Dirt Jump

ARC MT-013F Dirt Jump Front Hub: Specifications and Spoke Drilling Options

15 min read
On this page 5 sections

The ARC MT-013F is a front hub intended for dirt jump and other demanding mountain bike front-wheel builds, and its specification sheet is best read as a set of build-matching decisions rather than a list of numbers. The parameters that matter most to a buyer are the 15×100mm thru-axle, the 6-bolt disc interface, J-bend spoke compatibility with 14G spokes, and the choice between 28H, 32H and 36H drilling. Each of those choices ties back to the fork, the rim and the riding duty the wheel is being built for.

What the MT-013F Is Built For

Dirt jump and aggressive MTB front wheels place a particular kind of load on a hub. Landing forces arrive through the axle and flanges, cases and sideways impacts put bending loads into the shell and axle, and the wheel is often rebuilt or re-trued rather than replaced. That duty cycle is why the MT-013F pairs a durable AL6061-T6 aluminum hub shell with a high-strength AL7075 aluminum axle and end caps. The split is deliberate: the shell needs to hold spoke holes and bearing seats under repeated load, while the axle and end caps need strength at the fork interface where the clamping and impact loads concentrate.

ARC designs the MT-013F for exactly this category, so the specification sheet maps to a defined duty rather than a generic all-round hub. For a wheel builder or brand product manager, that means the hub can be evaluated against a known use case — dirt jump and demanding MTB front wheels — before any commercial discussion begins. As part of ARC's bicycle hub OEM/ODM business, the MT-013F is also available as a platform that brands and wheel manufacturers can build around, rather than only as a catalog item.

Reading the Specification Sheet Correctly

The 15×100mm thru-axle standard is the first hard gate. A thru-axle front hub only fits a fork designed for that axle standard and width, so the fork must be confirmed before anything else — a 15×100mm hub cannot be adapted to a quick-release fork or to a different thru-axle spacing. Buyers should match this figure against the actual fork spec, not against a similar model.

The 6-bolt disc interface determines rotor compatibility. Six-bolt rotors are widely available and easy to source, and the interface is a straightforward, well-understood mounting pattern; the practical check is that the intended rotor uses six bolts rather than a centerlock mount. It is a brake-interface decision that should be settled early, because it constrains rotor choice later.

The spoke interface is J-bend with 14G compatibility. J-bend spokes are the traditional, widely stocked format, which matters for builders who want predictable spoke sourcing and straightforward lacing. A buyer should confirm that the planned spoke gauge and brand are available in the required lengths for the chosen rim and lacing pattern, since 14G compatibility describes the spoke hole and flange design, not a guarantee that any specific spoke length will be in stock.

The material split deserves attention because it is easy to misread. AL6061-T6 describes the hub shell; AL7075 describes the axle and end caps. These are different alloys serving different functions, and the specification should not be summarized as a single "aluminum hub." Bearing options are stated as S&S steel, which is a bearing specification rather than a claim about friction, durability life or service intervals.

Stated total weight is approximately 206.2g. Buyers should treat this as a reference figure rather than a fixed number, because weight varies with configuration — drilling count and small component differences can shift the final figure. It is reasonable to use 206.2g for early build estimates and to confirm the figure for the exact configuration at sampling.

Choosing Between 28H, 32H and 36H Drilling

Spoke count is the main variable in the MT-013F range, and the right choice depends on the rim, the rider and the spares situation rather than on a universal "stronger is better" rule.

A 28H build suits lighter riders and smoother dirt jump lines where weight and a livelier feel matter, but it demands a rim that is designed for that spoke count and a builder who can achieve even tension with fewer spokes. A 32H build is the common middle ground for dirt jump and demanding MTB front wheels: it offers more load-sharing points than 28H while remaining widely supported by rims and spoke inventories. A 36H build increases the number of load paths and is often chosen where the rim is heavier-duty, where the rider is heavier or harder on equipment, or where the build prioritizes resilience over weight.

The critical mismatch risk runs in both directions. A 36H hub cannot be laced to a 32H rim, and a 28H hub cannot serve a 36H rim, so the rim's drilling must be confirmed before the hub is ordered. Spoke availability is the second constraint: 14G J-bend spokes are common, but specific lengths for a given rim and lacing pattern still need to be checked. Because ARC offers the MT-013F in 28H, 32H and 36H configurations to suit different wheel-building requirements, one hub platform can cover several rim and spoke-count plans without changing model — useful for a brand running more than one front-wheel SKU.

Points to Confirm Before Sampling or Ordering

Because the specification sheet defines the platform, the remaining checks are about the specific build and the commercial arrangement. Before requesting samples, a buyer should confirm the fork's 15×100mm thru-axle compatibility, the six-bolt rotor choice, the rim's drilling count, and the availability of 14G J-bend spokes in the required lengths for the planned lacing pattern. It is also worth confirming the weight for the exact drilling configuration being ordered, since the stated figure is approximate and configuration-dependent.

The product data reviewed here does not state pricing, lead times, minimum order quantities, certification status or production capacity. Those are commercial and program questions to raise directly with ARC rather than infer from the specification sheet, and they should be treated as open items in any sourcing plan. Buyers working on a customized program can also discuss OEM and ODM requirements, since ARC's stated business covers OEM and ODM solutions for global bicycle brands, wheel manufacturers and distributors across MTB, road, gravel and e-bike categories.

For a dirt jump or demanding MTB front wheel where a 15×100mm thru-axle, 6-bolt rotor and J-bend 14G spokes are already fixed by the fork and rim, the ARC MT-013F is a sensible hub to put on the evaluation list. The 28H, 32H and 36H options let a builder match the hub to the rim rather than compromise, and the AL6061-T6 shell with AL7075 axle and end caps addresses the load path that dirt jump front wheels actually see. The productive next step is to fix the drilling and rim combination, then confirm the configuration-specific weight and commercial terms with ARC before committing to a sample.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China