Road Disc

ARC MT-116F/R Carbon Spoke Center Lock Hub Set: 36T vs 54T Ratchet for Road Disc Wheels

19 min read
On this page 6 sections

The ARC MT-116F/R is a carbon-spoke, Center Lock road disc hub set built for ultra-light wheelsets, and the most consequential specification decision is the ratchet: 36T or 54T. Both use ARC's patented one-piece ratchet architecture, so the choice is not about quality tiers but about how quickly the drive engages and how that suits a given rider and wheel program. For most road disc builds where smooth power delivery and low drag matter more than instant pickup, 36T is the sensible default; 54T makes more sense when the wheel program targets criterium-style acceleration or riders who notice the gap before engagement. This guide sets out what the MT-116F/R actually is, how the two ratchet counts differ in practice, and which interface, freehub, axle and bearing points to verify before requesting a sample.

What the MT-116F/R Is Designed For

The MT-116F/R is a road disc hub set intended for carbon-spoke wheels where low weight and controlled spoke tension are the primary design goals. ARC builds it around a precision-forged AL6061-T6 aluminum hub shell, with the axles, freehub body and end caps machined from high-strength AL7075. That material split is worth noting at the specification stage: the shell carries the spoke loads and bearing seats, while the AL7075 parts handle the higher local stresses of the axle and drive interface.

The set is listed at 20H front and 21H rear, uses a Center Lock disc interface, and runs 12×100mm front and 12×142mm rear thru-axle spacing. Complete hub set weight is approximately 281.1g. For a wheel builder, those numbers define the starting envelope: a road disc build with a modest spoke count, modern thru-axle standards and a weight budget that leaves room for a carbon rim and spokes.

Because the hub set is specified around carbon spokes rather than conventional steel spokes, the interface details matter as much as the weight. The MT-116F/R uses dedicated T-head spoke holes, and the rest of this guide deals with how those holes, the ratchet and the freehub options combine into a build sheet.

36T vs 54T: Choosing Ratchet Engagement

Ratchet tooth count sets the engagement angle — the amount of rotation before the drive engages. More teeth mean the ratchet picks up sooner; fewer teeth mean a larger step between engagement points. That is the mechanical reality, and it is a trade-off rather than a ranking. A 54T ratchet does not automatically make a wheel faster, and a 36T ratchet does not automatically make it more durable; both outcomes depend on the ratchet design, materials, lubrication and the loads the wheel actually sees.

What the MT-116F/R contributes to that trade-off is consistency of architecture. ARC's patented one-piece ratchet design is offered in both 36T and 54T, so a wheel brand can treat engagement as a configuration variable within one hub platform rather than switching to a different drive system. The one-piece construction is described by ARC as supporting consistent engagement, efficient torque transfer and reliable load distribution — claims that belong to the ratchet design, not to a tooth count.

In selection terms, the practical split looks like this:

  • 36T suits the majority of road disc programs where the priority is a well-rounded drive feel, and where the wheel will be used for endurance riding, rolling terrain and general road training. The larger engagement step is a normal characteristic of the design, not a defect.
  • 54T suits programs aimed at riders who value fast pickup — crit racing, punchy group riding, or any application where the rider is repeatedly transitioning between coasting and applying power. The finer step reduces the rotational gap before engagement.

Two cautions belong here. First, engagement feel is also shaped by the freehub and the rider's cadence, so tooth count should be confirmed in a sample build rather than chosen from a spec sheet alone. Second, do not translate tooth count into a claim about drag, durability or watt savings without test data; those are separate questions that a sample evaluation should address directly.

Carbon Spoke Interface and 1:1 or 2:1 Layouts

The carbon-spoke interface is where the MT-116F/R gives wheel designers the most room. The hub uses dedicated T-head spoke holes that accommodate compatible carbon spokes in 3.3mm and 5.2mm widths. That matters because carbon spokes are not interchangeable at the hub end: the T-head geometry, the slot width and the hole orientation all need to match the spoke the builder intends to use. Confirming the spoke width against the hub's hole specification is a first-order compatibility check, not a detail to settle later.

