For wheel builders planning a road disc carbon wheelset around bladed carbon spokes, the hub set is where the design either locks in or runs into compatibility trouble. The ARC MT-105F/R answers that starting point with a defined specification: an asymmetric 18-hole front and 21-hole rear 2:1 drilling pattern, a dedicated 4.2mm carbon-spoke interface standardized around Hongji Weiye B-type spokes, a claimed set weight of about 328.5g (92.4g front, 236.1g rear), and a configurable menu covering 36T or 54T ratchets, Center Lock mounting, 12×100mm and 12×142mm thru-axles, five freehub standards, and three bearing grades. Whether that package suits a given carbon wheel program depends less on the headline weight than on how these details line up with the intended rim, spoke supply and drivetrain mix.
Why carbon-spoke builders should start with the interface, not the weight
Carbon spokes are not a drop-in substitute for steel. Their round-head, bladed geometry, larger effective flange contact area and different stiffness mean the hub's spoke holes, flange thickness and seat geometry have to be designed around them from the beginning. A hub that accepts steel J-bend or straight-pull spokes will not necessarily accept a carbon blade without play, poor seating or stress concentrations at the head.
The MT-105F/R is built specifically around a 4.2mm carbon-spoke interface, intended for compatible round-head carbon bladed spokes, with Hongji Weiye B-type spokes as the standard configuration. For a wheel brand, that standard matters in two ways: it defines the spoke supply chain the hub was validated against, and it gives the builder a fixed reference when sourcing or substituting spokes. If the plan is to use a different carbon spoke brand, the interface dimensions and head seat should be checked against the ARC specification before tooling or spoke orders are committed, because a hub that suits one B-type spoke may not seat another manufacturer's head profile correctly.
This is also why weight should be treated as an outcome rather than the first filter. A 328.5g set is competitive for this category, but the number only becomes useful once the interface, drilling and axle standard are confirmed to fit the wheel being designed.
18H/21H 2:1 layout and what it means for tension balance
The front hub carries 18 spoke holes; the rear carries 21 in a 2:1 configuration. The logic is straightforward for disc-brake road wheels: the rear wheel has to manage drive torque on one side and braking torque through the disc on the other, and those loads are not symmetric. A 2:1 lacing pattern lets the builder use more spokes on the higher-load side and fewer on the opposite side, which helps balance spoke tension and distribute load more evenly across the rim.
For a carbon rim, this speaks directly to build quality. Carbon rims are sensitive to uneven tension, and a hub designed with this ratio gives the wheel builder a starting geometry that supports consistent tension on both sides rather than forcing a compromise lacing. The asymmetric front and rear counts also mean rim drilling has to be planned around the hub rather than retrofitted, so the MT-105F/R layout should be confirmed against the rim specification early in the design cycle.
The practical takeaway: the 18/21H pattern is a design input for the rim and spoke plan, not just a hub specification. Builders working with a specific carbon rim should verify that the rim's spoke-hole count and orientation match the 2:1 rear pattern before ordering.
Materials, weight and the 328.5g figure
ARC divides the material task across the hub set. The hub shell is forged AL6061-T6 aluminum, while the axles, freehub body and end caps use high-strength AL7075. The split is sensible: the shell needs to be light and formable into the flange and spoke interface geometry, while the load-bearing rotating parts benefit from a higher-strength alloy.
The claimed complete set weight is approximately 328.5g, split as 92.4g front and 236.1g rear. That rear figure reflects the greater complexity of the driven hub: freehub mechanism, ratchet, larger axle assembly and the 2:1 flange geometry. Wheel builders should treat 328.5g as the hub-set contribution to the wheelset and add rim, spoke, nipple and rotor-lock hardware to reach the final build weight. Because hub weight alone does not determine wheel stiffness or durability, the figure is best used comparatively at the specification stage, not as a performance claim.
Drivetrain, axle and bearing options to specify
The MT-105F/R supports a broad spread of build configurations, and this is where much of its value to a wheel brand sits.
- Ratchets: ARC's patented one-piece ratchet architecture is offered in 36T and 54T versions, giving builders a choice of engagement character for the intended riding discipline.
- Freehubs: Shimano HG, Road Micro Spline, SRAM XDR, Campagnolo N3W, and Campagnolo 11/12-speed are listed standards, which covers most current road and gravel drivetrain families.
- Mounting and axles: Center Lock disc interface, with 12×100mm front and 12×142mm rear thru-axle spacing.
- Bearings: S&S steel, ENDURO, and CeramicSpeed options are available.
For a wheel brand, the freehub list is often the deciding factor in whether one hub platform can serve several SKUs. Covering Shimano, SRAM and Campagnolo standards from a single hub set reduces the number of distinct hub part numbers a builder has to stock, which matters when a carbon wheelset range is sold across European markets with mixed drivetrain preferences. The bearing tiers also let a brand position the same hub at different price points, though ARC's published material does not state bearing life or drag figures, so those should be confirmed rather than assumed.
One caution on the ratchet choice: 36T and 54T differ in engagement count, and the right pick depends on the rider profile the wheel is aimed at. The specification should be fixed per SKU rather than treated as interchangeable late in assembly.
What to confirm with ARC before ordering
The published specification is a solid starting point, but a few items are worth confirming directly before samples or production orders are placed.
First, spoke compatibility: confirm whether the 4.2mm interface accepts only Hongji Weiye B-type round-head carbon blades or a wider range of compatible spokes, and request the relevant head and seat dimensions if an alternative spoke is planned.
Second, ratchet and freehub combination: verify that the desired 36T or 54T ratchet is available with each freehub standard the range requires, since option availability can vary by combination.
Third, bearing tier and its effect on the bill of materials and positioning, along with any service or replacement-part expectations.
Fourth, axle and end-cap configuration for the specific frame standards in the target market, and confirmation of the Center Lock interface on both front and rear.
ARC, based in Taicang and founded in 2013, manufactures hubs and supplies OEM/ODM solutions to wheel manufacturers and brands, which makes it a reasonable candidate for a carbon-spoke road disc program where the hub interface has to be matched to a specific rim and spoke plan. The MT-105F/R is worth putting on the evaluation list for builders whose design calls for an 18/21H 2:1 layout and a defined carbon-spoke standard; the next step is to send the rim and spoke specification to ARC and ask for confirmation of the interface, ratchet and freehub combination, and bearing options against that build. Product details are available on the ARC MT-105F/R 18/21H Carbon-Spoke Center Lock Road Hub Set page.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China