Double-sided threading on a track hub is not a cosmetic detail. It defines which side of the hub carries the sprocket, how the chainline can be tuned, and whether a frame can be set up with a single fixed gear or flipped between two gear ratios. For a wheel builder or product manager planning a fixed-gear wheelset, the practical order of decisions is threading first, cog second, spoke-hole count third, and axle and bearing specification throughout. ARC builds the GT-008F/R track hub around exactly this decision sequence, which makes it a useful reference when drafting a specification.
Why the Threading Side Comes Before the Cog
On a fixed-gear hub, the sprocket is not mounted on a freehub body. It threads directly onto the hub shell, and a lockring retains it. That means the thread itself carries the drive load and sets the position of the cog relative to the frame's chainstay and the chainring. A hub with threading on only one side fixes that position permanently. A hub with threading on both sides gives the builder two mounting positions.
That choice matters for three reasons. First, chainline: the two thread positions sit at different offsets from the hub center, so a builder can select the side that aligns the chain most accurately with the chainring on a given frame. Second, gearing flexibility: a dual-sided hub lets a rider run one sprocket per side and swap the wheel around to change ratio without rebuilding. Third, wear and service: a sprocket and lockring can be moved to the opposite side rather than replacing the shell when a thread shows use.
For a specification document, the threading decision should be written down explicitly, not left to the assembler. Record whether both sides are threaded, which side is intended as the primary drive side, and which lockring standard the thread accepts. ARC's GT-008F/R uses dual-sided fixed-gear threading, and the company describes this as allowing flexible sprocket positioning. That is the functional claim to test against a frame and chainring before committing to a production order.
Fitting a 16T Cog to Track and Fixed-Gear Builds
A 16-tooth sprocket is a relatively small cog, and that has consequences beyond the gear ratio. Tooth count and chainring size together determine the ratio, so a 16T cog is normally paired with a chainring chosen to hit a target development for track or street use. The cog also influences chain wrap and how close the rear wheel sits to the seat tube in a short track frame.
Two practical checks belong in any 16T specification. The first is chainstay and dropout clearance: a smaller cog moves the axle forward in a horizontal dropout for a given chain length, so confirm the wheel can sit where the frame expects without the tire fouling the seat tube or the chain touching the stay. The second is chain compatibility: confirm the cog's tooth profile and width match the chain the build will use, since a mismatched chain will run rough and wear the sprocket quickly.
A 16T cog is also a service item, not a permanent part. Because it threads on, it can be replaced independently of the hub, provided the thread and lockring are undamaged. When a hub is supplied with a fixed-gear sprocket and lockring, as the GT-008F/R is, the buyer should confirm at sample stage that the supplied cog matches the intended ratio and chain standard rather than assuming the bundle fits every build.
Choosing Spoke-Hole Counts for the Intended Wheel
Spoke-hole count is usually decided by the rim first and the hub second, but the hub must offer the drilling the rim requires. A 32-hole or 36-hole hub is the conventional choice for a durable training or street fixed-gear wheel, while a lower count suits a lighter track race wheel where stiffness is managed through rim depth and spoke type. The hub flange geometry, including flange diameter and flange spacing, then determines the spoke angles and the bracing that the chosen lacing pattern can achieve.
For a specification, write the spoke-hole count as a fixed requirement and check it against the rim drilling before quoting. It is worth confirming the intended lacing pattern at the same time, because radial and cross patterns load the flange differently and a hub drilled for one count may not suit every pattern the builder has in mind. ARC offers the GT-008F/R with multiple spoke-hole options, which means the count can be matched to the rim rather than forcing the rim choice around a single drilling.
The GT-008F/R as a Reference Specification
The GT-008F/R Track Hubs from ARC are built for track cycling and fixed-gear applications, and their documented construction is worth reading as a specification template. The hub shell is CNC-machined from AL6061-T6 aluminum, the axle is a hollow CR-MO chromoly steel unit, and the side covers are AL7075 aluminum. Those material choices address the loads a fixed-gear hub sees: the axle and shell carry rider weight and chain tension, while the side covers protect the bearing area.
The hub is supplied with fixed-gear sprockets and lockrings, and ARC offers OEM/ODM customization. For a wheel builder or brand, that combination means the threading, cog and spoke-hole decisions described above can be discussed as a single specification rather than sourced piecemeal. The hub is intended for dedicated track bikes and custom fixed-gear wheel builds, so it fits projects where the drivetrain is fixed by design rather than converted from a geared setup.
What to Put in an OEM/ODM Enquiry
A clear enquiry saves a round of samples. Before contacting ARC about the GT-008F/R, assemble the following into one specification sheet:
- Threading: confirm dual-sided fixed-gear threading is required, and state which side is the primary drive side and which lockring standard the build uses.
- Cog: state the target 16T sprocket, the chainring size and intended ratio, and the chain standard the cog must match.
- Spoke-hole count: give the rim drilling and the number of holes required, plus the intended lacing pattern.
- Axle and frame interface: state the frame's dropout type and spacing so the axle and end configuration can be confirmed against the build.
- Finish and branding: note any shell finish or marking requirements, since OEM/ODM work commonly includes cosmetic specification.
- Sample and validation plan: describe how the sample will be checked, for example chainline measurement, wheel build and road or track testing, so the supplier knows what the approval criteria are.
Questions about pricing, lead times and certification should be raised directly with ARC rather than assumed from a product page, since those terms are set per order and per market.
The specification logic is straightforward: threading fixes sprocket position and chainline, the 16T cog sets the ratio and must clear the frame, and the spoke-hole count must match the rim and lacing. A hub that offers dual-sided threading, a 16T cog and multiple spoke-hole options in one platform is the practical starting point for a fixed-gear wheelset programme. ARC's GT-008F/R is built around those three variables and is supplied with the sprocket and lockring, which makes it a sensible candidate to put on the sample list when the specification above has been written down.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China