The set also supports both 1:1 and 2:1 spoke configurations. The layout choice interacts directly with the goals a wheel brand is trying to hit:

  • 1:1 lacing distributes spoke count evenly between the two hub flanges and is a familiar starting point for balanced builds.
  • 2:1 lacing groups spokes asymmetrically, which builders use when they want to manage the tension imbalance created by the disc brake and cassette on the rear wheel.

Neither layout is inherently better. What matters is that the hub platform allows the choice without a tooling change, so a wheel brand can develop two variants of the same model — one tuned for stiffness, one tuned for a more even tension profile — around a single hub set. The spoke count of 20H front and 21H rear should be read together with the intended lacing pattern, since the two determine the final spoke lengths and the tension targets in the build sheet.

Freehub, Axle and Bearing Compatibility Check

Before a sample is ordered, the drive-side specification needs to be matched against the frame, groupset and price tier of the intended wheelset. The MT-116F/R supports Shimano HG, Road Micro Spline, SRAM XDR, Campagnolo N3W and Campagnolo 11/12-speed freehub standards. That spread covers the main road drivetrain families, but the correct freehub must be named explicitly on the purchase specification — a hub set that supports five standards still ships with one of them.

Axle spacing is fixed at 12×100mm front and 12×142mm rear thru-axle. Frames using quick-release or other thru-axle dimensions are outside this configuration, so the frame standard should be confirmed before anything else. The Center Lock disc interface is the other fixed point; rotor mounting follows from it.

Bearings are a specification choice rather than a single build: S&S steel, ENDURO and CeramicSpeed options are available. The right selection depends on the wheel's price position and the riding conditions it is sold into. A ceramic bearing option belongs on a premium build where the buyer expects it; a steel bearing suits volume programs where serviceability and cost control matter more. None of these options should be presented to end customers with performance claims that have not been verified for the specific build.

A practical pre-order checklist:

  1. Confirm frame thru-axle dimensions match 12×100mm / 12×142mm.
  2. Name the freehub standard required by the groupset, including speed count.
  3. Confirm the carbon spoke width (3.3mm or 5.2mm) against the T-head hole specification.
  4. Agree the lacing pattern and spoke count so spoke lengths can be calculated.
  5. Select the bearing option against the target retail tier.

Sampling and OEM/ODM Evaluation

A hub set at this weight and specification level is best judged in a built wheel, not on a spec sheet. A sample evaluation should confirm that the T-head spoke holes accept the intended carbon spokes without play or forced insertion, that the chosen lacing pattern reaches the target spoke tension, and that the freehub and axle combination fits the actual frame and groupset the wheel is designed for. Engagement feel with the selected ratchet should be assessed by the riders the wheel is intended for, since 36T and 54T will read differently to a criterium rider and an endurance rider.

ARC's role in this process is as an OEM/ODM hub manufacturer. Founded in 2013 and based in Taicang, Jiangsu, the company develops and manufactures hubs for bicycle brands, wheel manufacturers and distributors, with CNC machining and quality control supporting custom programs. For a wheel brand building a carbon-spoke road disc wheelset, that means the MT-116F/R can be specified as a platform — ratchet count, spoke interface, lacing pattern, freehub standard and bearing option — rather than accepted as a fixed catalogue item. Buyers developing a custom hub program should raise their configuration requirements at the sampling stage, when the specification can still be matched to the build.

The MT-116F/R is a strong candidate for road disc carbon wheel programs that need a light hub set with a genuine engagement choice and a carbon-spoke interface that covers both common spoke widths. Starting with 36T covers most road builds; moving to 54T is a deliberate decision for faster pickup. Either way, the value of the platform shows up when the ratchet, spoke interface, freehub and bearing choices are treated as one specification and confirmed in a sample wheel against the frame, groupset and tension targets the program actually requires.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China