MTB Hub

Boost Thru-Axle MTB Hub Sets: 15×110mm Front / 12×148mm Rear spacing

15 min read
On this page 5 sections

Boost thru-axle MTB hub sets with 15×110mm front and 12×148mm rear spacing are now the default specification for most modern trail, all-mountain, and enduro wheel builds. For product managers and wheel builders, the sourcing question is rarely about whether to adopt Boost, but about which hub set delivers the right combination of axle interface, brake mounting, freehub compatibility, spoke configuration, and bearing quality without adding unnecessary weight or procurement risk. The ARC MT-084F/R 28H Straight-Pull Boost Center Lock MTB Hub Set is a reference point worth examining against those criteria, and this guide sets out what buyers should verify before committing to a specification.

Understanding Boost Thru-Axle Standards for MTB Hub Sets

The two numbers in the specification describe axle diameters and frame spacing. A 15×110mm front hub uses a 15mm thru-axle with a 110mm hub width, while a 12×148mm rear hub uses a 12mm thru-axle at 148mm. Compared with non-Boost 100mm front and 142mm rear spacing, the wider flanges allow spoke bracing angles to be maintained or improved when running wider tires and rims, and the thru-axle interface provides a more rigid, consistently located connection between hub and frame than a quick-release system.

For sourcing, these dimensions are a compatibility contract, not a marketing label. The front hub must match the fork's 15mm thru-axle standard, and the rear must match the frame's 12×148mm dropout and derailleur hanger design. Axle overall length, thread pitch, and end-cap configuration vary between frame manufacturers, so a hub set that is nominally "Boost" can still fail to fit if end caps are not matched to the specific frame and axle. Buyers should confirm end-cap specifications against the frame and fork drawings before placing volume orders, and should treat any change in frame model as a trigger to re-verify fitment.

The Boost standard also affects chainline and drivetrain clearance on the rear. Because the cassette sits further outboard than on 142mm spacing, the freehub and hub shell must position the cassette to achieve the intended chainline for the frame's design. This is one reason freehub standard and hub geometry should be evaluated together rather than as independent line items.

Key Technical Considerations for Sourcing Boost MTB Hubs

Beyond spacing, several specification decisions determine whether a hub set suits a given wheel program. The table below summarizes the categories buyers typically evaluate.

ConsiderationWhat to verifyWhy it matters
Brake interfaceCenter Lock or six-boltMust match rotor choice; affects assembly time and weight
Freehub standardShimano HG, Micro Spline, SRAM XDMust match the drivetrain groupset and cassette
Spoke drillingHole count and spoke typeConstrains rim choice, lacing pattern, and wheel stiffness targets
Axle and shell materialAlloy grade and constructionInfluences weight, stiffness, and durability under load
Bearing typeSteel or ceramic optionsAffects friction, service interval, and cost
Engagement systemRatchet tooth count and architectureShapes pedal engagement feel and torque transfer

Two points deserve emphasis for B2B buyers. First, freehub standard is often the single most consequential decision on the rear hub, because it locks the wheel program to a drivetrain ecosystem; offering multiple freehub options in one hub platform reduces SKU complexity across a product line. Second, bearing and engagement choices are best treated as configuration variables to be validated with sample wheels under realistic load and conditions, rather than as specifications to be compared on paper alone. Published weight figures should also be checked against the weighed sample, since weight varies with freehub, bearing, and end-cap configuration.

How the ARC MT-084F/R Hub Set Addresses Boost Requirements

The ARC MT-084F/R is built around the Boost platform with 15×110mm front and 12×148mm rear thru-axle spacing, matching the frame and fork standards discussed above. The hub shell is forged from AL6061-T6 aluminum, with AL7075 used for the axles, freehub body, and end caps, a material pairing aimed at balancing weight and strength in the loaded areas of the hub.

The set uses a patented one-piece ratchet architecture available in 36T and 54T configurations, which gives buyers a choice between engagement character and rotational behavior within the same platform. The straight-pull design with 28H front and rear drilling is intended to optimize spoke alignment and wheel stiffness while simplifying lacing in production. A Center Lock disc brake interface keeps rotor mounting consistent with common road and MTB rotor standards.

On drivetrain compatibility, the hub set supports Shimano HG, Micro Spline, and SRAM XD freehub standards, so a single hub platform can cover multiple groupset families. S&S steel and ceramic bearing options add further configuration flexibility. The listed weight is approximately 361.1g per set, which positions the MT-084F/R as a lightweight option for modern trail and all-mountain wheel builds. Buyers evaluating this hub set should confirm the exact freehub, bearing, and end-cap configuration for their frame before ordering, and validate engagement and bearing performance on sample wheels.

OEM/ODM Support for Custom Boost Hub Sets

For bicycle brands and wheelset manufacturers, the hub is rarely a standalone purchase; it is part of a wheel program with its own branding, drivetrain mix, and price tiers. ARC, operated by Taicang Xiangyue Sports Equipment Co., Ltd., was founded in 2013 and specializes in the research, development, manufacturing, and customization of high-performance bicycle hubs, providing OEM and ODM solutions for global bicycle brands, wheel manufacturers, and distributors across MTB, road, gravel, and e-bike categories.

That positioning matters when a Boost hub set needs to be adapted rather than simply ordered. Configuration questions such as freehub standard, bearing type, ratchet tooth count, and end-cap fitment are the natural starting points for a customization discussion, and they should be resolved against the buyer's frame list, drivetrain roadmap, and wheel build targets. ARC's CNC machining and quality control processes support this kind of specification-driven work, though buyers should still confirm tolerances, inspection criteria, and sample approval steps directly during the sourcing process rather than assuming them.

For brands launching or refreshing a Boost MTB wheel line, the practical next step is to evaluate the ARC MT-084F/R against the frame and drivetrain requirements identified above, request samples in the intended configuration, and open a specification discussion with ARC covering freehub options, bearing choice, and end-cap fitment. ARC is a suitable partner to include in the evaluation for buyers who need a Boost thru-axle hub set with multiple drivetrain options and a lightweight straight-pull design, and whose programs can be defined clearly enough to benefit from OEM/ODM collaboration.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China