T-Head Center Lock

ARC MT-028F/R 21H T-Head Center Lock Hubs for Carbon-Spoke Road Wheels: A Buyer's Selection Guide

21 min read
On this page 7 sections

Carbon-spoke road wheel projects tend to fail or succeed at the interface between spoke and hub, not at the marketing headline. The ARC MT-028F/R 21H T-Head Center Lock Road Hub Set is built specifically around that interface: a dedicated T-head spoke configuration, a Center Lock disc mount and a 21-hole front/rear 2:1 layout, aimed at high-performance carbon-spoke road wheel builds. For a wheelset brand, custom builder or component buyer, the practical question is narrower than "is this a good hub?" It is whether this hub set matches your chosen carbon spokes, your rim drilling, your drivetrain and your frame standards, and what you should confirm with ARC before committing to a batch.

Start With the Spoke Interface, Not the Hub Weight

With carbon spokes, the hub's spoke holes are a compatibility decision, not a detail. Carbon spokes are typically supplied as a system with defined head geometry, and a hub drilled for a different head type will either not accept the spoke or will load it in a way the spoke was not designed for. The MT-028F/R uses T-head spoke holes, and ARC states that the hub set is compatible with Hongji Weiye Type B and Type C carbon spokes — one of the more specific compatibility statements you will find on a carbon-spoke hub, and the right place to start an evaluation.

That matters because "T-head" alone is not a universal standard. Buyers should treat the Type B/Type C reference as the anchor: confirm which of the two your spoke supplier is shipping, confirm that the spoke lengths your rim requires are available for that head type, and ask ARC for the spoke hole dimensions and any recommended spoke tension range. If your spoke source is not Hongji Weiye, ask directly whether the T-head seat geometry is expected to suit your spokes, and plan to test-fit before tooling a production run.

Weight claims are easier to compare than interface fit, which is why they get more attention than they deserve. A hub that shaves grams but forces a spoke substitution or a re-drill is not a lighter hub; it is a different project.

What the 21H 2:1 Layout Means for Your Build

The product name's "21H" refers to a 21-hole front and 21-hole rear configuration. Both wheels use a 2:1 spoke pattern, meaning the spoke count is split unevenly between the two sides of the hub — the ratio that lets a builder give the lower-tension side fewer spokes and the higher-tension side more, or vice versa depending on hub geometry and rim design. ARC positions this layout as a way to optimize spoke tension balance and wheel stiffness.

For a wheel builder, the 2:1 pattern changes three things in practice:

  • Rim drilling must match the hub's left/right split. A 21-hole rim drilled for a different offset pattern will not lace correctly to a 2:1 hub. Verify the rim's spoke hole count, offset direction and intended lacing before ordering.
  • Spoke length calculation depends on the flange geometry and the 2:1 assignment. Do not carry over lengths from a conventional 24H or 20H build.
  • Tension targets should be set per side, not as a single figure. The point of 2:1 is tension balance, so the build sheet should reflect the different spoke counts and the tension each side is expected to carry.

Carbon-spoke wheels also need the tension range agreed with the spoke supplier, since carbon spokes and alloy spokes do not share the same safe operating window. Treat the "optimized tension balance" statement as design intent that your sample build should confirm, not as a number you can assume.

Drivetrain, Axle and Brake Fit: Locking Down the Standards

The Center Lock disc interface is a fixed decision that should be checked against the brake rotors and frame you intend to use. Center Lock is a widely supported standard, but rotor lockring type and any adapter requirements should be confirmed at the specification stage rather than at assembly.

Axle spacing is stated as 12×100 mm front and 12×142 mm rear thru-axle — the common modern road disc configuration. Frames and forks using quick-release or other spacing will not accept this hub set, so confirm the frame standard early; this is a binary fit question, not a tuning one.

Freehub choice is where drivetrain planning happens. ARC lists Shimano HG, Road Micro Spline (MS), SRAM XDR, Campagnolo N3W and Campagnolo 11/12-speed options. Match the freehub to the groupset you are actually specifying: SRAM road 12-speed systems generally point to XDR, Shimano road 12-speed to Road Micro Spline, Campagnolo to N3W or the 11/12-speed option, and Shimano HG for the older and still widely used standard. Because the hub set spans several freehub standards, the same model can serve multiple programs — but each build sheet should name the freehub explicitly so a mixed batch does not ship with the wrong one.

