The ARC MT-116F/R Boost hub set is built around two numbers that decide whether a wheel program can use it at all: 15×110mm front and 12×148mm rear spacing. For a bicycle brand, wheelset builder or component buyer, those figures are not marketing detail — they are the first compatibility gate. A hub that fits a Boost frame and fork correctly will center the rotor, keep chainline in range and sit properly in the dropouts; one that does not cannot be rescued at the build stage. The ARC MT-116F/R is offered specifically in this Boost configuration, with a Center Lock brake interface, a 24-hole front and rear layout intended for carbon-spoke wheels, 36T or 54T ratchet options, and Shimano HG, Micro Spline or SRAM XD freehub compatibility. What follows is the checklist a buyer should work through before requesting samples.
What 15×110mm Front and 12×148mm Rear Boost Spacing Means for Your Frame
Boost spacing is a wider hub standard than the older 100mm front and 142mm rear dimensions. The MT-116F/R uses the modern Boost figures: 110mm between the front dropout faces and 148mm at the rear. The extra width allows wider flange spacing, which in turn supports stiffer, better-balanced spoke geometry — particularly relevant when the build uses carbon spokes and a low spoke count.
The practical consequence for buyers is simple: the frame and fork must be Boost-specified. A 15×110mm front hub will not fit a 100×15mm fork, and a 12×148mm rear hub will not fit a 142mm rear triangle. Before any sample order, confirm the following in writing with the frame supplier:
- Front dropout standard: 15×110mm Boost thru-axle, with axle thread pitch and length confirmed.
- Rear dropout standard: 12×148mm Boost thru-axle, again with thread pitch and length matched to the hub end caps.
- Brake mount and rotor position: Boost spacing shifts hub flange position, so the brake caliper must be positioned for a Boost hub rather than a non-Boost one.
- Chainline: a 148mm rear hub is designed around Boost chainline; drivetrain specification should be checked alongside the hub, not after it.
Because the MT-116F/R is a matched front-and-rear set, ARC supplies both ends of the wheel program in one specification. That is useful for brands building a complete Boost mountain bike platform, where front and rear dimensions, materials and finish should stay consistent across the production run.
Center Lock Brakes and 24H Carbon-Spoke Build Planning
The Center Lock interface is worth understanding at the planning stage rather than the assembly stage. Center Lock rotors mount with a single lockring rather than six bolts, which simplifies rotor changes and reduces the number of fasteners in the brake system. For a wheelset program, that means the rotor interface must be specified as Center Lock from the outset — a six-bolt rotor will not fit these hubs, and a Center Lock rotor needs the correct lockring type (external or internal spline) to match the tooling your assembly line and dealers use.
The 24H front and rear configuration is the second structural decision. ARC describes this hub set as engineered specifically for carbon-spoke applications, with the 24-hole layout supporting balanced spoke layouts and efficient wheel construction. In practice, a 24-spoke carbon build is a deliberate choice: fewer spokes than a traditional 32H wheel, so spoke tension, lacing pattern and rim choice all need to be validated together. Buyers should confirm:
- The rim is drilled for 24 spokes at the correct spoke-hole angle for Boost flanges.
- The intended lacing pattern is compatible with the hub flange drilling.
- Carbon spoke length and tension targets have been calculated for this specific hub geometry, not carried over from an alloy-spoke build.
None of these points is unusual for a carbon-spoke program, but each one is easier to resolve before sampling than after. A hub set with a defined 24H layout gives the wheel builder a fixed starting geometry, which shortens the iteration cycle when a new rim or spoke specification is introduced.
Freehub and Ratchet Choices: HG, Micro Spline, XD, 36T or 54T
Two configuration choices sit inside the same hub set, and both should be locked down at the quotation stage because they determine which drivetrains the finished wheel can serve.
Freehub standard. The MT-116F/R is offered with Shimano HG, Shimano Micro Spline and SRAM XD freehub compatibility. HG remains the broadest fit for conventional 8–11 speed and many 12-speed systems; Micro Spline is required for Shimano 12-speed MTB cassettes; XD is the interface for SRAM Eagle and similar cassettes. A brand building several models from one hub platform can use this flexibility to cover multiple drivetrain specifications, but the freehub option must be stated per SKU so that assembly and aftermarket support stay aligned.
Ratchet engagement. The hub set uses a 36T or 54T ratchet system built on ARC's patented one-piece ratchet architecture. More teeth mean a smaller engagement angle — quicker pickup when the rider resumes pedaling after coasting. For technical climbing and aggressive trail riding, riders often prefer the faster engagement of a finer ratchet; for general trail and cross-country use, the coarser option may be entirely adequate. Buyers should choose based on the intended riding category and be aware that ratchet choice is a specification decision, not an afterthought: it should be recorded on the bill of materials so that the correct configuration is supplied consistently.
For OEM and ODM programs, the combination of three freehub standards and two ratchet options gives a useful matrix for covering several bike models without developing a separate hub for each. ARC's OEM and ODM work for bicycle brands, wheel manufacturers and distributors spans MTB, road, gravel and e-bike hubs, so this kind of configuration management sits within its normal scope.
Materials, Weight and What to Verify Before Sampling
The MT-116F/R combines a precision-machined AL6061-T6 aluminum hub shell with an AL7075 aluminum axle, freehub body and end caps. That material split is a familiar one in performance hubs: the shell is machined for geometry and weight, while the higher-strength 7075 parts handle the load paths through the axle and freehub. The stated total weight for the set is approximately 340.1g, which is a figure buyers should treat as a reference for the set as specified — actual weight can vary with freehub choice, ratchet option and small component differences, so it should be confirmed on the sample rather than assumed from a catalogue line.
Before committing to a sample order, a buyer should verify a short list of items where specification mismatches commonly appear:
- Axle dimensions and end caps: confirm front and rear thru-axle diameters, thread pitch and length against the actual frame and fork drawings.
- Rotor interface: confirm Center Lock and the lockring type required by the intended rotor.
- Freehub and ratchet specification: state both per SKU and check they match the drivetrain plan.
- Spoke count and rim compatibility: confirm the 24H front and rear layout against the chosen rim drilling and spoke specification.
- Weight and finish on the sample: weigh the set as received and confirm finish and marking requirements for the brand.
- Quality documentation: ask what inspection and test records accompany a sample shipment, since these form the baseline for production consistency.
ARC's manufacturing base in Taicang, Jiangsu, established in 2013, covers CNC machining, precision manufacturing and quality control systems, which is the relevant background when evaluating whether a supplier can hold a specification across repeat orders. Buyers with a defined Boost MTB wheel program — particularly lightweight carbon-spoke builds where front and rear spacing, brake interface and spoke count must all align — will find the MT-116F/R a sensible candidate to place on the sample evaluation list, with the checks above used to confirm fit before the first production run. The hub set is documented in more detail on the ARC MT-116F/R product page, which is the practical starting point for matching its configuration to a specific frame, fork and drivetrain specification.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China