The ARC MT-075FB/RB Road Hub Set is designed for modern road disc wheel builds, featuring a straight-pull spoke design with a Center Lock brake interface. For product managers and wheelset engineers, the useful question is not simply whether this hub set exists in a road disc configuration, but whether its axle spacing, rotor mount, spoke count and freehub options line up with the frame, brake system and drivetrain that the finished wheelset must serve. Working through those gates in sequence is the fastest way to decide whether the MT-075FB/RB belongs on a specification sheet or sample request.
Start With the Frame and Brake Interface
The first checks are the ones that cannot be changed later without a new frame or a new hub. The MT-075FB/RB uses 12×100mm front and 12×142mm rear thru-axle spacing, which is the common modern road disc standard rather than quick-release or older axle formats. A wheel program built around this hub set therefore needs frames and forks confirmed for those axle dimensions, and the same confirmation should extend to any complete-bike platforms the wheelset is intended for.
Rotor mounting is the second gate. The Center Lock interface means the brake rotor attaches through a splined, lockring-based system rather than a six-bolt pattern. That choice affects the rotor specification, the tooling used at assembly, and the service instructions that go out with the wheelset. It does not by itself determine braking performance, which depends on the full rotor, caliper and pad combination, but it does fix which rotors a buyer can specify.
Getting these two facts settled first avoids the common planning error of choosing spoke counts and freehub bodies before confirming that the hub will physically fit the intended frameset.
Why 24H Straight-Pull Matters in Wheel Planning
The MT-075FB/RB is a 24-hole front and rear configuration with straight-pull spokes. In planning terms, 24H is a relatively lean spoke count that suits road disc wheelsets where weight and aerodynamic profile are priorities, and where the rim and build method are chosen to work with that count. It is not a universal answer for every rider or load case; heavier riders, rough-surface use or high-load applications may call for different build decisions. The point for a product team is that 24H must be matched to the rim's drilling and to the intended use profile from the start.
Straight-pull geometry changes how the spoke sits relative to the flange. Rather than a J-bend hooking through a drilled flange hole, the straight-pull spoke runs directly from hub to rim without the bend. For builders, this typically means the spoke length and lacing pattern must be calculated for this specific hub geometry, and the hub's flange dimensions become a required input for the wheel-building specification. Because spoke length errors are costly in a production run, confirming the straight-pull geometry against the chosen rim and lacing plan belongs in the sample stage rather than after tooling is committed.
Freehub and Drivetrain Options to Confirm
Drivetrain compatibility is where a hub set either opens up a program or narrows it. The MT-075FB/RB supports Shimano HG, Road Micro Spline (MSR), SRAM XDR, Campagnolo N3W and Campagnolo 11/12-speed freehub standards. That spread lets a wheelset brand offer the same hub platform across several groupset families, but each variant needs to be specified and stocked deliberately.
A practical approach is to map the freehub options to the actual groupsets the wheelset will be sold with, then confirm which bodies are needed for the initial production batch and which are held as service spares. It is also worth confirming with the hub supplier how the freehub body is fitted and replaced, because freehub wear and drivetrain changes are both routine events in the life of a wheelset. These are specification and service questions to settle during evaluation rather than assumptions to carry into a purchase order.
Materials, Engagement and Weight as Specification Inputs
The stated construction of the MT-075FB/RB is an AL6061-T6 aluminum hub shell combined with a high-strength AL7075 aluminum axle, freehub body and end caps. The material split is a sensible one to note in a specification review: the shell carries the spoke loads and bearing seats, while the axle and end caps sit in the load path and at the frame interface. Buyers should read these as stated material facts and confirm the tolerances and surface treatment expectations with the supplier for their own program.
Engagement is handled by a 6-pawl, single-tooth system, which is presented as providing responsive pickup and consistent power transfer. For a wheel program, the relevant question is whether that engagement behaviour suits the intended riding category, and how the ratchet mechanism is serviced over time. These should be verified through sample testing rather than inferred from the pawl count alone.
The total weight is approximately 345.2g for the hub set, and S&S steel bearing options are listed. Weight and bearing choice should be evaluated against the complete wheel build, since rim, spokes and rotor choice will dominate the final figure. It is also worth confirming which bearing option is specified per order, because bearing selection can affect both feel and long-term service expectations.
Moving From Specification Check to OEM/ODM Discussion
Once the frame interface, rotor mount, spoke configuration, freehub variant and material specification have been checked against the intended wheel program, the remaining question is supply. ARC, based in Taicang, Jiangsu, China and founded in 2013, manufactures bicycle hubs and provides OEM and ODM solutions for bicycle brands, wheel manufacturers and distributors across MTB, road, gravel and e-bike applications. That positioning fits a wheelset program that needs a hub platform adapted to its own rim, lacing and groupset requirements rather than an off-the-shelf part.
The MT-075FB/RB is a good candidate for that conversation when the program is a road disc wheelset built around 12×100mm and 12×142mm thru-axles, Center Lock rotors, 24H straight-pull lacing and one or more of the listed freehub standards. ARC's stated CNC machining, precision manufacturing and quality control capabilities are relevant to repeatable hub supply, but the specifics that matter to a buyer, such as tolerances, inspection criteria, sample quantities and production scheduling, should be confirmed directly during the OEM/ODM discussion.
For teams evaluating this hub set, the practical next step is to assemble the frame, rotor, spoke and groupset requirements into a single specification sheet, then request samples matched to that specification. The ARC MT-075FB/RB 24H Straight-Pull Center Lock Road Hub Set is worth including as a lead candidate where those requirements align, with sample verification and OEM/ODM terms settled before the design is locked into a production wheelset.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China