RT-002FB/002RB Road Hub

ARC RT-002FB/002RB Road Hub Set: Rim-Brake Wheel Configurations Explained

16 min read
On this page 6 sections

Wheel builders and product managers working on rim-brake road wheelsets usually reach a decision point quickly: does a given hub set actually fit the drilling, spacing, and freehub requirements of the build, or will it force a redesign of the spoke plan? The ARC RT-002FB/002RB Road Hub Set answers that question with a fairly narrow but clear specification—two spoke drillings, 100 mm front and 130 mm rear spacing, J-bend spokes, and a choice of three freehub standards—aimed at lightweight road rim-brake wheel builds.

What "Rim-Brake Road Wheel Configuration" Means for This Hub Set

For a rim-brake road wheel, the hub has to satisfy a different set of constraints than a disc-brake hub. There is no rotor mount to account for, so the flange geometry, shell width, and spoke interface can be optimized around rim-brake caliper clearance and traditional road frame spacing. The RT-002FB/002RB is built specifically for this category: it is a rim-brake road hub set rather than a platform adapted from a disc-brake design.

In practical terms, a "configuration" here covers four variables that must line up before a wheelset can be specified: the spoke drilling (how many holes in the front and rear hub), the over-locknut distance (O.L.D.) at each end, the spoke type the hub accepts, and the freehub standard. Get any one of these wrong and the build stalls at the truing stand or at the cassette. The RT-002FB/002RB defines each of these variables explicitly, which is what makes it usable as a specification item rather than a generic hub.

Spoke Drilling Options: 18H/21H and 20H/24H

The hub set is available in two drilling pairs: 18H front / 21H rear and 20H front / 24H rear. These are not interchangeable interpretations of the same hub—they are distinct SKUs, and the choice between them shapes the entire wheel build.

The 18H/21H option suits builders pursuing a lower spoke count, typically paired with a shallow-to-mid-depth rim where weight and a clean aesthetic matter more than maximum spoke redundancy. It is a common direction for lightweight rim-brake road wheels where the rim itself carries much of the stiffness requirement.

The 20H/24H option gives four more spoke positions at each end, which is the more conservative choice for riders or programs that want a wider margin on spoke tension distribution and fatigue life, or for rims that call for a higher count in their own specification. Because the rear hub carries drive torque and the dish of a rim-brake rear wheel, the 21H versus 24H difference is the more consequential of the two pairings.

Neither drilling is "better" in isolation. The right question is which one matches the rim manufacturer's recommended spoke count and the intended rider load. A builder specifying a lightweight climbing wheelset and a program specifying an all-round road wheelset may reasonably land on different answers from the same hub family.

Spacing, Spoke Type, and Freehub Compatibility

The O.L.D. is 100 mm at the front and 130 mm at the rear—the traditional quick-release road standard. This is the spacing that rim-brake road frames and forks are built around, and it is the reason this hub set belongs in rim-brake programs rather than being pressed into disc-brake frames with 12 mm thru-axles or 142 mm rear spacing. Buyers should treat 100/130 mm as a hard fit condition, not a preference.

The hub accepts J-bend spokes. That matters at the procurement stage because J-bend and straight-pull spokes are not interchangeable at the hub flange, and spoke inventory, lacing patterns, and build fixtures all follow from this choice. J-bend remains widely stocked and well understood by custom builders, which keeps replacement and service simple for the end customer.

Freehub compatibility covers three standards: Shimano HG, Micro Spline, and SRAM XD. This is a meaningful range for a road hub, since it lets one hub platform serve drivetrains built around an HG cassette body, a Micro Spline body, or an XD driver. For a wheel brand selling into multiple drivetrain ecosystems, specifying the freehub at the order stage avoids stocking three separate hub part numbers. The freehub standard should be locked down together with the drilling, because both are fixed at the point of manufacture rather than swapped later.

Materials, Engagement, and Weight in the Build

The shell is AL6061-T6 aluminum, while the axle, freehub body, and end caps are machined from high-strength AL7075 aluminum. That split is a sensible one for a lightweight road hub: the shell is a structural housing where 6061-T6 offers good machinability and toughness, while 7075 in the axle and freehub addresses the higher-stress, thinner-walled parts. Bearings are S&S steel.

Drive engagement comes from a 4-pawl, single-tooth system with 48-point engagement. In ride terms, a higher points-of-engagement count reduces the rotation before the pawls pick up, which is felt as quicker response when power is reapplied. It is worth being precise here: engagement point count describes the drive mechanism, not a claim about durability or drag, both of which depend on the full build, bearing condition, and service.

Total weight is approximately 262.3 g for the set, and QR001 quick releases are included. For a rim-brake road wheelset where the rim and tire often dominate the weight budget, a hub set in this range leaves room for a competitive complete wheel without forcing a lightweight rim choice that compromises stiffness.

Confirming the Right Configuration Before Ordering

The specification is clear enough that most of the pre-order work is matching it to the wheel program rather than interrogating the hub itself. Before placing an order, buyers should confirm the following with ARC:

  • Spoke drilling: 18H/21H or 20H/24H, checked against the rim's recommended count and the intended rider load.
  • Freehub standard: Shimano HG, Micro Spline, or SRAM XD, matched to the drivetrain the finished wheel will carry.
  • Spacing: confirm the frame and fork are 100 mm front / 130 mm rear quick-release, since this hub set is not intended for thru-axle or disc-brake frames.
  • Spoke type: J-bend, with the spoke inventory and lacing plan prepared accordingly.
  • Quick release: QR001 is included, but confirm whether the program requires a specific skewer or aftermarket option.
  • OEM/ODM requirements: if the hub is being adapted into a branded wheelset, raise customization, branding, packaging, and volume expectations early so they can be assessed against ARC's manufacturing scope.

ARC, operated by Taicang Xiangyue Sports Equipment Co., Ltd., manufactures this hub set as part of a road, MTB, gravel, and e-bike hub range, and provides OEM and ODM solutions for bicycle brands, wheel manufacturers, and distributors. For a rim-brake road wheel program, the RT-002FB/002RB is worth placing on the shortlist when the build calls for 100/130 mm spacing, J-bend spokes, and a choice of HG, Micro Spline, or XD freehubs—and the two drilling options mean the same hub family can serve both a lightweight climbing wheelset and a more conservatively spoked all-round model. The productive next step is to fix the drilling and freehub against the rim and drivetrain specification, then confirm those choices, along with any OEM/ODM customization, directly with ARC before the order is released.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China