For a wheelset brand or OEM engineer working on a rim-brake road program, the hub is rarely the headline component, yet it quietly sets the limits for spoke choice, lacing, dish and long-term service. The ARC RT-035F/R 20/24H straight-pull rim-brake road hub set is a useful case to read against a build sheet, because its stated configuration is narrow enough to judge quickly: a straight-pull design, 20-hole front at 1:1 and 24-hole rear at 2:1, 100 mm front and 130 mm rear spacing, and an approximate 336.6 g set weight. This article walks through what that means for rim-brake road wheel builds and what a buyer should verify before requesting samples.
Who this hub set is specified for
The RT-035F/R is specified for lightweight road rim-brake wheel builds and carries a straight-pull spoke design. That framing matters more than it first appears. Rim-brake road frames and forks were designed around traditional hub spacing, so a builder working on a rim-brake project is often updating an existing platform rather than starting from a disc-brake blank sheet. The hub therefore has to be compatible with the frame interface, the quick-release retention the frame expects, and the rim and spoke combination the brand has already validated or intends to validate.
The intended buyer is not a generalist. It is a road wheelset brand or a complete-bike OEM that wants a hub set for a lightweight, rim-brake wheelset and needs a defined starting configuration rather than a custom geometry exercise. The front 20-hole and rear 24-hole counts point in that direction: they suit a build where weight and spoke economy are part of the design brief, but the rim still needs enough spoke support to hold tension and stay true.
ARC, based in Taicang, Jiangsu, manufactures bicycle hubs and supplies OEM and ODM solutions to bicycle brands, wheel manufacturers and distributors. For this particular product, the relevant question is not whether ARC can make hubs in general, but whether the RT-035F/R's stated configuration lines up with a specific rim-brake road build. That is a specification conversation, and it should start with the build sheet rather than the catalogue.
Reading the straight-pull design and 20/24H lacing
Straight-pull spokes change the practical sequence of wheel building. Instead of a J-bend that hooks through a flange hole, the spoke runs directly from the hub's anchoring point to the rim, which affects how the builder handles spoke length, lacing pattern and tensioning sequence. For a production wheelset program, the practical implication is that spoke length and hub geometry must be confirmed together before any build trial. A straight-pull hub is not a drop-in substitute for a J-bend hub on the same rim without rechecking those values.
The 20H front at 1:1 and 24H rear at 2:1 configuration is a deliberate distribution choice. A 1:1 front means the left and right flanges carry an equal number of spokes, which suits a symmetric front wheel where braking and steering loads are shared. The rear 2:1 layout shifts the spoke count toward the drive side, where torque and the dish created by the cassette place higher demands. ARC states that these spoke configurations help optimize spoke tension distribution and wheel balance. That is a design intent, not a measured guarantee for every rim: actual tension balance depends on the rim's drilling, its stiffness, the spoke gauge and the builder's tensioning method.
For the buyer, this means the 20/24H counts should be treated as fixed inputs to the rim specification rather than flexible ones. If a brand already has a 24H front or 28H rear rim in its range, the RT-035F/R is not the matching hub for that rim, and the build plan should either change the rim or change the hub. Where the counts do match, the straight-pull layout and the 2:1 rear give the builder a clear, repeatable pattern to document in the wheel specification.
Compatibility checklist: freehub, spacing and bearings
The concrete compatibility facts on the RT-035F/R are worth separating from the design commentary, because these are the items that decide whether a sample is worth ordering.
- Freehub standards: Shimano HG and SRAM XDR are stated as compatible. A brand should confirm which freehub body is supplied with the sample and whether the requested standard is available at the time of enquiry, since the two standards serve different drivetrain families.
- Spacing: 100 mm front and 130 mm rear, which is the conventional rim-brake road spacing. This should be checked against the actual frame and fork drawings, not assumed from the frame category.
- Bearings: S&S steel bearings are specified. Bearing grade, preload adjustment method and service interval are not stated in the product information and should be confirmed directly if they matter to the program.
- Quick releases: QR019 quick releases are included with the set, which is relevant for rim-brake frames that rely on quick-release retention rather than thru-axles.
- Rotor interface: none is required in a rim-brake build, but a buyer converting a frame design should confirm there is no expectation of a disc mount on the hub.
Weight is stated at approximately 336.6 g for the set. That figure should be treated as a reference for the set as specified, not a guarantee for every variation, because freehub body choice and small configuration differences can move the number. For a lightweight road program, it is a reasonable figure to enter into an initial build-weight estimate, with a confirmed sample weight to follow.
Materials, weight and engagement at a glance
The material stack is consistent with a road-oriented hub: an AL6061-T6 aluminum hub shell paired with a high-strength AL7075 aluminum axle, freehub body and end caps. Using a higher-strength aluminum for the axle and freehub body is a common way to keep mass down while retaining the stiffness the drivetrain loads require. The shell material is a familiar choice for hubs where machining consistency and corrosion behaviour matter.
Engagement is handled by a 4-pawl, single-tooth system, which ARC describes as providing reliable power transfer and consistent drivetrain engagement. In practice, pawl count and tooth engagement affect how quickly the drive engages and how the load is spread across the mechanism. The product information does not state a tooth count, engagement angle or spring specification, so a buyer should not infer a specific pick-up angle from the description. What can be said is that a four-pawl layout distributes drive load across multiple contact points, and the "single-tooth" description indicates the engagement geometry rather than a performance rating.
For a rim-brake road wheelset, these details sit behind the more visible choices of rim depth and spoke type, but they influence the riding feel and the service story. A wheelset brand evaluating the RT-035F/R should compare the stated materials and engagement against its own durability expectations and its service model, and ask ARC directly for the engagement specification if the program requires it.
What to confirm with ARC before sampling
The RT-035F/R is a defined product, and the fastest way to evaluate it is to send a build sheet rather than a general enquiry. Before requesting samples, a buyer should confirm the following points with ARC. First, the freehub standard required for the program and whether that body is supplied on the sample. Second, the exact spoke counts and lacing pattern to be used, so that spoke length and rim drilling are checked against the 20H front 1:1 and 24H rear 2:1 configuration. Third, the measured weight of the sample as configured, since the stated 336.6 g is approximate. Fourth, the bearing specification and any service guidance available. Fifth, the quick-release model included and whether it matches the frame's dropout requirements.
Because ARC provides OEM and ODM solutions for global bicycle brands, wheel manufacturers and distributors, the conversation can extend beyond a standard sample if the build requires a defined hub configuration. The company's development, manufacturing and customization work is the relevant background here, while the RT-035F/R's own stated specifications remain the basis for any technical claim. It is also worth checking the RT-035F/R product page for the current published specification before the enquiry, so that any discrepancy between the web listing and the sample is caught early.
For a rim-brake road wheelset program, the RT-035F/R is a sensible candidate to put on the sample list when the build calls for a lightweight straight-pull hub in 20H front and 24H rear, Shimano HG or SRAM XDR freehub compatibility, and 100/130 mm spacing. It is less suitable where the rim range already dictates different spoke counts or where a thru-axle interface is required. The next step is a specification confirmation covering freehub body, spoke counts, sample weight and included quick releases; with those answers in hand, a brand can judge whether the hub belongs in its build and move to a sample build with a clear set of parameters to validate.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China