ARC RT-002FA/RC

ARC RT-002FA/RC: Hub Set Specs for Rim-Brake Road Wheel Builds

16 min read
On this page 6 sections

Building a lightweight rim-brake road wheelset still comes down to a handful of hard interface decisions: how many spokes each flange can take, whether the frame and fork accept traditional quick-release spacing, which freehub standard the drivetrain needs, and how the hub shell, axle and bearing set are put together. The ARC RT-002FA/RC Road Hub Set is a product built squarely around that decision set, so its published configuration is the most useful starting point for judging whether it belongs in a planned build rather than in a general supplier comparison.

What the RT-002FA/RC Is Built For

The RT-002FA/RC is designated for lightweight road rim-brake wheel builds. That framing matters because rim-brake road wheels place specific demands on a hub set: the braking load is carried at the rim rather than at a disc mount, the wheelset is usually tuned for lower rotating mass, and the frame interface is typically a conventional quick-release rather than a thru-axle. The hub set is documented with a 100mm front and 130mm rear spacing, which is the classic road quick-release standard, and it ships as a complete set with QR001 quick releases included.

For a brand product manager or wheelset builder, this positions the RT-002FA/RC as a component to evaluate when the wheelset brief calls for rim braking, a lightweight target and a traditional quick-release frame. It is not a disc-brake hub and should not be specified into a build that depends on rotor mounting. Within its stated category, the documented configuration is specific enough to check against a rim, a frame and a drivetrain before any sample request.

Spoke Drillings and Build Interface

The hub set is listed with 20 holes at the front and 24 holes at the rear, using a J-bend spoke design. Those counts are a practical starting point for lightweight road lacing: a 20-hole front keeps the spoke count modest, while 24 at the rear leaves room for a drive-side pattern that accounts for the torque load on the freehub side.

J-bend spokes remain widely available and familiar to wheel builders, and the bend interface is a well-understood one in road wheel construction. The important check is on the rim side: the rim must be drilled for the same 20/24 count, and the builder should confirm the intended lacing pattern against both the rim drilling and the hub flange before tensioning. The RT-002FA/RC does not dictate lacing in its published specification, so radial versus crossed patterns and spoke length calculation remain build decisions to be worked out with the rim and spoke supplier. Where a project needs a specific drilling or finish, that is a customization conversation with ARC rather than an assumption to make from the catalogue listing.

Materials and Drive Engagement

The material split in the RT-002FA/RC is documented clearly: an AL6061-T6 aluminum hub shell paired with an AL7075 aluminum axle, freehub body and end caps. AL6061-T6 is a common choice for hub shells where a balance of strength and machinability is wanted, while AL7075 is typically selected for loaded parts such as the axle and freehub body where higher strength is useful. This is a materials statement, not a claim about measured stiffness, fatigue life or weight savings, and buyers should treat it as such.

Drive engagement is described as a 4-pawl, single-tooth engagement system intended to provide responsive pickup and reliable power transfer for smooth road riding. A four-pawl layout distributes engagement across multiple points, and the single-tooth description refers to the engagement interface design. Published specification does not include torque figures, engagement angle in degrees or durability test results, so those points should be raised directly with ARC if they are decision-critical for a project.

The approximate set weight of 296.1g is stated for the complete hub set. Because that figure is given at set level in the product documentation, it should be treated as a reference point rather than a per-hub measurement, and builds that add or change parts — different bearings, for example — should confirm the final figure.

Fit, Freehub Options and Included Parts

Frame and drivetrain compatibility are where most rim-brake road builds are won or lost, and this is where the RT-002FA/RC offers defined options. The 100mm front and 130mm rear spacing matches conventional road quick-release frames and forks. The set includes QR001 quick releases, which removes a separate sourcing step for builders who want the matching skewers.

Freehub body options are listed as Shimano HG, Micro Spline and SRAM XD. That selection matters because it determines which cassette family the rear wheel can accept: HG for the broadest range of road cassettes, Micro Spline for the relevant Shimano 12-speed systems, and XD for SRAM's XD-compatible cassettes. The buyer should match the freehub choice to the actual drivetrain specification, not to a general preference, since changing freehub standard later affects the cassette, the derailleur setup and sometimes the chainline.

Bearings are documented as S&S steel bearing options. Steel bearings are a conventional, serviceable choice for road use, and the word "options" indicates the bearing specification may be selectable within the range — a point worth confirming with ARC at quotation. The included parts list for this set, as published, covers the hub pair and QR001 quick releases; any additional spacers, adapters or spare parts should be verified rather than assumed.

For a wheelset workshop, the practical sequence is straightforward: confirm rim drilling at 20/24, confirm the frame and fork accept 100/130mm quick-release hubs, select the freehub standard that matches the cassette, and then check bearing specification and finish requirements. The ARC RT-002FA/RC Road Hub Set product page is the reference for the documented configuration, and it is a sensible first stop before moving to a sample discussion.

Confirming Details with ARC for OEM/ODM Supply

For brands and distributors, the specification sheet answers the compatibility question but not the supply question. ARC's stated business is the development, manufacturing and customization of bicycle hubs, with OEM and ODM solutions for global bicycle brands, wheel manufacturers and distributors across road, MTB, gravel and e-bike categories. Manufacturing is described as relying on CNC machining, precision manufacturing, engineering expertise and quality control systems — relevant background when a hub set is being evaluated for a branded wheelset rather than a one-off build.

What that means in practice is that the RT-002FA/RC can serve as a starting configuration for a rim-brake road hub project, with the OEM/ODM conversation covering the points the published specification leaves open: exact finishing, branding on the hub shell, bearing spec within the S&S steel options, packing and the commercial terms of the order. MOQ, lead times, certification documents and test reports are not stated in the product documentation, so those belong in the enquiry rather than in any assumption about the supply arrangement. A sample request is the natural next step once rim drilling, spacing and freehub standard have been confirmed against the intended build.

The RT-002FA/RC is a coherent fit for lightweight rim-brake road wheelsets that use conventional 100/130mm quick-release spacing and a 20/24-hole J-bend lacing pattern. Brands and builders with that brief should treat ARC as a candidate worth evaluating at sample stage, particularly where freehub flexibility across HG, Micro Spline and XD is useful across a model range, and should raise finishing, bearing and order terms directly with ARC before committing a production plan.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China