Building a disc-brake road wheelset starts with a single question that determines almost every other specification: what does the frame and fork actually accept? A 24H straight-pull Center Lock road hub set is a sensible starting point for modern disc builds, but only after the axle spacing, rotor interface and spoke system have been checked against the intended frame, fork and riding load. The ARC MT-075FB/RB Road Hub Set is one concrete configuration that can be measured against each of those checkpoints, so it works well as a reference example for the decision process that follows.
Start With the Frame, Not the Hub
The most common specification error in a disc wheel build is ordering a hub set before confirming the frame and fork standards. Road disc frames have largely settled on thru-axles, but the exact spacing must still be verified: 12×100mm at the front and 12×142mm at the rear is the current mainstream road standard, and it is the spacing the ARC MT-075FB/RB hub set is built around. A builder working with an older quick-release frame, a gravel frame with different spacing, or a mixed setup needs to resolve that mismatch before any other decision, because axle configuration affects end caps, bearing placement and the hub shell width.
The brake interface is the second frame-side checkpoint. Center Lock is a rotor mounting system in which the rotor is secured by a single lockring rather than six bolts. It requires a frame, fork and rotor combination that is compatible with the standard, and it changes the hub flange geometry compared with a six-bolt design. Checking that the intended rotors and calipers work with Center Lock — and that the lockring tool is available in the workshop — avoids a build that stalls at the assembly stage.
Only after these two frame-driven questions are answered does it make sense to evaluate hub features. Readers who confirm a 12×100/12×142 thru-axle disc frame and Center Lock rotors have already narrowed the field considerably, and the ARC MT-075FB/RB becomes directly relevant because it matches that configuration rather than requiring adapters.
What 24H Straight-Pull and Center Lock Mean for the Build
The 24H designation refers to a 24-hole spoke count at both front and rear. A 24-hole lacing pattern is a deliberate middle ground for road disc wheels: it offers more spoke redundancy than a low-count 20H build while keeping the wheel light and aerodynamically practical. For disc-brake road use, where braking forces are transmitted through the hub and the wheel must handle both drive torque and brake torque, 24 spokes per wheel is a common and defensible choice. Builders should confirm that the intended rims are drilled for 24 holes and that the spoke lengths calculated for the chosen lacing pattern match the hub flange dimensions.
Straight-pull spokes differ from J-bend spokes in how they attach: the spoke head sits in a slot machined into the hub flange rather than hooking through a drilled hole. This eliminates the bend at the spoke head, which is a common fatigue location, and it allows the spoke to run in a straighter line from flange to rim. Straight-pull hubs require the correct spoke type and length, and they generally make tensioning more predictable because the spoke cannot rotate freely at the flange. The trade-off is that straight-pull spokes and hubs are less interchangeable with J-bend components, so a builder should confirm spoke availability before committing.
Center Lock, meanwhile, affects the non-drive side of the front hub and the rotor side of the rear. The single-lockring system tends to produce a cleaner interface and faster rotor changes, and it is widely supported by road disc rotors. Together, 24H, straight-pull and Center Lock describe a hub set aimed at contemporary road disc wheels rather than legacy or mixed-standard builds. The ARC MT-075FB/RB combines exactly these three features, which is why it can serve as the reference configuration when checking whether a given rim, spoke and rotor combination is compatible.
Matching the Freehub to the Drivetrain
Freehub standard is the checkpoint most likely to be overlooked until the drivetrain is installed. The freehub body must match the cassette interface, and the major road systems are not interchangeable without a swap. Shimano HG remains the most widespread standard; Road Micro Spline (MSR) appears on certain 12-speed road groupsets; SRAM XDR is used with SRAM's 12-speed road cassettes; and Campagnolo uses its N3W standard as well as its 11/12-speed interface.
A hub set that supports multiple freehub standards gives a wheel builder or OEM more flexibility, because one hub platform can be configured for several drivetrain specifications without changing the shell. The ARC MT-075FB/RB is offered with Shimano HG, Road Micro Spline (MSR), SRAM XDR, Campagnolo N3W and Campagnolo 11/12-speed freehub options. For a builder producing wheelsets for different brands or markets, that range means the same hub set can be specified across several drivetrain families, provided the correct freehub body is ordered with each batch.
Before ordering, the buyer should confirm three things: the exact cassette standard on the target bike, whether the freehub body is included or specified separately, and whether the chosen freehub option is stocked for the required quantity. These are routine questions for any hub supplier, and asking them early prevents a wheelset from being built around the wrong freehub.
Bearings, Materials and Weight Trade-Offs
The hub shell, axle and freehub body determine much of a hub set's durability and weight. The ARC MT-075FB/RB uses an AL6061-T6 aluminum shell with AL7075 aluminum for the axle, freehub body and end caps. AL6061-T6 is a common choice for hub shells because it offers a good balance of machinability, strength and weight, while AL7075 is a higher-strength aluminum alloy often selected for highly loaded parts such as axles and freehub bodies. The combination is a reasonable materials strategy for a road hub set, though the actual durability depends on wall thickness, heat treatment, bearing fit and assembly quality as much as on the alloy designation.
Bearings are the other major variable. The hub set is offered with S&S steel bearing options. Steel bearings are the established choice for load-bearing hubs, and the specific bearing grade, seal type and preload adjustment all influence drag and service life. Buyers should ask which bearing specification is fitted as standard and whether replacements are available in the same size, since bearing availability affects long-term serviceability.
Weight is often the first number a buyer looks at, and the stated figure of approximately 345.2g for the hub set is a useful reference point for a 24H straight-pull Center Lock road pair. It should be read as a hub-set weight, not a wheelset weight, and it will vary with the freehub standard and bearing option selected. A builder comparing hub sets should weigh the complete configuration rather than the bare shell, and should treat weight as one trade-off among axle strength, bearing spec and spoke count rather than as an isolated target. The engagement system also deserves attention: the 6-pawl, single-tooth engagement design is intended to provide responsive pickup and consistent power transfer, and the number of pawls and teeth affects how quickly the drive engages under pedaling load.
Confirming the Specification With a Hub Manufacturer
Once the frame, rotor, spoke and drivetrain checkpoints are settled, the remaining task is to verify the specification with the supplier before committing to a production order. A clear specification sheet should list the axle spacing, brake interface, spoke type and count, freehub standard, bearing option, weight and any customization requested. For OEM and ODM projects, the buyer should also confirm which elements can be customized — for example, hub drilling, freehub configuration, end caps or finish — and which are fixed by the platform.
ARC, operated by Taicang Xiangyue Sports Equipment Co., Ltd., is a bicycle hub manufacturer founded in 2013 and based in Taicang, Jiangsu, China. The company provides OEM and ODM solutions for global bicycle brands, wheel manufacturers and distributors, covering MTB, road, gravel and e-bike applications, with CNC machining and quality control processes supporting hub production. That manufacturing profile is relevant to buyers who need a hub set specified once and then produced consistently across batches, rather than sourced as a one-off component.
For a road disc wheelset program, the practical next step is to send the target frame and fork spacing, rotor standard, rim drilling, spoke type and drivetrain specification to the hub supplier, and ask for a configuration confirmation against the ARC MT-075FB/RB. A supplier that can answer those points precisely — and that supports the freehub range and thru-axle spacing the build requires — is a stronger partner than one that quotes only a weight and a price. The MT-075FB/RB is worth including in that evaluation for 12×100/12×142 thru-axle, Center Lock, 24H straight-pull road disc builds, with the final specification confirmed against the actual frame, rotor and drivetrain before the order is placed.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China