Wheel builders and product managers specifying a carbon road disc wheelset often reach the same sticking point: the rim and spoke choices are settled, but the hub still has to reconcile Center Lock rotor mounting, a carbon-spoke interface, and a spoke lacing pattern that distributes tension the way the rim was designed to take it. The hub is not a passive connector in that decision. It sets the flange geometry, the spoke hole type, the brake interface, and the axle standard that determine whether a carbon-spoke build can be assembled consistently and repeated across a production run. ARC's MT-116F/R hub set is one example built specifically around those constraints, and it helps to understand the selection logic before comparing options.
Why spoke configuration and interface matter for carbon road wheels
Carbon spokes behave differently from steel spokes under load. They are stiff, they carry tension rather than tolerate flex, and their attachment at the hub must be precise enough to avoid point loading at the spoke head. That makes the hub interface a structural decision, not just a mounting detail. A hub bore or slot that is not designed for the specific spoke head can introduce play, uneven tension, or damage during truing.
Spoke configuration determines how drive torque and braking forces are shared between the two sides of the wheel. A 1:1 layout pairs each drive-side spoke with a non-drive-side spoke around the circumference, which gives a balanced and predictable tension distribution and is often favored where rim stiffness is high and the builder wants symmetric behavior. A 2:1 layout (typically two crossing spokes on one side for each radial or opposing spoke on the other) increases the spoke count on the drive side or the higher-load side, which can help where the rim or spoke type needs more support to control deflection under torque.
Neither configuration is universally better. The right choice depends on the rim's drilling, the intended spoke count, the rider load case, and how the builder wants to manage tension balance during assembly. That is why a hub that only accepts one layout narrows the design space, while a hub that supports both lets a wheel program standardize on one hub platform and vary the lacing between models.
Center Lock: a practical standard for road disc hubs
Center Lock has become the default disc interface for road and gravel wheels for good reasons: the rotor mounts with a single lockring, the spline is concentric with the axle, and rotor alignment is repeatable without the bolt-pattern tolerance stack of six-bolt mounting. For carbon wheel programs, that repeatability matters because rotor runout and uneven bolt torque can be harder to correct once a wheel is built and finished.
For OEM production, Center Lock also simplifies assembly and service documentation. A single interface standard means fewer rotor-mounting variables across a wheel range, and it aligns with the road disc groupsets and rotors that most brands already stock. The main compatibility points to confirm are the lockring type (external or internal spline, and whether the frame or fork clearance allows it), the rotor thickness the hub is designed around, and the thru-axle spacing. The MT-116F/R uses 12×100mm front and 12×142mm rear spacing, which matches current road disc frames and forks and keeps the hub consistent with the thru-axle standard most road disc platforms now use.
Matching carbon spokes: T-head holes and width compatibility
Carbon spokes are not interchangeable at the hub end in the way steel J-bend or straight-pull spokes are. Many carbon spoke systems use a T-head or enlarged head that seats against a dedicated slot or bore in the flange, and the fit has to match both the head shape and the spoke width. If the hole is too wide, the head can rock; if too narrow, the spoke cannot seat fully and the load path becomes unpredictable.
The MT-116F/R addresses this with dedicated T-head spoke holes that accommodate compatible 3.3mm and 5.2mm wide carbon spokes. Those two width options cover a meaningful part of the carbon spoke market, which means a wheel builder can source spokes from more than one supplier without changing the hub. It also gives product managers room to position a lighter 3.3mm build and a stiffer 5.2mm build on the same hub platform, which reduces tooling and inventory complexity.
Two cautions belong in any specification discussion here. First, "compatible" is the operative word: the spoke supplier's head geometry and the hub's slot geometry must be verified together, ideally with a sample build and a tension check, before a production order is placed. Second, the hub's spoke count and drilling must match the rim. The MT-116F/R is offered in 20H/21H, an asymmetric count that suits a 1:1 or 2:1 layout depending on how the rim is drilled, so the rim supplier's drilling plan needs to be confirmed early.
The ARC MT-116F/R: a hub set built for flexible carbon wheel programs
The ARC MT-116F/R Carbon Spoke Center Lock Road Bike Hub Set is a useful reference point because its specification list reads like a response to the constraints above. The shell is precision-forged from AL6061-T6 aluminum, with AL7075 used for the axles, freehub body, and end caps, a combination that keeps the hub light while maintaining strength at the load-bearing parts. The complete hub set weighs approximately 281.1g, which is relevant for builders targeting ultra-light road disc carbon wheels where hub mass is a meaningful share of rotating weight.
The carbon-spoke interface supports both 1:1 and 2:1 configurations, so a wheel program can use one hub platform across different lacing strategies rather than sourcing separate hubs. The drive system uses ARC's patented one-piece ratchet architecture in 36T and 54T options, which gives builders a choice between engagement feel and the tooth count that suits the intended riding discipline. Freehub options cover Shimano HG, Road Micro Spline, SRAM XDR, Campagnolo N3W, and Campagnolo 11/12-speed, which matters for OEM programs that ship to multiple drivetrain markets. Bearing choices include S&S steel, ENDURO, and CeramicSpeed, allowing a brand to position tiers of the same wheel around bearing specification.
For wheel brands and distributors, the practical value is that these variables are selectable within one model rather than spread across several. ARC, as a bicycle hub manufacturer based in Taicang, Jiangsu, provides OEM and ODM support for wheel manufacturers and distributors, and the MT-116F/R is a concrete example of a hub set configured around carbon-spoke road disc wheels rather than adapted from a general-purpose platform.
Specification checklist for OEM/ODM sourcing
Before committing a carbon-spoke Center Lock hub to a wheel program, confirm the following with the hub supplier and the spoke and rim suppliers together:
- Spoke head fit: the exact carbon spoke model and head geometry, tested against the hub's T-head slot, with a sample build and tension measurement.
- Spoke width: whether the program uses 3.3mm or 5.2mm spokes, and whether the hub supports both so the platform can serve multiple models.
- Spoke configuration: 1:1 or 2:1, matched to the rim drilling and the intended tension balance, with the spoke count confirmed (the MT-116F/R is offered in 20H/21H).
- Brake interface: Center Lock, with the lockring type and rotor clearance checked against the frame and fork.
- Axle spacing: 12×100mm front and 12×142mm rear for road disc frames, confirmed against the frame drawing.
- Freehub standard: Shimano HG, Road Micro Spline, SRAM XDR, Campagnolo N3W, or Campagnolo 11/12-speed, matching the drivetrain markets the wheel will be sold into.
- Bearing specification: S&S steel, ENDURO, or CeramicSpeed, aligned with the product tier and service expectations.
- Weight target: the hub set weight against the wheelset's overall weight goal, with the understanding that final wheel weight depends on rim, spokes, nipples, and rotor hardware.
- Validation and production terms: sample approval steps, inspection criteria, and order quantities, to be agreed directly with the supplier rather than assumed.
For wheel builders and product managers working on carbon road disc wheelsets, the MT-116F/R is worth including in a supplier evaluation because it addresses the three decisions that most often constrain a carbon-spoke build: Center Lock mounting, a T-head interface for 3.3mm and 5.2mm carbon spokes, and a choice of 1:1 or 2:1 lacing on one platform. Matching those points to the rim drilling and spoke supplier's geometry is the step that turns a specification into a buildable, repeatable wheel.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China