What the freehub standard actually decides
When a product manager or wheelset builder starts specifying a Boost MTB hub set, the conversation often jumps straight to spacing, spoke count and weight. The freehub standard deserves to come first, because it is the one decision that cannot be changed after the order is placed without changing the cassette, the drivetrain and possibly the frame's chainline assumptions. The freehub body is the mechanical interface between the hub shell and the cassette. Its spline pattern, diameter and length determine which cassette physically mounts, how far outboard the largest cog sits, and how the chainline falls into place. Get it wrong and the wheel is either unusable or requires a new cassette and a rethought drivetrain.
This is why freehub compatibility is a specification decision rather than an accessory choice. A Boost hub set is ordered against a frame, an axle standard and a drivetrain plan. The freehub standard is the point where the drivetrain plan becomes a hard constraint on the hub order. Once a hub supplier has machined and assembled a batch around one freehub interface, switching to another means new freehub bodies, new assembly work and new lead times. Fixing the standard at the specification stage avoids that cost entirely.
HG, Micro Spline and XD: three interfaces, one build decision
The three freehub standards most often specified for mountain bikes differ in spline geometry and intended cassette families, and each carries its own consequences for the build.
Shimano HG is the long-established spline pattern with a relatively narrow, tall-toothed profile. It accepts HG-type cassettes, including many 8- to 11-speed MTB cassettes and some 12-speed variants. It is widely available and cost-effective, which keeps it relevant for entry and mid-range builds and for distributors who want broad cassette compatibility across a catalogue.
Shimano Micro Spline uses a finer, shallower spline designed around 12-speed MTB cassettes with a smaller minimum cog. Because the interface is specific to that cassette family, it should only be specified when the drivetrain plan is confirmed. It is not interchangeable with HG bodies.
SRAM XD uses a threaded, tapered interface that allows a 10-tooth smallest cog and is tied to SRAM's XD cassette family. Like Micro Spline, it locks the build into a particular cassette ecosystem.
The practical implication is that the freehub standard follows from the drivetrain, not the other way round. A brand planning one frame platform across several build tiers may need more than one freehub option in the same hub model; a distributor stocking replacement wheels needs to know which cassette families its customers actually run. Deciding this after the hub order is placed turns a straightforward specification into a rework problem.
Where Boost spacing and freehub choice meet
Boost spacing and freehub standard are separate decisions, and conflating them is a common source of ordering errors. Boost spacing defines the frame and axle context: 15×110mm at the front and 12×148mm at the rear. It sets hub flange positions, spoke angles and the chainline the frame was designed around. The freehub standard defines the cassette interface. A hub can be correctly Boost-spaced and still be unusable if the freehub body does not match the cassette.
Both must be fixed in the same specification document. It also helps to record the ratchet or engagement choice, spoke count and disc interface at the same time, because these interact with the wheel build rather than the drivetrain. A 28H, 32H or 36H drilling decision affects spoke availability and wheel stiffness targets; a 6-bolt disc interface must match the rotor the build will use. Treating the freehub standard as one line item among these, rather than an afterthought, keeps the hub order internally consistent.
ARC manufactures the MT-065F/R Boost MTB hub set with exactly this specification logic in mind: the model is offered with Shimano HG, Micro Spline and SRAM XD freehub compatibility alongside 15×110mm front and 12×148mm rear Boost spacing, so the freehub standard can be settled at the quotation stage rather than after tooling.
Specifying the MT-065F/R for a Boost build
The ARC MT-065F/R 32H Boost MTB Hub Set – 36T/54T Ratchet is a useful reference point for how these decisions come together. The hub set pairs an AL6061-T6 aluminum hub shell with an AL7075 aluminum axle, freehub body and end caps. Its ratchet system is available in 36T or 54T, using ARC's patented one-piece ratchet architecture, and the J-bend spoke design with 6-bolt disc interface supports 28H, 32H and 36H configurations. Bearings are S&S steel, and total weight is approximately 453.1g.
For a specification discussion, the important detail is that freehub compatibility and ratchet choice are both configurable on the same model. A trail or all-mountain build that has settled on a 12-speed Micro Spline drivetrain can specify that freehub and pair it with the engagement count that suits the terrain and rider cadence. A brand building a lower-tier variant on the same frame can specify HG instead. Because ARC provides OEM and ODM solutions for bicycle brands, wheel manufacturers and distributors, this configuration logic can be carried into a private-label programme rather than limited to a catalogue SKU.
What the specification should not do is assume that a freehub option exists because the hub is Boost-spaced. Each configuration needs to be confirmed against the supplier's current specification sheet for the exact model and variant being ordered.
What to verify before ordering
Procurement teams can reduce most freehub-related risk by confirming a short list of points before the purchase order is raised.
- Freehub standard per variant: confirm in writing which of HG, Micro Spline or XD applies to each SKU or build tier being ordered, and that the specification sheet names the standard explicitly rather than describing it generically.
- Cassette fit on a sample: mount the intended cassette on a sample freehub body and check spline engagement, lockring torque and outboard position, especially with the largest cog.
- Boost spacing and axle configuration: verify 15×110mm front and 12×148mm rear against the frame drawings, and confirm end caps match the intended axles.
- Ratchet and engagement choice: confirm whether 36T or 54T is specified, and that this is recorded alongside the freehub standard rather than left to a later change.
- Spoke count and disc interface: confirm 28H, 32H or 36H drilling and the 6-bolt disc interface against the wheel build and rotor plan.
- Documentation consistency: check that the quotation, drawing and specification sheet all state the same freehub standard, so that a change at one stage does not silently diverge from the others.
For buyers specifying a Boost MTB hub set with a known drivetrain plan, the MT-065F/R is a reasonable candidate to put on the evaluation list: it covers the three freehub standards most MTB builds require, pairs them with Boost spacing and a choice of ratchet engagement, and comes from a manufacturer set up for OEM and ODM work. The next step is to confirm the exact freehub standard, ratchet count, spoke count and axle configuration for each build tier, and to validate cassette fit on a sample before the order is released.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China