Mountain bike hub specification starts with a single question that decides whether a wheel build will even fit the frame in hand: what spacing does the frame expect? For a large share of entry-level and recreational MTBs, the answer is 9×100mm at the front and 10×135mm at the rear, both secured with quick-release skewers. Those figures are not marketing shorthand. They describe a dropout system, an axle format, and a set of dimensional constraints that flow through the entire wheel build.
What 9×100mm and 10×135mm Quick-Release Spacing Actually Means
The first number in each pair is the axle diameter in millimeters; the second is the hub's over-locknut distance (OLD), the width measured across the hub from locknut face to locknut face. A 9×100mm front hub therefore uses a 9mm quick-release axle and measures 100mm across its locknuts. A 10×135mm rear hub uses a 10mm quick-release axle and measures 135mm across.
The distinction between diameter and width matters because each dimension answers a different question. The 100mm and 135mm figures determine whether the hub drops into the frame or fork. The 9mm and 10mm figures describe the axle interface and the dropout slot the quick-release skewer passes through. A hub can match the width but not the axle format, or vice versa, and either mismatch stops the build.
This is the classic quick-release standard that dominated mountain bikes before thru-axles spread through performance segments. It remains the reference format for recreational hardtails, entry-level full-suspension frames, kids' and youth MTBs, and many hybrid-adjacent builds. For buyers specifying hubs at this level, 9×100mm front and 10×135mm rear is not a legacy detail to work around; it is the target specification.
Frame Compatibility and Axle Retention
Compatibility begins at the dropouts. A fork with 100mm-spaced quick-release dropouts accepts a 9×100mm front hub; a frame with 135mm-spaced quick-release dropouts accepts a 10×135mm rear hub. Frames built around thru-axles use different dropout geometry and cannot be adapted by swapping end caps alone, which is why confirming the frame and fork standard is the first step in any hub selection.
The quick-release system itself is worth understanding as a retention method. A skewer passes through the hollow axle, and a cam lever compresses the dropout faces against the locknuts. Correct retention depends on the axle ends seating properly in the dropout slots, the skewer being the right length for the hub width, and the cam being closed with appropriate force. A hub whose OLD matches the frame but whose end caps or axle ends are designed for a different dropout profile can sit loosely, which is a fit problem rather than a spacing problem.
For OEM and wheel-building buyers, this translates into a practical checklist before ordering:
- Confirm the frame and fork are specified for quick-release dropouts at 135mm rear and 100mm front respectively.
- Confirm the dropout slot accepts a 9mm front and 10mm rear axle end.
- Check that the supplied skewer matches the hub width and dropout thickness.
- Verify disc brake mounting separately, since rotor interface is a hub feature, not a spacing feature.
The ARC MT-001FG/003RC hub set is built around exactly these dimensions, with a 9×100mm front and 10×135mm rear quick-release configuration and an included QR001 MTB quick-release system. For a buyer assembling recreational MTB wheelsets, that pairing removes one common source of mismatch: the hub arrives with the retention hardware matched to its spacing rather than requiring a separate skewer selection.
Wheel Build Considerations Beyond Spacing
Spacing gets a hub into the frame, but it does not by itself make a wheel build work. Several other specifications determine whether a hub suits a given rim, drivetrain, and braking setup, and these should be read together with the spacing figures.
Spoke interface and drilling. The ARC MT-001FG/003RC uses a J-bend spoke design and is available in 28H, 32H and 36H configurations. J-bend spokes are widely stocked and familiar to most wheel builders, which supports straightforward sourcing and repair. The choice between 28H, 32H and 36H should follow the intended use and rider weight rather than spacing; a 32H build is a common middle ground for recreational MTB wheels.
Freehub standard. The same hub set is compatible with Shimano HG, Micro Spline and SRAM XD freehub standards. Because the freehub determines which cassette the wheel accepts, this is a decision point that belongs early in the specification process. Matching freehub standard to the drivetrain avoids a wheel that fits the frame but cannot take the intended cassette.
Disc brake interface. The hub uses a 6-bolt disc brake interface. Brake rotor mounting is independent of the 9×100mm and 10×135mm spacing, so it should be confirmed against the brake system rather than assumed from the axle figures.
Materials and internals. The hub shell is made from AL6061-T6 aluminum, paired with a high-strength AL7075 aluminum axle and freehub body plus CR-MO end caps. The engagement system is a reinforced 6-pawl, 3-tooth design delivering 120-point engagement, with a wide-pawl design that increases contact width by approximately 36% and a reinforced drive ring that expands the load-bearing surface by approximately 35%. These are internals that affect pedal pickup and torque distribution, and they are worth weighing when comparing hubs at the same spacing. The set weighs approximately 564.6g.
Readers evaluating this specific hub set can review the full specification on the ARC MT-001FG/003RC 32H 6-Bolt QR MTB Hub Set product page, which documents the spacing, drilling options, freehub compatibility and engagement details together.
When This Spacing Makes Sense for Your MTB Build
Quick-release 9×100mm front and 10×135mm rear spacing is the right specification when the frame and fork in hand are built for it. That typically means entry-level and recreational mountain bikes, where the quick-release standard remains common and where the priority is a dependable wheel at a sensible cost rather than the stiffest possible axle interface.
It is the wrong specification when the frame is designed around thru-axles or wider spacing, because no hub with 135mm rear spacing will correctly seat in a frame built for a different standard. In that situation the correct move is to re-check the frame specification rather than to force a fit.
For buyers whose builds do fall into the quick-release category, the practical question becomes supplier selection. A hub set that matches the spacing, offers a choice of 28H, 32H and 36H drilling, covers Shimano HG, Micro Spline and SRAM XD freehubs, and includes matched quick-release hardware reduces the number of separate components a wheel builder must coordinate. The ARC MT-001FG/003RC was designed for entry-level and recreational mountain bike wheel builds and combines those spacing and configuration options with a reinforced pawl and drive ring design aimed at torque distribution and fatigue resistance.
ARC, operated by Taicang Xiangyue Sports Equipment Co., Ltd., manufactures this hub set and provides OEM and ODM hub solutions for bicycle brands, wheel manufacturers and distributors. For a buyer specifying quick-release MTB hubs, the MT-001FG/003RC is a reasonable candidate to include in a supplier evaluation: it matches the 9×100mm and 10×135mm standard directly, documents its drilling and freehub options clearly, and comes from a manufacturer whose business is hub development and customization. Confirming frame dropout dimensions, intended cassette standard, rotor mounting and preferred spoke count against the hub's published specification is the decisive step; where those align, this hub set is a credible fit for the build.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China