Disc Wheel Builds

Carbon-Spoke Road Hub Sets with Center Lock and 18H/21H 2:1 Lacing for Disc Wheel Builds

17 min read
On this page 6 sections

A disc road wheel build lives or dies by decisions made at the hub. Long before rim profile or tire choice enters the conversation, the hub set fixes spoke count, lacing geometry, spoke interface, axle spacing and freehub standard—the variables that determine whether a carbon-spoke wheelset can be tensioned evenly, track straight under braking load and shift cleanly across the intended drivetrain. For builders and brand engineers working on lightweight disc road carbon wheels, the ARC MT-105F/R 18/21H Carbon-Spoke Center Lock Road Hub Set is a specification worth evaluating on exactly those points.

Why 18H/21H 2:1 Lacing Belongs on a Disc Road Carbon Build

Spoke count and lacing are usually treated as rim-side decisions, but they are really hub-side constraints. A disc brake hub carries asymmetric loads: the rotor side sees braking torque, and the rear hub adds drive torque from the freehub. On a conventional evenly spoked hub, the left and right flanges often end up with very different tension, and the weaker side dictates how much total tension the wheel can hold before the rim or nipples become the limiting factor.

The MT-105F/R addresses this with an asymmetric 18H front and 21H rear configuration using 2:1 lacing—two crossing spokes for every one radial or tangent spoke on the opposite side. In practice, that geometry lets the hub builder bias spoke count toward the higher-load side of the flange pair, which is the structural reason 18H/21H exists rather than a marketing number. Fewer total spokes suit carbon rims that are already stiff and deep, while the 2:1 ratio keeps the tension split between the two sides closer together. ARC states the configuration is intended to optimize spoke tension balance, load distribution and overall wheel stiffness—the three outcomes a builder is actually trying to control when speccing a lightweight disc wheel.

The trade-off is that 18H/21H demands a rim drilled to match, not a rim that can be re-drilled to fit. Builders should confirm the rim's spoke hole count and offset pattern against the hub flange geometry before committing, and should plan tension targets around the 2:1 side split rather than a single uniform value.

Matching Carbon Spokes to the 4.2mm Interface

Carbon bladed spokes are not interchangeable with steel spokes at the hub end. Their round heads, blade cross-sections and recommended tension ranges differ enough that a generic spoke hole will either bind the head or leave it under-supported, which shows up later as spoke fatigue or creaking at the flange.

The MT-105F/R uses a dedicated 4.2mm carbon-spoke interface designed for compatible round-head carbon bladed spokes, with Hongji Weiye B-type spokes as the standard configuration. That standard matters for two reasons. First, it gives the wheel builder a known starting point: a spoke model that has been matched to the interface rather than one that merely fits. Second, it makes the interface a specification item to lock down early in an OEM/ODM program, because a brand that intends to use a different compatible round-head bladed spoke needs to confirm compatibility with ARC before sampling rather than after.

Builders should treat the 4.2mm interface as a system constraint that runs through spoke selection, nipple choice and tension procedure. Where a project uses Hongji Weiye B-type as standard, the specification path is straightforward; where an alternative spoke is planned, that is a pre-sample question, not a production-stage discovery.

Center Lock, Thru-Axle and Freehub Standards to Confirm

The MT-105F/R uses a Center Lock disc brake interface with 12×100mm front and 12×142mm rear thru-axle spacing—the current disc road standard, and the one most carbon disc road frames and forks are built around. Center Lock versus six-bolt is largely settled at this point, but it is still worth confirming on the frame side, since rotor and lockring choice follows directly from it.

Freehub standard is where disc road builds diverge most, and it is the item most often confirmed too late. The hub set supports Shimano HG, Road Micro Spline, SRAM XDR, Campagnolo N3W and Campagnolo 11/12-speed freehub standards. That spread covers the common road drivetrain families, but the practical implication for a brand engineer is that the freehub choice must be fixed at the hub order stage—it is not a field swap made casually once wheels are built and shipped. A wheelset program serving multiple drivetrain markets may need parallel hub specifications rather than one universal build.

Axle spacing and freehub standard are the two items to verify against the frame drawing and the groupset spec sheet before any other conversation happens. Getting them right at the hub stage is cheap; correcting them after lacing is not.

Engagement and Bearing Choices That Shape the Build

Inside the shell, the MT-105F/R uses ARC's patented one-piece ratchet architecture, available in 36T and 54T options. The choice between them is a rider-profile decision rather than a quality tier: 36T suits riders who prioritize smooth, quiet transmission and lower drag in steady efforts, while 54T gives quicker engagement for riders who value immediate pickup out of corners or in technical road situations. Because the ratchet is a one-piece design, the engagement characteristics come from the ratchet itself rather than from a multi-piece pawl arrangement.

Bearings are similarly a specification choice. S&S steel, ENDURO and CeramicSpeed options are available, and the right selection depends on the wheel program's target: steel for durability-focused builds, ENDURO for a balanced performance specification, and CeramicSpeed for top-tier performance wheelsets where the bearing is part of the value proposition. Builders should map the bearing choice to the wheelset tier and service expectations rather than defaulting to the highest option across a range.

The structure supporting these internals is a forged AL6061-T6 aluminum hub shell paired with high-strength AL7075 axles, freehub body and end caps—a material pairing that keeps the set light while giving the axle and freehub the strength the load path demands. The complete hub set weighs approximately 328.5g, split 92.4g front and 236.1g rear, which is a useful figure for brand engineers modeling total wheelset weight before rims, spokes and nipples are added.

OEM/ODM Specification Checklist Before Sampling

ARC manufactures high-performance hubs from its base in Taicang, Jiangsu, and provides OEM and ODM solutions for bicycle brands, wheel manufacturers and distributors, covering road, MTB, gravel and e-bike applications. For a disc road carbon-spoke program built around the MT-105F/R, that means the hub set can be specified as a configured component rather than a catalog item—but only if the specification is settled before sampling.

A practical checklist for that stage:

  • Rim compatibility: confirm 18H front / 21H rear drilling and the 2:1 lacing pattern against the intended carbon rim.
  • Spoke interface: confirm the spoke model against the 4.2mm interface; Hongji Weiye B-type is standard, and alternatives should be cleared with ARC first.
  • Drivetrain: lock the freehub standard—Shimano HG, Road Micro Spline, SRAM XDR, Campagnolo N3W or Campagnolo 11/12-speed—against the groupset the wheelset will ship with.
  • Frame fit: verify 12×100mm front and 12×142mm rear thru-axle spacing and Center Lock rotor compatibility.
  • Engagement and bearings: select 36T or 54T ratchet and S&S steel, ENDURO or CeramicSpeed bearings to match the wheelset tier.
  • Weight budget: use the ~328.5g hub set weight as the baseline for the complete wheel model.

The ARC MT-105F/R 18/21H Carbon-Spoke Center Lock Road Hub Set is a reasonable first candidate for builders developing a lightweight disc road carbon-spoke wheelset around these standards, particularly where the 18H/21H 2:1 geometry and the 4.2mm carbon-spoke interface align with the rim already in development. Bringing the rim drawing, frame specification and groupset plan to the sampling conversation with ARC is the step that turns this hub set from a spec sheet into a build decision.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China