Road Wheel Builds

ARC MT-116F/R Carbon Spoke Hub Set: 1:1 vs 2:1 Interface for Road Wheel Builds

15 min read
On this page 5 sections

When a road disc carbon wheelset is being specified around carbon spokes, the hub is no longer just a rotating part—it sets the lacing options, tension balance and the interface every spoke must match. The ARC MT-116F/R Center Lock road hub set is built around that decision: one platform with a carbon-spoke interface that supports both 1:1 and 2:1 spoke configurations, so a builder can choose the layout that fits the wheel's stiffness and tension plan rather than having a single layout fixed by the hub.

What the 1:1 and 2:1 Spoke Interfaces Change in a Build

The interface describes how drive-side and non-drive-side spokes are divided between the two flanges. A 1:1 layout assigns an equal number of spokes to each side; a 2:1 layout assigns roughly twice as many spokes to one flange as the other, which shifts how drive torque and braking load are distributed. On a rear disc hub the choice affects where the builder wants the extra spokes—typically toward the drive side, where torque transfer and spoke tension tend to be more demanding.

Because the MT-116F/R supports both configurations on the same hub set, the practical question at the planning stage is not which hub to buy but which lacing pattern the rim, spoke count and intended ride feel call for. A 1:1 plan is often easier to keep symmetrical in appearance and tension from side to side; a 2:1 plan can let the builder work with a higher spoke count on one flange to manage tension differential, but it also demands that the rim's drilling and the spoke lengths be confirmed for that specific pattern. The hub's role is to give both options without changing model—so specification should follow the wheel design, not the other way around.

It helps to treat the interface as a planning input rather than a marketing choice. Before committing, a builder should map the intended spoke count, note which flange carries the extra spokes in a 2:1 plan, and check that the rim's spoke holes are drilled for that pattern. If a design is already locked to a rim with a fixed drilling, the 1:1 and 2:1 options should be matched to it rather than assumed interchangeable.

Confirming Spoke, Axle and Freehub Compatibility Before Lacing

The most common build failure at this stage is a spoke that does not sit correctly in the hub. The MT-116F/R uses dedicated T-head spoke holes designed to accommodate compatible 3.3mm and 5.2mm wide carbon spokes, so the first check is whether the intended carbon spoke's head width falls within that range. A spoke that is dimensionally compatible still needs its length and head seating verified against the specific flange, especially in a 2:1 layout where the two flanges are not loaded identically.

Axle and frame fit come next. The hub set is built around 12×100mm front and 12×142mm rear thru-axle spacing, the common road disc standard, so it should be confirmed against the frame and fork specification rather than assumed. The Center Lock disc interface then determines rotor mounting and should match the rotor's lockring system. These are binary checks—either the frame, rotor and axle match or they do not—and they should be cleared before any lacing diagram is drawn.

Freehub choice is the other decision that must be fixed early, because it determines the cassette and thus the drivetrain the wheel is built for. The MT-116F/R supports Shimano HG, Road Micro Spline, SRAM XDR, Campagnolo N3W and Campagnolo 11/12-speed freehub standards. A builder specifying for a SRAM AXS road groupset, for example, needs the XDR freehub confirmed at order, not after the wheel is built. Each of these points is a specification to verify with ARC before sampling, and the product detail page is the reference for the configuration set rather than a substitute for confirming the exact combination on the order.

Ratchet, Bearing and Weight Decisions at Order Stage

Engagement and bearing choice are often left too late, but they are easier to settle while the hub is still being specified. The MT-116F/R uses a patented one-piece ratchet architecture available in 36T and 54T options. The trade-off is the familiar one: a higher tooth count gives quicker engagement and is often preferred for technical or punchy riding, while a lower count changes the engagement feel and is a legitimate choice for riders who do not need the fastest pickup. Neither is inherently better—the point is to match the ratchet to the intended use and to confirm the choice at order.

Bearing options are S&S steel, ENDURO and CeramicSpeed. These are different bearing specifications, and the selection should reflect the wheel program's target—whether the priority is a straightforward steel build or a higher-specification bearing for a premium wheelset. Bearing choice is an order-stage decision, so it belongs in the same conversation as the freehub and axle confirmation.

Weight is best treated as a reference rather than a promise. The complete hub set is quoted at approximately 281.1g, a figure that helps a builder position the wheelset in a lightweight road disc build. It should be read alongside the shell and axle materials—a precision-forged AL6061-T6 aluminum hub shell with AL7075 axles, freehub body and end caps—rather than as a standalone target, since final wheel weight depends on rim, spokes, nipples and build. Actual weight of a delivered set should be confirmed with ARC if it is critical to a published specification.

Working with ARC on a Carbon Road Disc Wheel Program

For wheel builders, wheelset brands and OEM product managers, the MT-116F/R is most useful when it is treated as a configurable platform rather than a catalogue item. The combination of a dual 1:1/2:1 carbon-spoke interface, Center Lock, 12×100/12×142 thru-axle spacing and multiple freehub and bearing options means one hub family can serve several wheel programs—but only if each program's spoke, axle, freehub and ratchet choices are confirmed before sampling.

That is where ARC's position as a hub manufacturer matters. Founded in 2013 and based in Taicang, Jiangsu, ARC specializes in the development, manufacturing and customization of high-performance bicycle hubs and provides OEM and ODM solutions for global bicycle brands, wheel manufacturers and distributors. For a carbon road disc wheel program, that means the MT-116F/R can be discussed as a customization starting point: the interface, freehub standard, ratchet tooth count and bearing specification are the variables to align with the wheel design, and the sample stage is the right place to confirm them.

A sensible next step is to bring a specific build to ARC rather than a general request: the intended spoke count and lacing pattern, the carbon spoke width, the frame's thru-axle standard, the drivetrain's freehub requirement, and the target ratchet and bearing specification. With those fixed, the MT-116F/R can be evaluated as a concrete hub choice for that wheelset, and the sample can be checked against the lacing and tension plan before production planning moves forward.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China