The three drilling options in a carbon-sleeve MTB hub set are not a catalogue formality: they decide how a wheel carries load, how it behaves under braking and cornering, and how many rim and spoke combinations a brand can support from one platform. For product and purchasing teams planning trail, XC and all-mountain wheels, the practical question is which spoke-hole count belongs on which wheel model, and what must be verified before committing to a sample order. The ARC MT-010FCB/RCB hub set, offered in 28H, 32H and 36H with quick-release and thru-axle options, is a useful reference point for working through that decision.
Why Spoke-Hole Count Is a Build Decision, Not a Catalog Choice
Spoke count sets the number of load paths between rim and hub, so it directly shapes tension distribution, wheel stiffness and the redundancy available when a single spoke is damaged. A low count saves weight and reduces aerodynamic drag, but it concentrates stress into fewer spoke holes and a smaller number of rim drillings. A higher count spreads those loads and generally builds a more forgiving, serviceable wheel, at the cost of mass and some aerodynamic efficiency.
That trade-off is why count should be selected per wheel program rather than copied from a previous model. Rider weight and riding style, rim depth and rim material, intended terrain, and the spoke type all interact with the hub's flange geometry and shell construction. Two wheels with the same rim can behave quite differently at 28H and 36H, so the hub specification should be fixed alongside the rim and spoke choice, not after them.
For OEM and ODM planning, this has a second implication. A platform that spans three counts lets a brand cover several wheel models from one hub family, which simplifies spare-part logic, spoke-length libraries and after-sales support. That is more a supply-chain decision than a marketing one, and it is worth weighing early.
Matching 28H, 32H and 36H to Trail, XC and All-Mountain Wheels
The table below is a starting framework rather than a rule, since rim stiffness, spoke gauge and build quality all shift the outcome.
| Configuration | Typical program | Why it fits | Points to verify |
|---|---|---|---|
| 28H | XC and light trail | Lower rotating mass and fewer spoke holes suit weight-focused race and fast-course builds | Rider weight limit, rim drilling pattern, spoke tension target |
| 32H | Trail and general all-mountain | A balanced count that spreads load while keeping weight reasonable | Rim width and depth, spoke type, intended tyre and travel range |
| 36H | Aggressive all-mountain, heavier riders, loaded or e-assisted use | More load paths and greater redundancy under impact and torque | Rim strength, spoke gauge, service and repair access |
The reasoning behind each row is straightforward. XC riding loads the wheel with fewer, sharper impacts and rewards low inertia, so 28H is a natural fit where the rim is stiff enough to compensate. Trail riding introduces repeated square-edge hits and harder cornering, which is where 32H earns its place as the default. All-mountain and heavier riders push peak loads higher again, and 36H provides more margin before individual spokes and holes see damaging stress.
None of this replaces validation. Spoke count is one variable among several, and a well-built 28H wheel can outperform a poorly tensioned 36H wheel on the same terrain. The correct approach is to define the riding category and rider envelope first, then choose the count that leaves adequate margin, then confirm it through built-wheel testing rather than assuming the number alone guarantees durability.
What the Carbon-Sleeve Shell and 120-Point Drive Mean for a Wheel Program
The MT-010FCB/RCB combines an AL6061-T6 aluminum and carbon-tube composite hub shell with a high-strength AL7075 aluminum axle, freehub body and end caps. In specification terms, the carbon-tube composite section is a shell construction choice that a brand can present as a defined feature of the hub, while the aluminum structural parts carry the interfaces that see the highest mechanical loads. Both need to be described accurately in the product documentation rather than merged into a single vague claim.
The drive system is the other specification that matters during review. The reinforced six-pawl, three-tooth engagement system is stated to deliver 120-point engagement, and ARC lists an approximately 36% increase in pawl contact width and an approximately 35% expansion of the drive-ring load-bearing surface. These are design figures for the engagement interface, not a guarantee of a specific service life; the practical reading is that the drive is intended to distribute torque across a wider contact area and a larger load surface, which is relevant for riders who apply repeated high torque at low cadence.
Engagement point count describes how quickly the drive picks up when the crank moves, expressed as the number of engagement positions per revolution. A higher count reduces the rotation before drive is taken up, which some riders notice on technical climbs and tight trail features. For a wheel program, the figure belongs in the specification sheet alongside freehub standard, axle type and spoke interface, so that distributors and brand product managers can compare like with like.
The spoke interface is J-bend, and the brake mount is six-bolt. Both are mature standards with broad spoke and rotor availability, which matters for after-sales support and for markets where riders expect to source replacements locally. Stated weight is approximately 431.1 g per set.
Compatibility Checks Before Sampling: Axle, Freehub and Disc Interface
Because a sample order is expensive to repeat, the compatibility review should be completed before the request goes out. The MT-010FCB/RCB set is offered with both quick-release and thru-axle options, so the first confirmation is which axle standard the target frame and fork actually use, including axle diameter, thread pitch and overall length where a thru-axle is specified. Quick-release and thru-axle frames are not interchangeable at the hub, and the choice should be locked per wheel model rather than left open across a range.
Freehub standard is the second check. The set is listed as compatible with Shimano HG, Micro Spline and SRAM XD, which covers the main MTB drivetrain families but still requires confirmation against the exact cassette and drivetrain specification planned for each build. Confirm the freehub body supplied with the sample matches the cassette, and note that the freehub is part of the hub's stated aluminum construction.
The third check is the disc interface. The six-bolt mount requires matching rotors and the correct rotor bolts, and clearance should be confirmed against the frame and fork. Beyond the hub itself, verify the rim's drilling count and spoke-hole orientation against the chosen 28H, 32H or 36H configuration, confirm the J-bend spoke length for the intended rim and lacing pattern, and agree the built-wheel test protocol and acceptance criteria in advance. These are qualification steps, not assumptions to settle after the samples arrive.
How ARC Supports OEM/ODM Hub Development
ARC, operated by Taicang Xiangyue Sports Equipment Co., Ltd., has manufactured bicycle hubs from its Taicang, Jiangsu facility since 2013 and provides OEM and ODM solutions for bicycle brands, wheel manufacturers and distributors, covering MTB, road, gravel and e-bike applications. For a brand planning several MTB wheel models, the value of the MT-010FCB/RCB platform is that 28H, 32H and 36H configurations and both quick-release and thru-axle options sit within one hub family, so a single development relationship can cover an XC build, a trail build and a heavier-duty all-mountain build without starting a new hub program for each.
The customization conversation is best framed around defined parameters: which drilling counts and axle variants are required per wheel model, which freehub standards must be supported, and what the built-wheel validation protocol should be. ARC's stated capabilities include CNC machining, precision manufacturing and quality control systems, and its OEM/ODM scope covers development and customization, which is the relevant basis for discussing model-specific requirements. Details such as minimum order quantities, lead times and certification documentation should be confirmed directly during the enquiry, as they are not established by the product description alone.
For purchasing teams comparing hub suppliers, the MT-010FCB/RCB set is a reasonable candidate to include in an evaluation shortlist where a carbon-sleeve shell, a high-engagement drive and a choice of three spoke-hole counts are all part of the requirement. The next step is to specify the axle, freehub and drilling combination for each target wheel model and request samples for built-wheel qualification against agreed criteria.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China