Entry-level mountain bike hub sets are often specified by a single number: 28H, 32H or 36H. Yet that number is not a quality grade. It is the spoke-hole count per hub, and it sets the boundaries for how a wheel can be built, how much redundancy the spoke bed carries, and how easily the wheel can be serviced in the field. For buying teams at bicycle brands, wheelset assemblers and distributors, the practical question is which drilling matches the wheel program the hub set will feed. ARC, a hub manufacturer based in Taicang, China, supplies its MT-001FS/RS entry-level MTB hub set in all three drillings, which makes the comparison concrete rather than theoretical.
Start From the Wheel Program, Not the Number
Before comparing 28H, 32H and 36H, it helps to describe the wheel the hub set must serve. Three variables usually decide the drilling: the intended riding category, the rim the builder already sources, and the service environment the finished bike will meet.
Rim availability is the first filter. A hub with 32 holes can only be laced to a 32-hole rim, so an entry-level program that already holds stock of a particular rim is effectively committed to the matching hub drilling. Buyers who are still finalising the rim should shortlist the hub drilling and the rim together, not sequentially.
Riding category is the second filter. Everyday trail and entry-level MTB use involves repeated low-amplitude loads, occasional impacts and, on fleet or rental bikes, minimal maintenance attention. That profile rewards spoke redundancy and predictable service over minimum weight.
The third filter is the build and service chain. A wheel builder who laces wheels by hand may value a familiar, widely supported interface; a distributor supporting many small workshops may want a configuration that is easy to explain and to re-order. Treating 28H, 32H and 36H as three build programs, each with its own rim, lacing and service implications, is a more reliable way to choose than picking the middle number by habit.
What 28H, 32H and 36H Change in Practice
The most direct effect of the drilling is the number of spokes carrying the load between rim and hub. More spokes share the same rider input, so each spoke and each spoke hole in the flange works at a lower individual load. That is a structural argument for higher counts on wheels expected to absorb rougher treatment.
The second effect is spoke redundancy. A 36H wheel can lose a spoke and still retain a workable distribution of tension around the rim; a 28H wheel has less margin, and a single failure is more noticeable. For rental fleets, bike-share maintenance teams or distributors supporting riders in remote areas, that margin can matter more than the small weight difference.
The third effect is build flexibility. Higher hole counts open up more lacing patterns and give builders more room to tune tension balance between the drive and non-drive sides. Lower counts simplify the build, reduce the number of components to stock and keep spoke inventory lean — an advantage for assemblers running tight SKUs.
| Drilling | Practical character | Typical fit |
|---|---|---|
| 28H | Fewer spokes, simplest build, lightest spoke inventory; least redundancy | Light everyday use where weight and SKU simplicity are priorities |
| 32H | Balanced spoke count and build options; moderate redundancy | The broad middle ground for entry-level trail and general MTB |
| 36H | Highest spoke redundancy and tension margin; more spokes to stock and tension | Fleet, rental and heavier-duty everyday use |
None of these configurations is inherently stronger in every respect; the outcome depends on the rim, spoke specification, lacing and build quality as much as on the hole count.
Matching the Drilling to Entry-Level MTB Use
For an entry-level trail bike sold through dealers, 32H is usually the easiest specification to defend. It leaves room for a range of rim choices, offers reasonable spoke redundancy, and does not push the build into unusual lacing patterns. It is also the count most workshops expect, which keeps after-sales conversations simple.
28H suits programs where the wheel is part of a lighter, simpler build and where the rider is unlikely to ride far from support. It reduces the number of spokes in the build and can trim rotating weight, but the buyer should accept a smaller margin if a spoke is damaged.
36H is the conservative choice. It fits rental fleets, heavy riders, loaded everyday bikes and any program where a wheel must keep running after minor damage. The trade-off is a marginally heavier wheel and a slightly longer build.
A useful way to frame the decision is to ask what happens after a single spoke failure. If the answer must be "the rider keeps riding to the nearest workshop", the higher count deserves serious weight. If the answer is "the bike returns to the dealer", the lower count is defensible.
Options to Confirm Alongside the Drilling
The drilling is only one line on the specification sheet. For the ARC MT-001FS/RS hub set, several other choices sit alongside it and should be settled in the same conversation.
The spoke interface is fixed by the design: the hub set uses a J-bend spoke pattern, a familiar format that most wheel builders already handle and that keeps spoke sourcing straightforward. Confirm this against the spokes already in the buyer's inventory.
The freehub standard is a separate decision. The hub set is compatible with Shimano HG, Micro Spline and SRAM XD, so the drilling choice does not restrict the drivetrain; the buyer should state the freehub body required per SKU rather than assume a default.
Bearing specification is another axis. The hub set offers S&S steel, ENDURO and CeramicSpeed bearing options, which lets a buyer align bearing choice with price positioning and the service regime the finished bike will see. Entry-level fleet bikes and premium dealer builds may not warrant the same bearing selection.
The engagement system also deserves confirmation. The MT-001FS/RS uses a 3-pawl, single-tooth engagement design with a simple structure intended for straightforward maintenance — a practical point for distributors supporting many small workshops. The hub shell is AL6061-T6 aluminium, while the axle, freehub body and end caps use AL7075 aluminium; the 6-bolt disc interface keeps rotor choice conventional.
Specifying the ARC MT-001FS/RS Hub Set
For buyers who need one hub set family to cover different spoke-count programs, the ARC MT-001FS/RS entry-level MTB hub set is a practical starting point: it is offered with 28H, 32H and 36H configurations, so a single model can serve a lighter build, a mainstream trail bike and a heavier-duty fleet wheel without splitting the supplier base. The ARC MT-001FS/RS 28/32/36H 6-Bolt QR MTB Hub Set is the specific product to evaluate for that role.
The confirmation list before ordering should cover the drilling per SKU, the freehub standard, the bearing option and the spoke interface, together with the rim the wheel will use. ARC's OEM and ODM work for bicycle brands, wheel manufacturers and distributors means these choices can be discussed as a configuration exercise rather than a fixed catalogue pick, though final specifications, lead times and commercial terms should be confirmed directly with the supplier.
Where the wheel program calls for a mainstream 32H build, a lighter 28H build or a more conservative 36H fleet wheel, the MT-001FS/RS hub set is worth placing on the evaluation list, with the drilling decision made alongside the rim and service plan rather than in isolation.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China