Rim-brake road wheelsets are now a specialist segment, but they are far from obsolete. Wheel builders still supplying lightweight climbing wheels, classic steel and titanium frames, and rim-brake training wheels need hubs that match narrow dropout spacing, accept quick releases and keep weight low without sacrificing durability. The ARC RT-030FCB/RCB 20/24H carbon straight-pull hub set from ARC is aimed squarely at that brief, and its specification sheet repays close reading before anyone commits to a sample order.
What This Hub Set Is Built For
The RT-030FCB/RCB is a road hub set designed around rim-brake wheels, not a disc-brake platform adapted backwards. That distinction matters because it determines the axle standard, the frame interface and the way the flanges can be shaped. The set uses 100mm front and 130mm rear spacing, which is the conventional quick-release road standard still found on rim-brake frames and forks. Both hubs are drilled for straight-pull spokes, with 20 holes at the front and 24 at the rear.
The stated design intent is a lightweight rim-brake road wheel, and the headline figure is a total set weight of approximately 290.1g. For builders working on climbing wheels or all-round road wheels where rim brake hardware already saves grams at the rim, a hub set in this range keeps rotating mass concentrated near the centre. The RT-030FCB/RCB should be read as a dedicated rim-brake component rather than a universal hub that happens to fit caliper frames.
Shell, Axle and Freehub Materials
The material split is the most useful thing to understand about this hub set, because not every "carbon" hub uses carbon in the same places. ARC specifies an AL6061-T6 aluminium and carbon-tube hub shell. In other words, the shell combines a carbon tube with aluminium structural elements rather than being a fully moulded carbon body. Buyers should confirm with ARC which portions of the flange and barrel are carbon and which are aluminium, since that affects how the hub takes spoke tension and how it should be inspected on arrival.
The load-bearing parts are described differently. The axle, freehub body and end caps are made from high-strength AL7075 aluminium. This is a sensible division of labour: AL7075 is a high-strength alloy commonly chosen for axles and freehub bodies where wear resistance and stiffness matter, while the shell construction is where weight can be trimmed. A wheel builder evaluating this set should treat the shell as a composite assembly and the axle and freehub as machined aluminium components, then check tolerance and bearing fit at both ends during sample inspection.
ARC's own manufacturing background supports this kind of assembly. The company states that it uses advanced CNC machining, precision manufacturing and strict quality control systems, and it produces hubs across road, MTB, gravel and e-bike categories with OEM and ODM customisation for brands, wheel manufacturers and distributors. That breadth is relevant here mainly as context for how the RT-030FCB/RCB is produced, not as a claim about this specific hub's test results.
Engagement and Spoke Layout
The drive system uses six pawls with single-tooth engagement and 72 points of engagement. In practical terms, more engagement points reduce the crank rotation needed before drive is picked up, which riders notice when accelerating out of slow corners or climbing steep pitches. ARC describes the system as providing responsive pickup and consistent power transfer. That is a design description rather than a measured efficiency claim, and buyers should treat it as such: the number of pawls and engagement points tells you the mechanism, but actual durability depends on pawl and ratchet materials, lubrication and load history.
The spoke drilling is where this hub set becomes a genuinely specific product. The front hub uses a 20-hole 1:1 straight-pull layout, while the rear uses a 24-hole 2:1 straight-pull layout. A 2:1 rear pattern typically groups twice as many spokes on the drive side as the non-drive side, which helps balance tension when the dish of a rim-brake rear wheel pushes spoke angles apart. Builders should check that their chosen rim and spoke lengths are calculated for these exact counts and for straight-pull heads, because straight-pull hubs cannot be re-laced with J-bend spokes and spoke length errors are costly.
Straight-pull designs also change the build process. Spokes are inserted before the hub is laced into the rim, and the flange geometry fixes the lacing pattern to a large extent. Anyone shortlisting the RT-030FCB/RCB should confirm the intended cross pattern with ARC before ordering rims, especially on the 2:1 rear where drive-side and non-drive-side spoke lengths will differ.
Compatibility, Bearings and Weight
The freehub is offered in Shimano HG and SRAM XDR standards, which covers the great majority of rim-brake road drivetrains still in service, from 11-speed mechanical groupsets to modern electronic setups. Buyers should specify the freehub standard at order rather than assume a default, because HG and XDR are not interchangeable and the choice determines cassette compatibility.
The hub set uses S&S steel bearings, listed as a bearing option, and ships with QR019 quick releases included. Both are configuration points worth writing into the purchase order: bearing specification and quick release model should appear explicitly on the quotation so that a later production batch can be checked against the same reference. The approximate 290.1g set weight should likewise be tied to the exact configuration quoted, since freehub standard, bearing choice and quick releases all sit within that figure.
ARC's OEM and ODM model is relevant to how these variables are handled. Because the company customises hubs for wheel brands and distributors, options such as freehub standard and bearing specification are normally settled during the specification conversation rather than left to chance. For a rim-brake program, that means the buyer can define the build once and ask for the same configuration to be repeated across batches.
What to Confirm Before Sampling
A specification sheet answers what a hub is; a sample answers whether it suits your wheel. Before requesting samples of the ARC RT-030FCB/RCB, it is worth resolving a short list of points with ARC directly.
- Shell construction detail: ask which parts of the AL6061-T6 and carbon-tube shell are carbon and which are aluminium, and how the flanges are finished.
- Spoke interface: confirm the straight-pull hole geometry and recommended spoke type for both the 20H front 1:1 and 24H rear 2:1 layouts.
- Freehub and bearings: specify HG or XDR, and confirm the S&S steel bearing specification in writing.
- Quick releases and spacing: verify that QR019 quick releases are included in the quoted configuration and that 100mm/130mm spacing matches your frame and fork.
- Weight basis: ask what the approximately 290.1g figure includes, so it can be compared fairly with competing sets.
- Inspection data: request the dimensional and quality documentation ARC can provide for the sample batch, and check bearing fit, axle end play and freehub engagement feel on receipt.
For wheel builders and brand product managers still developing rim-brake road wheels, the RT-030FCB/RCB is a credible candidate to place on a sample shortlist. Its value lies in the combination of a carbon-tube shell, AL7075 load-bearing parts, a defined 20/24H straight-pull drilling pattern and dual HG/XDR compatibility at a set weight near 290g. ARC's role as a hub manufacturer with OEM and ODM capability across road and other categories makes it a sensible partner to open a specification discussion with, provided the configuration questions above are settled before the first sample is built into a wheel.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China