Design and Spoke Interface for Carbon Wheels
Carbon-spoke road disc wheels place demands on a hub set that differ from conventional steel-spoke builds. The spoke interface is the first point of evaluation: carbon bladed spokes have their own head geometry, and a hub drilled for standard round steel spokes will not seat them correctly. The ARC MT-080F/R addresses this directly with 4.2mm spoke holes designed for compatible round-head carbon bladed spokes, including VONOA and Hongji Weiye configurations.
That detail matters more than it may appear at the quotation stage. An incorrect hole diameter or seat profile can lead to uneven seating, concentrated stress at the spoke head, and inconsistent tension during the build. For wheel builders producing carbon-spoke wheels as a repeatable product line, the interface needs to be specified for the spoke type from the outset, not adapted afterward. The MT-080F/R is built around that premise: a dedicated carbon-spoke interface rather than a dual-purpose drilling.
The hub shell follows a compact small-flange architecture. On a disc-brake road wheel, flange geometry influences bracing angle and, in turn, lateral stiffness and spoke tension balance. A small-flange layout keeps the hub body compact while remaining compatible with the spoke counts and lacing patterns typical of lightweight carbon wheel designs. Combined with the Center Lock disc interface and 12×100mm front / 12×142mm rear thru-axle spacing, the platform aligns with current road disc frame and fork standards, which simplifies integration for builders already working within that ecosystem.
Spoke Count, Lacing, and Load Distribution
The MT-080F/R uses a 20-hole front and 24-hole rear configuration with a 2:1 spoke arrangement at the rear. This is a deliberate choice for disc-brake road wheels, where the rear hub carries drivetrain torque on one side and braking loads on the other. A 2:1 pattern allows the drive side and non-drive side to use different spoke counts, which helps balance tension across the wheel rather than forcing equal counts into an asymmetric load case.
For builders, the practical implications are straightforward. A 20/24 count suits lightweight carbon rim profiles that are drilled for these counts and avoids over-building a wheel whose rim is already stiff. The 2:1 lacing gives the wheel builder a defined starting point for tension targets, since the ratio itself is intended to equalize spoke tension between the two sides. Builders should still validate final tension values against the specific rim and spoke combination, as rim depth, spoke type, and rider weight all interact with the hub's lacing geometry. The hub sets the framework; the rim and spoke selection complete the load path.
This configuration also has a production benefit for wheel brands. A fixed, documented spoke count and lacing pattern makes it easier to standardize build sheets, spoke lengths, and quality checks across a product line, rather than re-engineering the hub interface for each rim model.
Materials, Weight, and Bearing Options
The hub shell is forged from AL6061-T6 aluminum, while the axles, freehub body, and end caps use high-strength AL7075. This combination reflects a common approach in performance hub design: a forged shell for structural consistency and machined 7075 components where strength-to-weight matters most in the axle and freehub assembly. The listed complete hub set weight is approximately 333.8g, a figure that positions the MT-080F/R within the lightweight segment relevant to carbon-spoke road builds.
Weight alone does not determine wheel performance, and builders should treat the hub weight as one input among several, alongside rim mass, spoke count, and tire choice. What the figure does indicate is that the hub set is intended for builds where low rotating mass is a design goal rather than an afterthought.
Bearing selection is where the MT-080F/R offers meaningful customization. S&S steel bearings are available as the standard option, with ENDURO and CeramicSpeed bearings offered as alternatives. These choices affect drag, service intervals, and cost, and the right selection depends on the target price tier and the riding conditions the wheel is designed for. A wheel brand building a value-oriented road disc wheelset may find steel bearings appropriate, while a premium carbon-spoke build may justify a ceramic upgrade. Because the bearing options are defined within the same hub platform, builders can differentiate product tiers without changing the hub's external geometry or spoke interface.
The rear hub's patented one-piece ratchet system, available in 36T and 54T versions, is part of the same engagement decision. Higher tooth counts reduce the engagement angle, which some riders prefer for quicker power pickup; lower counts can suit different priorities. Offering both options lets a wheel brand tune the freehub feel to its target rider without switching hub models.
Compatibility and Customization for OEM/ODM
Drivetrain compatibility is often the deciding factor when a hub set is evaluated for a product line. The MT-080F/R supports Shimano HG, Road Micro Spline, SRAM XDR, Campagnolo N3W, and Campagnolo 11/12-speed freehub standards. For a wheel brand selling across multiple markets, that range means a single hub platform can be configured to cover the major road drivetrain systems rather than requiring separate hub sources for each.
The axle standard is fixed at 12×100mm front and 12×142mm rear thru-axle, matching the current road disc norm, and the Center Lock interface keeps rotor mounting consistent with widely used disc-brake components. Builders should confirm their frame and fork specifications and their intended rotor and cassette combinations before finalizing a build sheet, as these remain the buyer's responsibility even when the hub supports the relevant standard.
As a professional bicycle hub manufacturer, ARC provides OEM and ODM solutions for bicycle brands, wheel manufacturers, and distributors, covering road, mountain, gravel, and e-bike applications. For carbon wheel builders, that matters at the point where a catalog hub does not quite fit a planned product: customization discussions can address freehub specification, bearing selection, and ratchet configuration within the MT-080F/R platform, backed by CNC machining and quality control processes at the Taicang facility. The practical next step for a wheel brand evaluating this hub set is to define the target rim, spoke type, drivetrain coverage, and price tier, then confirm which bearing and ratchet combinations align with each product variant. Builders working on lightweight carbon-spoke road disc wheels will find the MT-080F/R worth including in their supplier evaluation, particularly where a defined carbon-spoke interface and multi-standard freehub coverage are prerequisites rather than optional extras.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China