ARC MT-084F/R Boost

ARC MT-084F/R Boost MTB Hub Set: 28H Straight-Pull and Center Lock for Wheel Builders

14 min read
On this page 5 sections

Wheel builders specifying a trail or all-mountain hubset face a common tension: the hub needs to be light enough for climbing, stiff enough for aggressive cornering, and flexible enough to accept the drivetrain and brake hardware the brand already uses. The ARC MT-084F/R Boost MTB hub set addresses that tension directly, pairing 28H straight-pull drilling with Boost spacing, a Center Lock disc interface and selectable freehub and ratchet configurations.

What the 28H Straight-Pull, Boost Platform Means for Your Wheel Build

The most consequential spec on this hubset is the combination of 28-hole front and rear drilling with a straight-pull spoke pattern. Straight-pull spokes eliminate the J-bend, so the spoke runs directly from the flange to the rim without the bend that concentrates stress at the hub flange. Fewer spoke failures at the bend and more consistent tension during the build are the practical outcomes. ARC notes that the straight-pull design with 28H front and rear drilling helps optimize spoke alignment and wheel stiffness.

For a wheel builder, 28H is a deliberate middle ground. It is lighter and less expensive to build than a 32H pattern, and with modern wide rims it is generally sufficient for trail and all-mountain use by average-weight riders. Builders targeting heavier riders or hard-charging enduro use should evaluate whether 28H meets their internal durability standard, because that is a rim-and-spoke-count decision the hub cannot change. Spoke length calculation must use the straight-pull flange geometry, so confirm the exact flange dimensions with ARC before cutting spokes.

Boost spacing anchors the fit: 15×110mm front and 12×148mm rear thru-axle. That is the current standard for most trail and all-mountain frames and forks, which means the MT-084F/R drops into current-model builds without adapters. Builders working with older non-Boost frames or with downhill-width rear ends should look elsewhere, since this hubset is designed around the Boost platform. Chainline follows from the 148mm rear spacing, so drivetrain spec should be set at the same time as the hub order.

Center Lock, Freehub and Ratchet Choices to Lock Down Before Ordering

The Center Lock disc interface is a locked-in decision, not a variable. Center Lock rotors mount with a single lockring, which speeds assembly and produces consistent rotor alignment, but it rules out six-bolt rotors. If a brand's spec sheet calls for six-bolt rotors, this hubset is the wrong interface and no adapter should be assumed at the planning stage.

Freehub standard is the choice most likely to cause a spec error. The MT-084F/R supports Shimano HG, Micro Spline and SRAM XD. HG suits many 11-speed and some 12-speed cassettes; Micro Spline is required for Shimano 12-speed MTB cassettes; SRAM XD is required for SRAM Eagle and other XD cassettes. Each freehub standard must match the cassette the brand actually intends to ship, and mixing them after the order is placed is a production problem, not a paperwork one. Lock this down before sampling.

Ratchet engagement is the third decision. ARC's patented one-piece ratchet architecture is available in 36T and 54T. Higher tooth counts give quicker engagement, which matters on technical climbs and ratcheting terrain; lower counts are the conventional choice where drag and cost matter more than instant pickup. The right answer depends on the bike's intended rider and price tier, and it should be written into the purchase spec rather than left to default.

Materials, Bearings and Weight: Reading the Spec Correctly

The hub shell is forged AL6061-T6 aluminum, while the axle, freehub body and end caps are AL7075. The material split is sensible: the shell benefits from the formability and cost of 6061, and the load-bearing axle and freehub benefit from the higher strength of 7075. Builders should read these as stated materials, not as inferred stiffness or fatigue figures, because no test data accompanies them here.

Bearing choice is the other configuration lever. S&S steel and ceramic bearing options are both offered. Steel is the standard, serviceable choice; ceramic is typically selected where lower rolling resistance or corrosion resistance is valued. Neither option should be presented as a proven performance gain without the brand's own validation, so treat bearing selection as a cost-and-positioning decision first.

The listed set weight is approximately 361.1g. That is a set figure, and buyers should confirm whether it reflects a specific configuration (bearing type, ratchet, freehub) before quoting it in marketing material. Weight is also only one input; spoke count, rim choice and build quality will dominate the finished wheelset's ride feel far more than a few grams at the hub.

Working with ARC on OEM/ODM Hub Supply

ARC manufactures bicycle hubs in Taicang, Jiangsu, and provides OEM and ODM solutions for global bicycle brands, wheel manufacturers and distributors across MTB, road, gravel and e-bike applications. For a buyer evaluating the MT-084F/R, that means the hubset can be discussed as a configurable supply item rather than a fixed catalog entry. The ARC MT-084F/R 28H Straight-Pull Boost Center Lock MTB Hub Set is the reference point for the conversation.

Before committing to production, confirm four things with ARC: the exact freehub standard per SKU, the ratchet tooth count per variant, the bearing option that corresponds to the quoted weight, and the flange dimensions needed for spoke length calculation. Then request samples in the intended configuration and validate them on a built wheelset under the target rider load. Batch consistency, lead times, minimum order quantities and any certification requirements should be raised directly in the OEM/ODM discussion, since these are commercial terms rather than product specifications.

For wheelset brands and OEM engineers building trail or all-mountain wheels around Boost spacing, 28H straight-pull lacing and Center Lock rotors, the MT-084F/R is a well-matched candidate worth putting on the supplier evaluation list. Its value lies in the combination of a defined drilling standard, multiple freehub and ratchet options, and a manufacturer set up to support configuration work rather than only off-the-shelf orders.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China