MTB Hub

ARC MT-051F/R 28H Boost 6-Bolt MTB Hub Set: Specifications and Build Configuration

16 min read
On this page 6 sections

Wheel builders and product teams working on a trail or all-mountain wheelset usually reach the same checkpoint early: the frame has already set the dropout standard, the rim has already set the spoke count, and the drivetrain has already set the freehub body. A hub set either satisfies all three at once or forces a redesign. The ARC MT-051F/R 28H Boost 6-Bolt MTB hub set is built around that exact checklist, which makes it worth reading as a set of parameters rather than a single component.

What the MT-051F/R Is Built For

The MT-051F/R is a Boost-spacing mountain bike hub set intended for modern trail and all-mountain wheel builds. Its defining structural choice is a straight-pull spoke configuration rather than a conventional J-bend layout, paired with a lightweight overall package of approximately 258.6g for the set.

That positioning matters for specification work. Trail and all-mountain wheelsets typically balance three competing demands: lateral stiffness under cornering and braking loads, a spoke count that keeps the rim and hub flange partnership sensible, and a weight budget that does not undermine climbing performance. A straight-pull hub set changes how the builder approaches the first and third of those, because spoke selection, lacing pattern and tensioning practice all follow from the hub's flange design.

For bicycle brand product managers and wheelset builders, the practical question is not whether the hub set is "good" in isolation, but whether every one of its interfaces lines up with the frame, rim and drivetrain already chosen for the project. ARC manufactures hubs and supplies OEM and ODM programs, so the MT-051F/R is best evaluated as a production component that can be specified into, or sampled for, a defined build.

Boost Spacing and 28H Configuration

Two parameters in this hub set are most likely to decide fit before anything else is considered.

The first is spacing. The MT-051F/R uses 15×110mm front and 12×148mm rear Boost spacing. Buyers should confirm both against the frame specification rather than assuming that "Boost" alone settles it, since front and rear Boost standards are defined separately and both must match. The rear 12×148mm figure in particular determines dropout width and axle standard, and a mismatch here cannot be corrected later in the build.

The second is drilling: 28H front and rear. A 28-hole count is a deliberate middle position. It is higher than the lightest cross-country counts and lower than the heavier-duty counts sometimes used on aggressive builds, which is consistent with a trail and all-mountain remit. In practice, the builder should confirm that the intended rims are available in 28H and that the chosen spoke type and lacing pattern are appropriate to a straight-pull hub before committing to the plan.

Because both spacing and hole count are fixed features of the hub set rather than options, they are the correct starting point for any fit check. Get them wrong and no amount of downstream specification work recovers the build.

Straight-Pull Structure and Materials

The straight-pull structure is the feature that most changes how a wheel is assembled. Straight-pull spokes run directly from the hub flange to the rim without a J-bend at the head, and the hub's flange design must be matched with the correct spoke type and length. Builders familiar with J-bend hubs should treat spoke specification as a separate, deliberate step here rather than carrying over an existing spoke list.

The material breakdown supports the weight and durability targets:

  • AL6061-T6 aluminum hub shells — a common, well-understood shell alloy chosen for a balance of strength and machined precision.
  • AL7075 aluminum axle, freehub body and end caps — a higher-strength aluminum grade used across the load-bearing and drivetrain-engagement parts.

This is a coherent material story for a lightweight trail hub set: aluminum throughout, with the higher-strength grade reserved for the axle and freehub where loads concentrate. Buyers comparing this hub set against alternatives should note that the material list alone does not establish fatigue life or service intervals; those depend on riding conditions, spoke tension practice and maintenance, and are worth confirming directly with the supplier during sample evaluation.

Drivetrain and Brake Interface Choices

The MT-051F/R is designed to fit the three dominant mountain bike freehub standards: Shimano HG, Micro Spline and SRAM XD. That breadth is a genuine procurement advantage for anyone building wheelsets across multiple drivetrain platforms or supplying distributors who stock several groupset families. The correct step is to confirm which freehub body is specified per order, because the hub set's compatibility does not mean a single delivered unit covers all three.

On the braking side, the hub set uses a 6-bolt disc interface. This determines rotor mounting and should be checked against the rotors planned for the build. Builders standardized on Center Lock will need to account for the difference at the specification stage rather than at assembly.

For product teams, the sensible approach is to lock the freehub standard and rotor interface into the purchase specification explicitly, alongside spacing and hole count. These are the four parameters that define whether the hub set can be built into the intended wheel at all.

Engagement, Bearings and Weight in the Build Decision

The remaining specifications shape how the finished wheel is expected to feel and how it should be evaluated in a sample.

The hub set uses a 6-pawl, single-tooth engagement system, which ARC describes as providing responsive pickup and reliable power transfer for off-road riding. For buyers, the relevant question is whether the engagement character suits the intended riding style and whether the pawl and ratchet arrangement is serviceable within the program's maintenance expectations. These are appropriate points to raise during sample testing rather than to infer from the specification sheet alone.

S&S steel bearing options are listed as a configurable element. Bearing selection affects friction, service life and maintenance planning, and the option structure should be clarified per order so that the specification matches the intended use and the distributor's service model.

At approximately 258.6g for the set, the MT-051F/R sits in a competitive weight position for a Boost trail hub set, consistent with its aluminum construction and straight-pull design. Weight should be read as one input among several: rim choice, spoke count and build quality will influence the finished wheelset's performance at least as much as hub mass.

Taken together, the MT-051F/R gives wheel builders a hub set whose key parameters — 15×110mm and 12×148mm Boost spacing, 28H drilling, 6-bolt rotor mount, straight-pull structure, AL6061-T6 shells with an AL7075 axle and freehub, 6-pawl engagement, selectable Shimano HG, Micro Spline or SRAM XD freehub bodies, S&S steel bearing options and roughly 258.6g — can be checked against a trail or all-mountain build plan in a single pass. Teams whose frame, rim and drivetrain choices already align with those figures have a practical reason to request a sample or quotation from ARC and to confirm freehub and bearing configuration as part of the order specification. The ARC MT-051F/R 28H Boost 6-Bolt MTB Hub Set is the appropriate starting reference for that evaluation.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China