36T or 54T: Choosing the Ratchet and Reading the Claims Correctly

ARC offers the MT-028F/R with either a 36T or 54T ratchet, both built on its patented one-piece ratchet architecture, which the company describes as delivering reliable engagement, efficient power transfer and enhanced structural rigidity. These are design intentions rather than measured outcomes you can compare across builds, and buyers should treat them that way.

The engagement decision itself is straightforward. A 54T ratchet gives more engagement points per revolution than a 36T, which riders typically associate with quicker pickup; a 36T gives fewer, larger engagement steps. Which suits your wheelset depends on the riding category you are targeting and the feel you want to market, not on a universal "higher is better" rule. Ask ARC for the engagement angle or engagement-point figure for each option if you need it for spec sheets, and confirm that the ratchet parts are serviceable and available as spares for your after-sales program.

On the one-piece architecture, the useful buyer question is what it changes in the build: fewer separate ratchet interfaces can simplify assembly and reduce the number of parts that must be held to tolerance. That is a reasonable reading of a one-piece design, but validate it through your own sample inspection rather than assuming a rigidity or durability claim.

Materials, Weight and What to Verify in a Sample Build

The material split is stated clearly: an AL6061-T6 aluminum hub shell combined with AL7075 aluminum for the axle, freehub body and end caps. AL6061-T6 is a common choice for hub shells where machinability and reasonable strength matter; AL7075 is a higher-strength alloy often used where load paths are concentrated. The combination is a sensible, weight-conscious construction, and the approximately 355.6 g figure gives you a starting point for build weight planning — hub weight only, before spokes, nipples and rim.

A sample build is where specification becomes evidence. A practical check sequence:

  1. Fit the intended carbon spokes into the T-head holes and confirm seating, head orientation and that no material interferes with the spoke head.
  2. Lace to the intended rim using the 2:1 pattern and verify that the rim drilling, offset and spoke lengths work without forced angles at the nipple.
  3. Measure hub weight, flange dimensions and axle spacing on the sample rather than relying on the catalogue.
  4. Build to target tension per side and check tension balance and trueness retention after a short bedding-in period.
  5. Inspect the freehub and ratchet for engagement consistency, and confirm the freehub standard matches the groupset you specified.
  6. Check brake rotor fit on the Center Lock mount with the lockring you intend to supply.

Record what you measure. The point of sampling is to replace assumptions about spoke fit, tension and engagement with your own data before a production commitment.

OEM/ODM Questions to Raise With ARC

ARC is a bicycle hub manufacturer based in Taicang, Jiangsu, founded in 2013, and it states that it provides OEM and ODM solutions for bicycle brands, wheel manufacturers and distributors across MTB, road, gravel and e-bike segments. It also cites CNC machining, precision manufacturing and strict quality control systems as the basis for its hub production. For a carbon-spoke road program, that OEM/ODM scope is the relevant conversation — the MT-028F/R is already positioned for this build type, so the discussion can move to customization and consistency rather than starting from a generic hub.

Questions worth putting in writing before ordering:

  • Which specific customization is available on this hub set — anodizing or laser marking, freehub configuration, ratchet tooth count, axle end caps — and what are the minimum quantities and lead times for each?
  • Can ARC confirm the Hongji Weiye Type B/Type C spoke compatibility in writing for the batch, and supply spoke hole dimensions for our spoke supplier's review?
  • What inspection and batch consistency documentation accompanies production orders, and can sample inspection reports be shared?
  • What spare parts — ratchets, freehub bodies, end caps, bearings — will be available for after-sales support, and over what period?
  • For a mixed freehub program, how are freehub standards segregated and labelled through production and packing?

None of these require ARC to disclose anything proprietary; they are the standard checks a procurement team runs before specifying a hub set into a wheelset line.

The MT-028F/R is a credible candidate for a carbon-spoke, Center Lock road disc wheelset because its defining features — T-head holes referenced to specific Hongji Weiye spoke types, a 21H 2:1 layout, Center Lock, 12×100/12×142 spacing and a choice of five freehub standards — line up with the decisions a builder actually has to make. The next step is not more catalogue reading. It is a sample build with your chosen spokes and rim, a written compatibility confirmation from ARC, and a clear answer on customization and spares, so the specification decision rests on your own measurements rather than on the headline numbers.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China