ARC RT-002FA/RC Road

ARC RT-002FA/RC Road Hub Set: What Road Wheel Builders Should Know

14 min read
On this page 6 sections

What the RT-002FA/RC Hub Set Is Built For

Road wheel builders working on rim-brake wheelsets face a narrowing supply picture. Rim-brake road frames remain in service across Europe, and rebuilders and small-series brands still need hubs that match 100 mm front and 130 mm rear dropouts, accept conventional J-bend spokes, and can be drilled for lacing patterns that suit lightweight rims. The ARC RT-002FA/RC Road Hub Set sits directly in that space: ARC lists it as a hub set designed for lightweight road rim-brake wheel builds.

That description matters because it sets the boundary of the product's intended use. This is not a disc-brake hub and not an all-road or gravel component. It is a rim-brake road hub set, and the specification should be read against the demands of that category: low rotating mass, a reliable ratchet mechanism for steady road pedaling, and a shell geometry that keeps flange spacing consistent with conventional road lacing. ARC, a hub manufacturer based in Taicang, Jiangsu, founded in 2013, offers OEM and ODM solutions for wheel manufacturers and distributors, and the RT-002FA/RC is one of the road-specific products in that range.

Materials and Spoke Interface in Practice

The construction choices in this hub set are conventional in the best sense, which is useful for builders who want predictable assembly behavior rather than unfamiliar interfaces. The hub shell is machined from AL6061-T6 aluminum, a widely used, weldable and machinable alloy with good corrosion resistance and moderate strength. The axle, freehub body and end caps are specified in AL7075 aluminum, a higher-strength alloy that allows thinner walls in load-bearing parts, which is relevant where axle stiffness and freehub durability matter at low weight.

The spoke interface is J-bend, not straight-pull. For wheel builders this is a meaningful decision point: J-bend spokes are available in broad lengths and profiles from many suppliers, are familiar to most builders, and allow lacing changes without dedicated straight-pull tooling. A builder planning a lightweight road wheel with a conventional 20/24-hole drilling can therefore work with standard spoke stock and existing truing practice. The trade-off is that J-bend hubs require careful elbow seating and consistent tensioning to avoid spoke fatigue at the bend, so build quality remains a factor that no hub specification can substitute for.

Drilling, Spacing and Drivetrain Options

The RT-002FA/RC is offered with 20-hole front and 24-hole rear drilling. That combination suits low-spoke-count road builds where aerodynamic rims and lightweight rimsets are paired with fewer spokes, and it constrains the lacing plans available: a 20-hole front typically calls for a two-cross or radial pattern depending on the rim manufacturer's guidance, while the 24-hole rear allows three-cross or mixed patterns. Builders should confirm the rim maker's spoke-count and lacing recommendations before committing, since hub flange geometry and rim drilling must agree.

Spacing is 100 mm front and 130 mm rear, the standard for rim-brake road frames and the reason this hub set is not interchangeable with disc-brake platforms. Freehub options include Shimano HG, Micro Spline and SRAM XD. That range covers the common road drivetrain families, but builders should match the freehub choice to the cassette standard their customers actually use rather than treating the three options as universally equivalent; Micro Spline and XD cassettes have different spline profiles and mounting procedures from HG. The set ships with QR001 quick releases, which suits quick-release rim-brake frames.

Engagement, Bearings and Weight: What to Verify

ARC states a 4-pawl, single-tooth engagement system intended to provide responsive pickup and reliable power transfer. For road use, this design is relevant to the feel of pedaling under load, particularly when accelerating out of slow corners or applying torque on climbs. What the specification does not establish is a quantified engagement angle, durability figure or drag measurement. Those are properties a builder should confirm through sample testing rather than inferring from the pawl count.

The same caution applies to bearings and weight. ARC specifies S&S steel bearing options and a complete hub set weight of approximately 296.1 g. Bearing grade, preload adjustment and seal design affect rolling resistance and service life, and a stated bearing brand or option should be verified against the actual production specification. Weight should be confirmed on a sample set, since scale variation and included small parts can shift the figure. Builders evaluating this hub for a lightweight program should test spoke tension retention, freehub engagement consistency and bearing smoothness under load before approving a production run.

Working With ARC as a Hub Manufacturing Partner

For wheel brands and distributors deciding whether to open a discussion, the relevant question is whether ARC's manufacturing scope matches the program. ARC's stated capabilities include CNC machining, precision manufacturing and quality control systems, and the company describes its OEM and ODM work as serving bicycle brands, wheel manufacturers and distributors across road, MTB, gravel and e-bike categories. The RT-002FA/RC, with its defined materials, drilling, spacing and freehub options, is a concrete starting point for a rim-brake road wheel program rather than a generic supplier claim.

A practical next step is to request samples of the RT-002FA/RC configured to the intended freehub standard, build them into test wheels, and evaluate engagement, bearing feel and weight against the program's targets. Builders with specific requirements on flange geometry, spoke drilling or bearing specification can raise those points directly in an OEM or ODM conversation, since customization is part of ARC's stated service scope. Where the specification is silent, such as exact engagement angle or bearing service interval, the appropriate response is to ask rather than assume. For road wheel builders still supplying rim-brake wheelsets, the ARC RT-002FA/RC is a hub set worth including in the evaluation list, provided the build plan and drivetrain standard are confirmed first.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China