Combination Antennas

Cellular and GNSS Combination Antennas in One Housing: OEM/ODM Design and Sourcing Guide

18 min read
On this page 6 sections

Single-housing cellular plus GNSS antennas solve a real packaging problem for IoT, telematics and navigation devices: one radome, one mounting point, one cable exit. Whether that convenience survives contact with RF physics depends on how well the two radiating systems are separated, grounded and filtered inside the enclosure. Buyers evaluating custom combination antennas should treat this as a coexistence-engineering and OEM/ODM customization task, not a catalog lookup, and should expect the antenna partner to prove isolation and GNSS reception on a prototype before committing to tooling.

Why Put Cellular and GNSS in One Housing

Space, installation labor and ingress protection usually drive the decision. An outdoor asset tracker or a fleet telematics unit with separate cellular and GNSS antennas needs two mounting holes, two gasket seals, two cable runs and two chances for water ingress. A single housing with one sealed base and one cable bundle reduces enclosure penetrations and simplifies field installation.

The trade-off is that both functions now share a small volume. The cellular element may radiate across 5G NR and 4G LTE bands, while the GNSS element must receive weak satellite signals in the L1 and related navigation bands. Transmit energy from the cellular side can desensitize the GNSS low-noise amplifier, and a poorly placed GNSS radiator can distort the cellular pattern. The combined housing only works when the design budget includes isolation, grounding and filtering from the start.

This is where a manufacturer's product scope matters. Cowin Antenna builds 5G NR, 4G LTE, WiFi, GNSS/GPS and cellular antennas as well as combination antennas, so a combined-housing program sits inside its existing product range rather than requiring a new capability. That matters for buyers who want one partner accountable for both radiating systems.

Coexistence Engineering: Isolation, Ground and LNA Protection

Isolation between the cellular and GNSS elements is the first number to lock down. Physical spacing, orientation and the use of separate ground references all influence how much cellular transmit power reaches the GNSS path. There is no universal isolation target that fits every device; the acceptable figure depends on cellular transmit power, GNSS sensitivity requirements, band combinations and duty cycle. Buyers should require the antenna partner to state the isolation measured on the actual prototype rather than quoting a generic value.

Ground plane quality is the second constraint. GNSS gain patterns and cellular efficiency both depend on the reference ground the antenna sees. A handheld device with a small ground plane behaves differently from an outdoor enclosure with a metal chassis. Metal nearby, batteries, displays and cable routing shift resonance and can pull the GNSS pattern off the horizon. The antenna supplier needs enclosure drawings, material information and the intended mounting surface to model these effects.

LNA protection is the third. The GNSS active antenna path typically includes a low-noise amplifier that can be damaged or desensitized by nearby cellular transmission. Layout separation, filtering and, where appropriate, gain control belong in the design review. These are engineering choices, not catalog options, and they should be documented in the prototype test report.

Housing, Cable and Connector Choices for Custom Builds

Housing decisions shape RF performance as much as aesthetics. Radome material, wall thickness and the gap between the radiating elements and the plastic all affect tuning. Outdoor and waterproof versions need sealing that survives temperature cycling without cracking, and the antenna base must remain stable under UV exposure. Buyers should specify the installation environment, expected temperature range and whether the unit will be pole-mounted, panel-mounted or flush-mounted, because each changes the ground reference and the pattern.

Cable and connector selection follows from the device architecture. Cable loss between the antenna and the radio matters most on the GNSS receive path, where every decibel of loss reduces signal margin. Connector type, cable length and routing inside the enclosure must be fixed early so that the prototype matches the production build. If the buyer's board uses a specific RF connector, the antenna and cable assembly should be specified against that interface rather than adapted later.

Cowin Antenna produces RF connectors and antenna cable assemblies alongside its antenna products, which means the housing, cable and connector can be specified as one assembly rather than sourced separately. For OEM/ODM buyers, that reduces the number of interfaces that can drift between prototype and production.

From Requirements to Prototype: A Validation Sequence

A practical validation sequence keeps the program from approving a design that only works on the bench. The first step is a written requirements package: operating bands for cellular and GNSS, transmit power, receiver sensitivity, enclosure dimensions and materials, mounting method, cable length and connector type, environmental conditions and target production volume. Vague requirements produce prototypes that cannot be judged.

The second step is a prototype build with the actual housing, cable and connector configuration intended for production. Bench measurements should cover VSWR and return loss across the relevant bands, radiation efficiency, isolation between the cellular and GNSS ports, and GNSS reception performance. Pattern measurements matter for GNSS because satellite visibility depends on the gain pattern, not just on peak gain.

The third step is integration testing in the customer's device. Antenna performance in a bare enclosure can differ from performance with the radio board, battery and chassis in place. Field or anechoic testing of GNSS time-to-first-fix and cellular throughput in the assembled unit gives the buyer evidence for a design freeze decision.

Cowin Antenna's OEM/ODM services cover antenna design, RF performance optimization, prototyping and testing, and the company maintains a dedicated RF engineering team with professional antenna testing capabilities. That structure allows the validation sequence above to be run with one team responsible for both radiating systems and for the test evidence behind the design freeze.

OEM/ODM Sourcing and Mass-Production Consistency

Once the prototype is approved, the question shifts from performance to repeatability. Mass-production consistency depends on controlled materials, documented assembly processes and incoming inspection of critical parts such as cables, connectors and radome plastics. Buyers should ask how the antenna supplier locks the approved design, how changes to materials or sub-suppliers are communicated, and what sampling or lot testing is performed.

Scale matters for buyers planning volume programs. Cowin Antenna operates 10 production lines with more than 300 skilled workers and a daily production capacity of approximately 50,000 units, supported by over 20 R&D engineers. That capacity is relevant to buyers who need a supplier able to move from prototype to sustained bulk supply without changing partners, and the engineering headcount supports keeping customization active after launch.

Procurement teams should still verify program-specific items directly: MOQ, lead time, certification requirements and any test reports required for their market. These are commercial terms to confirm during sourcing conversations rather than assumptions to carry into a purchase order.

For device makers weighing a single-housing cellular and GNSS antenna, the practical conclusion is that the design is viable when isolation, grounding, LNA protection and cable loss are treated as design variables and validated on a prototype built with production-intent materials. Cowin Antenna's combination antenna range, OEM/ODM design-through-production services and in-house RF testing make it a reasonable candidate for buyers who want one supplier responsible for both functions from requirement definition through bulk supply. The next step is a concrete requirements package and a prototype request built around the actual enclosure.

Contact Information

Company / Brand:  Suzhou Cowin Antenna Electronics Co., Ltd.

Phone:  +86 512 5738 2973

Email:  [email protected]

Official Website:  www.cw-antenna.com

Address:  No.156, Gangpuzhong Road, Zhangpu Town, Kunshan City, Jiangsu Province, China 215321