ARC GT-002FR CNC

ARC GT-002FR CNC Track Hubs: What Fixed-Gear and Track Builders Should Know

15 min read
On this page 5 sections

For fixed-gear and track builders, the rear hub is not a background component. It carries the drivetrain load, sets the chainline, and determines how securely the sprocket stays in place under repeated acceleration and back-pedaling. The ARC GT-002FR CNC Track Hub is designed specifically around those demands, combining a CNC-machined aluminum shell with an integrated locking structure, double-sided fixed-gear threading, and a supplied 16T cog and lockring. This article looks at what the hub actually offers, where its design choices matter in a build, and what a buyer should confirm before specifying it for a frameset or a small OEM/ODM order.

What the GT-002FR Is Built For

The GT-002FR is purpose-built for fixed-gear and track cycling rather than adapted from a multi-speed hub platform. That distinction shapes several of its features: a single-speed drivetrain interface, thread-based sprocket mounting, and a locking arrangement intended to keep the cog fixed when the rider applies torque in either direction.

For a track or fixed-gear wheelset, this focus matters at the specification stage. Builders need consistent hub flange geometry for lacing, predictable chainline when the hub is paired with a given crank and bottom bracket, and a sprocket interface that can be assembled and serviced without specialty tooling beyond a lockring tool. The GT-002FR is supplied with a 16T fixed-gear cog and lockring, so the drivetrain interface arrives as a matched set rather than as a hub that still needs a cog sourced separately. For small builders and distributors assembling complete fixed-gear wheelsets, that simplifies the bill of materials and reduces the risk of pairing a hub with an incompatible cog.

Materials and CNC Construction

The hub shell is machined from AL6061-T6, a widely used aluminum alloy chosen for a balance of strength, machinability, and weight. The axle, freehub components, and end caps are made from high-strength AL7075 aluminum. Using a higher-strength alloy for the axle and load-bearing parts while keeping the shell in 6061 is a sensible split: the shell benefits from consistent machining and good fatigue behavior, while the axle and end caps take the more concentrated loads.

Fully CNC-machined construction is relevant to builders for reasons beyond appearance. Machining from billet allows tighter control over bearing bores, flange spacing, and thread concentricity than many cast or forged-and-machined alternatives, and it supports the dimensional consistency that wheel lacing and chainline setup depend on. The same machining approach is what allows a manufacturer to adjust dimensions for custom runs, which becomes relevant later when discussing OEM/ODM work with ARC.

Buyers should note that material grades and machining method describe how the hub is made, not a guaranteed performance figure. Weight, bearing specification, and service life depend on the complete build, the bearing selection, and riding conditions, so those details are best confirmed against the current specification sheet rather than inferred from the alloy alone.

Locking Structure and Sprocket Setup

The most build-relevant feature of the GT-002FR is its integrated locking structure combined with double-sided fixed-gear threading. Thread-mounted cogs on fixed-gear hubs face a specific problem: forward pedaling torque tightens the cog, but back-pressure—skidding, resisting, or rolling backward—can work it loose unless it is held by a lockring. The integrated locking structure addresses sprocket retention directly, and the lockring supplied with the hub is matched to that interface.

Double-sided threading gives builders a practical choice. The hub can be set up with the cog and lockring on either side, which helps when adjusting chainline relative to a given frame and crank combination, or when a frame's dropouts and chainstay clearance favor one orientation. It also means the same hub model can serve builds with different drivetrain placement without a separate SKU.

Before ordering, builders should verify a few points against their own build:

  • Frame spacing and dropout type — confirm the hub's over-locknut dimension matches the frame, and that the axle and end-cap configuration suits the dropout style.
  • Chainline — check which side and sprocket position produce the intended chainline with the chosen crank, and confirm the thread direction and lockring engagement on the selected side.
  • Cog and lockring compatibility — the supplied 16T cog suits many track and street ratios, but riders planning a different gear should confirm that replacement cogs and lockrings match the hub's threading and locking interface.
  • Tire and frame clearance — a 16T cog combined with a given chainring sets the gear ratio and chain length; verify clearance at the chainstay and dropout before finalizing.

These are normal pre-purchase checks rather than limitations of the hub. Handling them at the specification stage avoids the more costly alternative of discovering a chainline or spacing mismatch after the wheel is built.

Working With ARC on Track and Fixed-Gear Hubs

The GT-002FR comes from ARC, the brand of Taicang Xiangyue Sports Equipment Co., Ltd., a bicycle hub manufacturer founded in 2013 and based in Taicang, Jiangsu, China. ARC designs, manufactures, and customizes performance hubs and provides OEM and ODM solutions for bicycle brands, wheel manufacturers, and distributors, with a stated production approach built on CNC machining, precision manufacturing, engineering expertise, and quality control systems.

That background is relevant to how a builder or component buyer might use the GT-002FR. For a custom wheel builder, the hub offers a defined starting point: a track-specific shell, a matched cog and lockring, and a locking structure that removes some of the uncertainty around sprocket retention. For a brand or distributor planning a fixed-gear or track wheelset line, the more important question is whether the hub can be adapted to the intended specification—flange dimensions, axle configuration, finish, or branding—and that is where ARC's OEM/ODM capability becomes the deciding factor rather than the stock model alone.

A sensible next step is to evaluate the GT-002FR against a specific build: confirm spacing, chainline, and cog choice, then request a sample to check machining quality, thread engagement, and lockring fit in hand. Buyers with a defined wheelset program can take the same sample evaluation into a customization discussion with ARC, covering the dimensions and finish that need to change and the volumes involved. The ARC GT-002FR CNC Track Hub is a reasonable first candidate for track and fixed-gear projects where secure sprocket mounting, flexible setup, and a CNC-machined aluminum structure are the priorities—provided the frame spacing and chainline are confirmed before the order is placed.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China