Because ARC's business covers customization as well as standard production, these questions are best raised early rather than after tooling decisions.

What the available information does not establish is MOQ, lead time, certification status or production capacity for this specific hub. Those are commercial and quality-system questions that belong in a direct supplier conversation and should be confirmed in writing before they are used in a brand's own planning.

The MT-013F is a sensible candidate for dirt jump and demanding MTB front wheel programs where a 15×100mm thru-axle, 6-bolt disc interface and J-bend spoke build are already fixed. Its AL6061-T6 shell and AL7075 axle and end caps give buyers a clear material rationale to evaluate, and ARC's position as a hub-focused manufacturer with OEM/ODM experience gives them a supplier able to discuss the specification rather than simply quote a part number. For brands and wheel builders weighing that configuration, putting the MT-013F on the sample evaluation list—and bringing the drilling, bearing and end cap questions to the first technical conversation—is a reasonable next step.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China