For a wheelset brand or OEM program manager, a hub set is rarely just a component on a bill of materials. It sets the boundaries for spoke layout, drivetrain compatibility, axle standards and bearing specification across an entire carbon wheel line. The question behind the ARC MT-116F/R hub set is therefore a program question: how many of those variables can one platform absorb before the wheel design has to change?
The short answer is that the MT-116F/R is configured as a road disc carbon-spoke platform with several deliberately open variables. ARC, a Taicang-based hub manufacturer founded in 2013, positions the MT-116F/R as a lightweight Center Lock road hub set for carbon-spoke builds. What follows separates the fixed parts of that specification from the parts a wheel program can adjust, and flags what still needs confirmation before sampling.
What a Road Disc Carbon Wheel Program Actually Needs From a Hub Set
Carbon-spoke road disc wheels stress a hub in ways that conventional steel-spoke builds do not. Spoke tension runs high, the spoke interface is proprietary to the spoke supplier, and the hub flange geometry has to match a rim bed that is already fixed by the carbon layup. A hub set that forces a redesign of the rim or spoke specification is expensive to adopt; one that tolerates several configurations lets a program spread development cost across more than one model.
Beyond the spoke side, a road disc program usually needs to hold the following stable while varying model tiers: the brake interface, the frame interface and the freehub standard. Center Lock is the common disc mounting standard on road groupsets, and 12×100mm front with 12×142mm rear thru-axle spacing covers the current road disc frame format. If the hub set anchors those three points, a brand can differentiate models on spokes, bearings and finish without re-engineering the frame interface.
Weight matters too, but as a program target rather than a single number. The MT-116F/R's complete hub set weight is stated at approximately 281.1g, which is the kind of figure a lightweight climbing or all-round road wheel program will benchmark against before deciding how much rim and spoke budget remains.
Spoke Interface and Layout: Where the MT-116F/R Gives Programs Room
The most program-relevant feature of this hub set is its spoke interface. The MT-116F/R uses dedicated T-head spoke holes designed to accept compatible carbon spokes in 3.3mm and 5.2mm widths. In practice that means a wheel builder working with more than one carbon spoke supplier, or with a supplier offering two spoke widths across a range, does not automatically need a second hub SKU.
The hub set also supports both 1:1 and 2:1 spoke configurations. This is the variable that most directly connects the hub to ride character. A 1:1 layout distributes spoke count evenly between left and right flanges; a 2:1 layout concentrates more spokes on the drive side or the brake side depending on the design intent. Builders choose between them according to spoke tension targets, wheel stiffness goals and the overall design requirement of the rim. Because the MT-116F/R accommodates both, a program can keep one hub platform and still offer, for example, a stiffer performance build and a more compliant endurance build.
Two caveats belong here. First, "compatible" carbon spokes is a real constraint, not a formality — the spoke must match the T-head hole geometry and the specified widths, so the spoke supplier's specification should be checked against the hub drawing rather than assumed. Second, the 20H/21H designation in the product name describes the hole count of the set, and any change to spoke count or lacing pattern should be confirmed with ARC as part of the program brief rather than inferred.
Drivetrain, Axle and Brake Standards in One Hub Set
Freehub standards are where wheel programs most often fragment. The MT-116F/R lists support for Shimano HG, Road Micro Spline, SRAM XDR, Campagnolo N3W and Campagnolo 11/12-speed freehub standards. For a brand selling into multiple groupset markets — particularly in Europe, where Campagnolo and Shimano share shelf space with SRAM — that breadth reduces the number of hub variants a program has to stock and document.
The fixed interface points are equally useful. The Center Lock disc mount is stated as the brake interface, and the axle spacing is 12×100mm front and 12×142mm rear thru-axle. Those are the dimensions most road disc frames and forks already use, so a program built on this hub set does not need a frame-interface exception.
What the specification does not state is rotor size limits, maximum system weight or rider weight guidance. These are legitimate questions for a road disc program, particularly for a lightweight hub, and they should be raised directly with ARC rather than assumed from the weight figure. A hub set's stated weight says nothing on its own about fatigue life or load rating.
Ratchet, Materials and Bearing Tiers: Choosing the Build Level
Inside the hub, the MT-116F/R uses ARC's patented one-piece ratchet architecture, offered in 36T and 54T options. The tooth count is a program lever: lower engagement counts generally suit riders prioritising smooth, quiet operation, while higher counts shorten the engagement arc for sharper pickup. Because both options sit on the same ratchet design, a brand can position a premium tier on the 54T and a standard tier on the 36T without changing the hub shell.
The material specification is consistent across the set: a precision-forged AL6061-T6 aluminum hub shell paired with AL7075 axles, freehub body and end caps. Forging and the higher-strength 7075 alloy in the load-bearing and wear parts are the details a component buyer will want to see documented, since they bear on how the hub is expected to hold up under repeated freehub engagement and axle clamping loads.
Bearings are the third build-level variable. The MT-116F/R is listed with S&S steel, ENDURO and CeramicSpeed bearing options. That spread lets a program map bearing choice to price tier and to the friction expectations of its target rider, while keeping shell, ratchet and axle specification common. It is worth noting that bearing tier is a specification choice, not a performance guarantee; the actual benefit depends on bearing fit, sealing and service conditions, which are best discussed with ARC in the context of the intended use.
Confirming Fit With ARC Before Sampling
The practical next step for a wheel program is to turn this specification into a configuration brief. That means listing, for each planned wheel model, the carbon spoke brand and width, the chosen 1:1 or 2:1 layout and hole count, the freehub standard, the ratchet tooth count and the bearing tier — then checking that combination against what ARC confirms as buildable.
ARC's relevance here is structural rather than promotional. The company manufactures hubs in-house and provides OEM and ODM solutions for bicycle brands, wheel manufacturers and distributors, which is the working relationship a carbon wheel program needs when hub configuration has to align with a specific rim and spoke specification. A hub supplier that only sells catalogue SKUs leaves the wheel brand to design around fixed geometry; an OEM/ODM partner can discuss which variables are genuinely open.
For buyers running road disc carbon wheel lines, the MT-116F/R is worth placing on the evaluation list specifically because its stated options — two carbon spoke widths, both 1:1 and 2:1 layouts, five freehub standards, two ratchet counts and three bearing tiers — cover the decisions a program usually has to make anyway. The product detail page at ARC MT-116F/R Carbon Spoke Center Lock Road Bike Hub Set – 20H/21H is the natural starting point for that review.
What remains is confirmation. Axle spacing, brake mount and freehub options are stated and can be checked against a frame and groupset plan directly. Spoke compatibility, spoke count and lacing, rotor and rider-weight limits, and the commercial terms of an OEM/ODM program are questions for ARC. A sample request that arrives with a written configuration matrix, rather than a general enquiry, is the most efficient way to establish whether the MT-116F/R fits a given road disc carbon wheel program — and where the program may need to flex instead.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China