ARC MT-080F/R

ARC MT-080F/R 20/24H Hub Set Specs for Carbon-Spoke Road Wheels

16 min read
On this page 6 sections

For a wheel brand developing a lightweight road disc wheelset around carbon bladed spokes, the hub platform often determines whether the build can hit its stiffness, weight and drivetrain targets. The ARC MT-080F/R 20/24H Center Lock road hub set is documented as a dedicated carbon-spoke platform, so its specifications deserve a line-by-line reading before any sample or OEM/ODM discussion begins. This article walks through the published numbers and then converts them into fit checks that engineers can act on.

What the MT-080F/R Is Built For

The MT-080F/R is positioned specifically for lightweight road disc carbon wheel builds, using a compact small-flange architecture and a carbon-spoke interface rather than a general-purpose spoke drilling. That focus matters in procurement terms: a hub set intended for round-head carbon bladed spokes changes the spoke hole geometry, the lacing recommendation and the spoke tension strategy compared with a standard steel-spoke J-bend or straight-pull hub.

For a road disc wheelset program, the target is usually a shallow-to-mid-depth carbon rim paired with bladed spokes and a disc brake interface, where the hub must keep weight low without compromising axle stiffness or freehub durability. The MT-080F/R specification sheet addresses each of these load paths—spoke interface, shell material, axle, ratchet and brake mount—so engineers can judge fit against their own rim and spoke choice before committing tooling or order volumes. ARC manufactures hubs from its Taicang, Jiangsu base and runs OEM/ODM hub programs, which is the relevant background when a brand needs a documented platform plus customization discussion rather than an off-the-shelf catalog item.

Spoke Count, 2:1 Lacing and the 4.2mm Spoke Interface

The most build-critical numbers are the spoke counts and the spoke hole specification. The hub set uses 20 holes at the front and 24 at the rear, with a 2:1 spoke arrangement. In practice, 2:1 lacing groups spokes so that one side of the hub carries twice the spoke count of the other, which is a common way to balance tension between the drive and non-drive sides of a rear wheel and between the disc and non-disc sides of a front wheel. ARC's own description states that this 20H/24H configuration with a 2:1 arrangement helps optimize spoke tension balance and load distribution—useful context, but engineers should still confirm the arrangement against their rim's drilling pattern, because a rim designed for a different spoke ratio cannot simply adopt a 2:1 hub.

The spoke holes are specified at 4.2mm and are intended for compatible round-head carbon bladed spokes, with VONOA and Hongji Weiye configurations cited as reference examples. This is a detail worth flagging during sourcing: spoke hole diameter and head-seat geometry must match the actual spoke model chosen, since an oversized or undersized interface can affect seating, fatigue life and wheel truing. Before sampling, it is sensible to send the exact spoke drawing—head shape, diameter and blade dimensions—to ARC so the interface can be confirmed against the intended spoke supply, rather than assuming compatibility from the hole size alone.

Shell, Axle and Drivetrain Configuration

The structural specification combines a forged AL6061-T6 aluminum hub shell with AL7075 axles, freehub body and end caps. Forged AL6061-T6 is a familiar choice for hub shells where a balance of strength and low weight is needed, while AL7075 is used in the axle and freehub body for higher strength in the highly loaded drivetrain and axle paths. These are material designations, not performance guarantees; actual stiffness and durability depend on wall thickness, heat treatment, machining tolerance and the complete wheel build, so the material list should be read as a design intent rather than a test result.

The ratchet system is a patented one-piece design offered in 36T and 54T. Tooth count affects engagement angle and, in general terms, a higher tooth count gives quicker engagement while a lower count can suit riders prioritizing lower drag or different feel—but the choice should be matched to the intended riding category and validated in the complete wheel, not inferred from tooth count alone. The brake interface is Center Lock, which simplifies rotor mounting and alignment, and the axle spacing is 12×100mm front and 12×142mm rear thru-axle, the common road disc standard. Any frame or fork with a different spacing, or a quick-release dropout, falls outside this configuration and would need a separate discussion rather than an adapter assumption.

Freehub and Bearing Choices for a Wheelset Program

The freehub standard is one of the clearest variables a brand can lock down early, because it determines drivetrain compatibility for the finished wheelset. The MT-080F/R supports Shimano HG, Road Micro Spline, SRAM XDR, Campagnolo N3W and Campagnolo 11/12-speed freehub standards. A single hub platform covering this range is useful for a wheel program sold across multiple groupset ecosystems, but each freehub body is a distinct part, so the specification should be confirmed per SKU rather than assumed to be interchangeable.

Bearing options are listed as S&S steel, ENDURO and CeramicSpeed. These represent different bearing supply routes, and the choice will usually follow the price tier and service expectations of the wheelset rather than a single "best" option. The listed complete hub set weight is approximately 333.8g. As with any listed weight, it should be treated as a reference figure for the hub set as specified, and engineers should confirm the weight of the exact configuration—freehub, bearing option and axle specification—they intend to order, since component choices can change the final figure.

Fit Checks Before Sampling or Ordering

With the published specification in hand, the practical next step is a verification list rather than an immediate order. The following points are the ones most likely to affect whether the MT-080F/R suits a given carbon-spoke wheelset:

  • Spoke count and rim drilling: confirm the rim is drilled for 20H front and 24H rear, and that its spoke ratio is compatible with the hub's 2:1 arrangement.
  • Spoke interface: match the 4.2mm spoke holes and round-head geometry to the exact carbon bladed spoke model, providing the spoke drawing for confirmation.
  • Axle and frame compatibility: verify 12×100mm front and 12×142mm rear thru-axle dropouts on the intended frame and fork, and rule out quick-release or other spacing.
  • Brake mount: confirm Center Lock rotor compatibility and the intended rotor sizes for the frame.
  • Drivetrain: select the freehub standard—Shimano HG, Road Micro Spline, SRAM XDR, Campagnolo N3W or Campagnolo 11/12-speed—against the groupset the wheelset will ship with.
  • Ratchet and bearing specification: decide between 36T and 54T ratchet, and between S&S steel, ENDURO and CeramicSpeed bearings, according to the wheelset's price tier and service plan.
  • Weight target: request the weight of the exact configuration being considered, since the listed 333.8g refers to the hub set as specified.

These checks are best handled directly with ARC as part of an OEM/ODM conversation, where the spoke, freehub, bearing and ratchet choices can be confirmed together against the intended carbon-spoke road disc build. For brands and wheel builders whose design centers on lightweight carbon bladed spokes, Center Lock disc braking and 12mm thru-axles, the MT-080F/R is a well-documented platform worth placing on the shortlist for sample evaluation, with the carbon-spoke interface and 2:1 lacing as the specific points to validate first.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China