Micro Spline

Specifying MTB Hubs for Shimano HG, Micro Spline and SRAM XD Freehubs

15 min read
On this page 6 sections

Specifying an MTB hub begins with a decision many product managers defer until late in the program: which freehub standard the wheel is built around. That choice determines which cassettes fit, how the hub body is machined, and what the buyer must confirm with the frame and drivetrain supplier. Treating the freehub as an afterthought is one of the most common sources of rework in wheelset development, because a hub shell that is otherwise sound cannot be recovered by a cassette that will not seat. Shimano HG, Micro Spline and SRAM XD represent three distinct interfaces, and a hub platform offered in all three configurations, such as the ARC MT-010FCB/RCB, lets a brand serve several drivetrain programs without redesigning the wheel each time.

Why the Freehub Standard Is a Specification Decision

The freehub body is the mechanical interface between the cassette and the hub shell. It carries the cassette splines, houses the engagement mechanism and transfers drive torque into the shell. Because the cassette must seat fully and clamp correctly, the spline profile is not a cosmetic detail: it fixes which drivetrains the wheel can accept and constrains the hub body's outer diameter, length and machining.

For a product manager planning a trail, XC or all-mountain platform, the freehub choice ripples outward. It determines the cassette inventory the wheel can support, the drivetrain brands the build can be sold with, and the service parts a distributor must stock. It also interacts with the rest of the hub specification, since axle type, end caps and frame spacing must all be consistent with the chosen interface. Deciding the freehub standard early, alongside the frame and drivetrain brief, prevents a situation where a hub is designed, sampled and then found to accept only one cassette family.

How HG, Micro Spline and SRAM XD Differ at the Hub

The three standards differ most visibly in spline geometry and cassette retention.

Shimano HG is the long-established interface, using a splined body on which the cassette slides and is secured by a lockring. It is widely understood across the supply chain and remains common on many MTB builds, which makes it a familiar baseline for distributors and service networks.

Shimano Micro Spline is a later, finer-spline interface developed for Shimano's 12-speed mountain drivetrains. Its spline pattern is different from HG, so a Micro Spline cassette will not seat on an HG body and vice versa. For specifiers, this means the hub body must be machined to the Micro Spline profile if the program is built around that drivetrain.

SRAM XD uses its own interface, in which the cassette threads onto the freehub body rather than sliding onto splines. The body therefore needs the correct thread and seating geometry. As with Micro Spline, an XD cassette cannot be fitted to an HG or Micro Spline body.

The practical conclusion is straightforward: each standard implies a distinct freehub body, and the cassette-to-freehub match is the first compatibility check in any hub specification. Body length, spline count and retention method should all be confirmed against the intended cassette family before the hub drawing is released.

Matching the Rest of the Hub to the Chosen Standard

Freehub selection does not stand alone. Once the interface is fixed, the surrounding hub specification must be checked for consistency.

Axle type and end caps are the first consideration. A hub offered with quick-release and thru-axle options needs the correct end caps for the frame standard in use, and the freehub body must be matched to the axle configuration. Spoke count is a separate but simultaneous decision: 28H, 32H and 36H builds suit different rider weights, wheel sizes and intended use, and the hub drilling must align with the rim and spoke plan.

It is also worth separating the freehub standard from the engagement architecture. The spline interface determines cassette fit; the pawl or ratchet system determines pickup and torque transfer. These are independent choices, and a specifier should evaluate each on its own terms rather than assuming that a particular freehub standard implies a particular engagement design. Conflating the two can lead to a hub that fits the drivetrain but does not match the ride character the program intends to deliver.

Specifying One Platform Across Multiple Drivetrain Standards

Brands that sell into several drivetrain ecosystems, or distributors serving mixed fleets, face a familiar problem: maintaining separate hub designs for each cassette standard multiplies tooling, documentation and inventory. A hub platform offered with a choice of freehub bodies addresses this directly.

The ARC MT-010FCB/RCB is an example of this approach. The hub set is offered in configurations compatible with Shimano HG, Micro Spline and SRAM XD freehub standards, so a single platform can be specified across different drivetrain programs. Beyond the freehub choice, the set combines an AL6061-T6 aluminum and carbon-tube composite hub shell with high-strength AL7075 aluminum axle, freehub body and end caps, and is available in 28H, 32H and 36H configurations with both quick-release and thru-axle options and a 6-bolt disc interface. For a wheel program that needs to cover more than one cassette family, this gives specifiers a documented material and configuration basis to evaluate rather than starting from a new design for each standard.

ARC manufactures MTB hub sets and provides OEM and ODM solutions for bicycle brands, wheel manufacturers and distributors, which is relevant when freehub standard selection needs to be handled at the manufacturing stage rather than patched in later. Buyers comparing suppliers for a multi-standard program can reasonably place a platform of this kind on their evaluation list, provided they confirm the specific configuration against their own cassette, axle and spoke requirements.

Checks Before Releasing a Hub Specification

A short verification routine before ordering reduces the risk of a mis-specified batch:

  • Confirm the cassette family and its freehub standard, and match it to the specified freehub body.
  • Confirm axle type (quick-release or thru-axle) and end-cap configuration against the frame standard.
  • Confirm spoke count and drilling against the rim and spoke plan.
  • Check that engagement architecture has been evaluated separately from the freehub interface.
  • Verify the chosen configuration against the supplier's documented product data and request confirmation for any detail not stated in the published specification.

Working through these points early keeps the freehub decision where it belongs, at the front of the specification rather than the end. For programs spanning Shimano HG, Micro Spline and SRAM XD, a platform such as the ARC MT-010FCB/RCB is worth assessing as a single basis for all three, with the final configuration confirmed against the cassette, axle and spoke requirements of each build.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China