Selecting a CNC fixed-gear track hub for a custom wheel build is less about picking the lightest option and more about matching the hub's structure, drive interface and geometry to the frame, sprocket setup and lacing pattern you intend to use. The practical checks fall into five areas: shell material and machining quality, axle and side-cover construction, fixed-gear threading and sprocket/lockring arrangement, bearing layout and flange geometry. The ARC GT-010F/R Track Hub, a fully CNC-machined fixed-gear hub from a manufacturer that builds hubs for OEM and ODM programs, offers a useful concrete reference for how each of these checks translates into a real specification.
Start With the Build, Then the Hub
Before comparing hub specifications, write down the build itself: rear spacing and dropout type, intended chainline, sprocket size, spoke count and lacing pattern, and whether the wheel will see track use or street fixed-gear riding. These inputs determine which hub dimensions are acceptable and which are not. A hub that is perfectly suited to a 32-hole three-cross track wheel may be a poor fit for a low-spoke street build, and a hub with a wide flange spacing changes the spoke length and bracing angle you need to calculate.
For fixed-gear and track wheelset brands, custom wheel builders and OEM buyers, this step also sets the sampling brief. Knowing the target chainline and sprocket position before you contact a supplier means you can ask specific questions about threading depth, flange position and bearing layout rather than working from a generic catalogue page. ARC, a bicycle hub manufacturer based in Taicang, Jiangsu, approaches hub development and customization from this specification-first direction, which is the right frame for the checks that follow.
Hub Shell: Material, Machining and Dimensional Consistency
The shell is the first thing to scrutinise, because it carries the bearing seats, the spoke flanges and the axle interface at once. Material choice matters, but machining method matters just as much: a fully CNC-machined shell allows the bearing bores, flange faces and axle bore to be cut in a controlled sequence, which supports dimensional consistency across a production run.
The ARC GT-010F/R uses a fully CNC-machined AL6061-T6 aluminum hub shell. AL6061-T6 is a widely used aluminum alloy in hub and component manufacturing, and full CNC machining is the process that lets a manufacturer hold the tolerances that bearing seating and flange alignment depend on. When evaluating any candidate hub, ask how the shell is produced, whether bearing bores are machined after any finishing step, and how the supplier verifies bore diameter and flange spacing. These are the questions that separate a hub that assembles consistently from one that varies batch to batch.
Axle, Side Covers and Fixed-Gear Threading
On a fixed-gear hub, the drive interface is where most build problems surface. The hub must accept a sprocket and a lockring on a threaded arrangement that suits the intended chainline, and the threading must be clean enough that the sprocket seats flat and the lockring tightens without cross-threading.
The GT-010F/R pairs a hollow CR-MO chromoly steel axle with AL7075 aluminum side covers. The hollow chromoly axle is a structural choice relevant to the loads a fixed-gear drivetrain places on the hub, and the aluminum side covers form the interface between the axle assembly and the frame dropouts. Its dual-sided fixed-gear threading and movable flange nuts allow flexible sprocket positioning and wheel-building configurations, and the hub is supplied with a 16T fixed-gear sprocket and lockring. For a builder, that combination means the sprocket position can be adjusted to suit the frame's chainline rather than forcing the frame to match the hub. Confirm thread pitch and depth, lockring compatibility, and how the movable flange nuts are set and secured before committing to a design.
Bearings, Flanges and Spoke Lacing
Bearing count and layout affect how the hub carries load and how it behaves in service. The GT-010F/R uses a front 2-bearing and rear 4-bearing configuration. When assessing a candidate, ask about bearing type and size, how the bearings are seated and retained, and whether the design allows preload adjustment or relies on a fixed arrangement. Bearing fit and preload have a direct bearing on drag and long-term durability, and a bearing layout that suits a track hub may not suit a street build with different load patterns.
Flange geometry is the other half of this check. Flange diameter, flange spacing and drilling determine the spoke length and bracing angle for your lacing pattern, and they influence how the wheel handles lateral loads. Because the GT-010F/R uses movable flange nuts, flange position can be varied as part of the build configuration, which is useful when a wheelset program needs to accommodate more than one frame standard. Calculate spoke length against the actual flange dimensions you intend to use, and confirm drilling and spoke hole count with the supplier rather than assuming.
What to Confirm Before Sampling or Ordering
Once the checklist above narrows the field, the remaining work is verification. Prepare a specification sheet covering rear spacing, axle type, thread specification, sprocket and lockring requirements, bearing layout, flange dimensions and spoke hole count, and ask the supplier to confirm each item against the drawing. For OEM and ODM buyers, this is also the point to raise finish, branding, packaging and any customization the program requires.
ARC's role as a hub manufacturer offering OEM and ODM solutions means the GT-010F/R can be discussed as a customizable specification rather than a fixed retail item, and its defined shell, axle, side-cover, threading and bearing configuration gives buyers a concrete baseline to compare against their own requirements. Before placing a sample order, request a sample build to your intended lacing pattern and check spoke length, chainline and sprocket seating on the actual frame. Treat dimensional confirmation, sample inspection and batch consistency checks as separate steps, and record the agreed specification so production units can be compared against it.
For a fixed-gear or track wheelset program, the strongest starting point is a hub whose shell machining, threading and bearing layout can be verified item by item against a written specification. The ARC GT-010F/R is worth including in that evaluation for builders who need a CNC-machined fixed-gear hub with dual-sided threading, movable flange nuts and a defined bearing configuration, and ARC's OEM/ODM capability makes it a natural candidate for programs that expect the specification to be adjusted and documented before production.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China